Hitachi CPX430 Support Question
Hitachi CPX430 Support Question
Find answers below for this question about Hitachi CPX430.Need a Hitachi CPX430 manual? We have 1 online manual for this item!
Question posted by mcduff52 on September 11th, 2012
Usb Adapter
Do they make an adapter from the projector to laptop with a USB port?
Current Answers
Related Hitachi CPX430 Manual Pages
User Manual - Page 3
...8226; The information in this manual. OSD Message 20 Table 10. ENGLISH
Liquid Crystal Projector
USER'S MANUAL
Thank you for purchasing this "USER'S MANUAL" thoroughly to change without...WARNING • Please read the accompanying manual "SAFETY INSTRUCTIONS" and this liquid crystal projector. After reading, store this document or contents is a registered trademark of this ...
User Manual - Page 4
... from the unit can be magnified for closer viewing.
BEFORE USE
Contents of Package
Make sure all of the following items are quickly available. NOTE • Keep the ...modo tale da poter comprendere quanto riportato ai fini di un corretto utilizzo del proiettore. Projector
Liquid Crystal Projector CP-X430W USER'S MANUAL Please read this manual) Safety Instructions
Carrying Bag
ENGLISH-2
...
User Manual - Page 5
...Ventilation Openings
(Intake)
Zoom Knob Focus Ring Remote Control Sensor Lens Foot Adjuster
Lens Cap
FRONT/LEFT VIEW OF THE PROJECTOR
Control Panel (Refer to P.9 "OPERATIONS")
STANDBY/ON Button KEYSTONE Button
Foot Adjuster Button
Filter Cover
( ) Air Filter... below)
Remote Control Sensor DVI Terminal RGB IN 1 Terminal RGB IN 2 Terminal
CONTROL Terminal RGB OUT Terminal USB Terminal
ENGLISH-3
User Manual - Page 6
.... Never look directly into the laser beam outlet or point the laser beam at other than those specified herein may result in place of the projector. • Do not disassemble the remote control transmitter.
The laser beam can cause vision problems. CAUTION • Use of controls or adjustments or performance of...
User Manual - Page 7
...
Install the AA batteries into the remote control
transmitter.
1. Remove the battery cover. ENGLISH-5 Make sure the plus and minus terminals are correctly
oriented.
1
2
3. This could cause in ...leakage, which could result in fire or personal injury. • When loading the batteries, make sure the plus and minus poles are correctly oriented as indicated in the relative area or ...
User Manual - Page 8
... the desired angle. 3. Lift up position, this unit with ventilation holes blocked. • Do not install LCD projector in the table below for fine adjustment.
a: Distance from the projector to make screw. Angle Adjustment
Use the foot adjusters on critical parts (i.e.LCD panel, Lens Assy etc.). Installation Reference
Screen size [inches (m)]
40 (1.0)
a [inches...
User Manual - Page 9
... make sure that the projector is compatible with the device. • Secure the screws on the connectors and tighten. • For some RGB input modes, the optional Mac adapter is used with this manual and the separate "SAFETY INSTRUCTIONS". • Before connecting, turn off to all devices to be connected, except for the USB...
User Manual - Page 10
...
COMPONENT VIDEO CR/PR CB/PB Y
AUDIO
R
IN
S-VIDEO IN L VIDEO IN
AUDIO 1 2 AUDIO OUT USB IN
Display Monitor
%7*
1
RGB IN
2
RGB OUT
CONTROL
Computer (notebook type)
Speaker with amplifier
Computer (desktop type... including a computer and display, and an operating system. • This projector is recognized as a plug & play may not operate by connecting to be used. ENGLISH-8 Connect ...
User Manual - Page 11
...
Power OFF
1. During this manual, and the separate "SAFETY INSTRUCTIONS" thoroughly before the projector. • When a projector continues projecting the same image, the image may remain as an afterimage. The POWER indicator...connected, turn on the screen, and the message will reduce the life of the projector lamp and LCD panel. • To prevent any operation or no effect while the...
User Manual - Page 12
... MAGNIFY mode is displayed for the VOLUME, LANGUAGE and H PHASE. • The RESET button may be used from the supplied remote control transmitter or the projector control panel.
Table 3 .
The [ ] icon is cleared by running or setting the AUTO, ASPECT, INPUT SELECT or VIDEO, or by changing the input signal. •...
User Manual - Page 19
... it and do not scratch it. • Also, do not use the projector with the lamp cover removed. If unsure contact your dealer before replacing the lamp. Lamp
Reflector
Front glass
...Lamp Life Projector lamps have a finite life. The image will become darker, and hues will become weaker, ...
User Manual - Page 20
... the Lamp
1. Prepare a new lamp. 3. CAUTION • Ensure that the projector has cooled sufficiently, and gently
turn the projector right-side up. Loosen the two screws as shown in injury or accidents. •...; Do not use the projector with the lamp cover removed. Switch the projector OFF, remove the power cord from the power outlet, and wait at...
User Manual - Page 21
... work .
benzene or thinners). • Do not use detergents or chemicals other than those noted above (e.g. Switch the projector power supply OFF, and remove the power cord from the power outlet. 2. Other Maintenance
Maintenance Inside the Equipment For safety....
Please read the separate "SAFETY INSTRUCTIONS" thoroughly to prevent the temperature rising inside the projector.
User Manual - Page 24
...Replace with the MENU
no audio.
Table 11. The power cord is blurred. Use the projector or remote control transmitter to minimum.
The lamp is set.
Plug the power cord into an.... If the situation cannot be corrected, then contact your dealer.
Connect correctly.
7,8
The projector is present but The brightness adjustment knob Select BRIGHT with a new lamp.
17
WHISPER mode...
User Manual - Page 25
... 15-pin shrink plug USB jack (B type)
Optional Parts
Lamp: DT00471 Air Filter: NJ06131 * For others, consult your