Hitachi DS14DVF Support Question
Hitachi DS14DVF Support Question
Find answers below for this question about Hitachi DS14DVF - 14.4 Volt 3/8" Driver/Drill.Need a Hitachi DS14DVF manual? We have 2 online manuals for this item!
Question posted by mdallison on November 20th, 2010
Ds14dvf Keyless Chuck Removal
I need to replace the keyless chuck on my DS14DVF drill. I removed the screw from te bottom of the chuck but it still will not come off. Is there a secret to getting the chuck off?
Current Answers
Related Hitachi DS14DVF Manual Pages
Instruction Manual - Page 3
... SIGNAL WORDS
WARNING indicates a potentially hazardous situation which, if ignored, could result in the Instruction Manual before it occurs, and by WARNINGS on the power tool and in this Instruction Manual and in the sections which , if not avoided, may cause machine damage. Most accidents that has not been specifically recommended...
Instruction Manual - Page 4
... Avoid accidental starting. Distractions can be used with another battery. (2) Use battery operated tool only with integral batteries or a separate battery pack must be caught in personal injury. ...the tool on the switch or inserting the battery pack into a tool that may be recharged only with your finger on . A charger that have the switch on invites accidents. (4) Remove adjusting...
Instruction Manual - Page 5
... away from one tool may affect the tools operation. If damaged, have the tool serviced by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other small metal objects that can make a connection from other metal objects like: paper clips, coins, keys, nails, screws, or other...
Instruction Manual - Page 6
...driver drill operates by its operation or unauthorized personnel.
11. Don't use a power tool for extended periods. don't use power tools if the plastic housing or handle is cracked. Keep all screws... the drill bit or chuck during operation. NEVER place your hands, fingers or other body parts near the tool's moving parts. Use right tool. NEVER allow the tool to replace the ...
Instruction Manual - Page 7
...for repairs by a Hitachi authorized service center. 15. V volts direct current
no load speed
---/min ... Carefully handle power tools. ALWAYS wear eye protection that meets the requirement of the latest... solvent. English 14. no .......... revolutions per minute
7 NEVER use a tool which is defective or operating abnormally.
Should a power tool be deformed, cracked, or damaged. 16....
Instruction Manual - Page 8
...7. Do not operate battery charger with damaged cord or plug-replace them immediately.
8 An extension cord should not be stepped ...UC12SD and EB1412S and EB1414 for example:
1250watts 125 volts = 10 amperes
9. If extension cord must be ...45)
0
2
2
3
3
4
18
18
18
18
18
18
18
16
16
14
16
14
* If the input rating of plug
on (1) battery charger, (2) battery, and (3)...
Instruction Manual - Page 9
...reduce risk of electric shock or fire.
12. Removing the battery will not reduce this manual. OTHER...volts). charge when the temperature is completely worn out. use an engine generator or DC power to a qualified serviceman.
11. store the battery or battery charger in a fire. Keep the battery away from receptacle before you can use of injury:
WARNING: Improper use the cordless driver drill...
Instruction Manual - Page 11
... in this Instruction Manual may show details or attachments that differ from those on your own power tool.
Cordless Driver Drill Keyless Chuck
Cap L Indication Switch Trigger
Handle
Shift Knob Housing Bit
Push Button
Nameplate
R Indication
Keyless Chuck
Cap L Indication Switch Trigger
Handle
Battery
Shift Knob Housing
Bit
Push Button
Nameplate
R Indication
Battery
11
MODEL...
Instruction Manual - Page 13
...°C)
DC 9.6V
DC 12V
DC 14.4V
DC 1.55A
DC 1.55A
DC 1.55A
2.6 lbs. (1.2kg) 3.3 lbs. (1.5kg) 3.5 lbs. (1.6kg)
13 Cordless Driver Drill
Model Motor No-load speed
Low High
DS9DVF
0-280/min 0-840/min
DS12DVF DC motor 0-350/min 0-1050/min
DS14DVF
0-400/min 0-1200/min
Capacity Drilling
Wood (Thickness 11/16" (18mm...
Instruction Manual - Page 14
... receptacle, make sure the following points. ⅜ The power source voltage is not damaged. Withdraw battery from the tool handle while pressing the latch (1 pc. REMOVAL AND INSTALLATION METHOD OF BATTERY
⅜ How to remove the battery.
If charged at voltage higher than indicated on the nameplate. ⅜ The cord is stated on...
Instruction Manual - Page 15
Make sure it
repaired immediately.
3. Insert the plug of battery charger into the receptacle, charging will
commence and the pilot lamp will go off even if more than four hour has passed after start of the battery charger. NOTE: If the pilot lamp dose not light, pull out the plug from the receptacle.
15 one hour, when the battery is properly mounted. ⅜ In approx.
Have it ...
Instruction Manual - Page 16
...discharge in case of the failures. When you continue to use or exposure to battery use the tool and exhaust the electric current, the battery may not light. If such a battery is not ... the plug when removing from the battery charger. As the internal chemical substance of new batteries and batteries that the power of the tool becomes weaker, stop using the tool and recharge its...
Instruction Manual - Page 17
...sleeve is tightened.
(2) Dismounting the bit. Confirm that the trigger switch is depressed, the tool rotates.
Firmly grasp the ring and tighten the sleeve by
Triger switch
pushing the R-side of...as viewed from the front). (See Fig.5)
CAUTION: When mounting a bit into the keyless drill chuck. English
OPERATION
1. Insert a screwdriver bit etc. Firmly grasp the ring and loosen the ...
Instruction Manual - Page 18
...drill rotates at a high speed. DS12DVF / DS14DVF
When the diameter of the hole exceeds 3/16"(5mm). When using this unit as a screwdriver, line up the cap drill mark
" " with the triangle mark on the outer body. When set to "HIGH", the drill...with the triangle mark on the outer body. Model Metal Drilling
Wood Drilling
Wood Screw Tightening
Table 2
DS9DVF
When the diameter of the hole...
Instruction Manual - Page 20
... selected content shown in -lbs. (245 kg-cm)(DS14DVF)
Thick screw tightening When used . Use the bit and socket matching the screw diameter.
CAUTION: q While operating the Cordless driver drill, take care not to screw type, screw size and material used as the screw heads will be damaged.
20 Use after drilling a pilot hole.
If the motor is locked...
Instruction Manual - Page 21
... replacement of parts because of wear from normal use a driver bit of children.
5. So replace it...removed with a soft cloth or a cloth dampened with loosened, screws is worn or broken, it out. The bits should be performed by a Hitachi Authorized Service Center. To assure that only authorized replacement parts will be changed without prior notice.
21 MODIFICATIONS: Hitachi Power Tools...
Instruction Manual - Page 22
...dangerous and could cause injury or mechanical damage. The use a particular replacement part or accessory with this tool. STANDARD ACCESSORIES
1
2
3
4
DS9DVF
1 Phillips bit (No... Battery (EB1212S or EB1214L 2
3 Battery Charger (UC12SD 1
4 Plastic Case (Code No. 319967 1
1
2
3
4
DS14DVF
22
1 Phillips bit (No. 2 × 55L)(Code No. 318236) ....... 1 2 Battery (EB1412S or EB1414 2 3 ...
Instruction Manual - Page 23
Battery (EB1412S, EB1414)(For DS14DVF)
NOTE Specifications are subject to change without any obligaiton on the part of the HITACHI.
23 Battery (EB912S, EB914)(For DS9DVF) 2. Battery (EB1212S, EB1214L) (For DS12DVF)
3. English
OPTIONAL ACCESSORIES.....sold separately
1.
Parts List - Page 1
F869
ELECTRIC TOOL PARTS LIST
CORDLESS DRIVER DRILL Model DS 14DVF
2003 • 2 • 24 (E2)
1 3
2
8
2
4
9
10 11
12
18
13
19
14
20
21
22
23 24
25
5 6 7
15 16 17
26
501
30
501
31
32
38
502
37 36 35
34
503
33
27 28 29
504
39
505
42 41
40 LIST NO.
Parts List - Page 2
CODE NO.
1 318-228
DESCRIPTION SPECIAL SCREW (LEFT HAND) M5X27
NO. USED
1
REMARKS
2 312-516 DRILL CHUCK 10TLRD-N (W/O CHUCK WRENCH) 1
3 320-660 GEAR BOX ASS'Y
1 INCLUD. 4-25
4 320-661 CAP
1
5 318-...-715 RING GEAR
1
13 312-705 PLANET GEAR (C) SET (3 PCS.)
3
14 312-704 WASHER (A)
1
15 312-697 REAR CASE
1
16 315-817 SCREW SET D3X12 (6 PCS.)
4
17 311-962 SHIFT ARM
1
18 315-137 ...
Similar Questions
Hitachi Keyless Chuck Removal: Hitachi D10-vh
I have an Hitachi D10-VH 3/8" corded drill with keyless chuck and I wish to remove the keyless chuck...
I have an Hitachi D10-VH 3/8" corded drill with keyless chuck and I wish to remove the keyless chuck...
(Posted by detcord 3 years ago)
How To Remove Keyless Chuck On Hitachi D10vf Drill
(Posted by detcord 3 years ago)
How Do I Pull The Motor Stator To Replace The Bearings?
My C8FB2 bearing are shot from brick dust. I have the new bearings and the motor housing off but can...
My C8FB2 bearing are shot from brick dust. I have the new bearings and the motor housing off but can...
(Posted by jhraley 11 years ago)
How To Read Battery Symbols On Charger
I have a Hitachi 14.4 volt cordless drill, DS 14DV, but had to get after market batteries which fit ...
I have a Hitachi 14.4 volt cordless drill, DS 14DV, but had to get after market batteries which fit ...
(Posted by sandy63901 12 years ago)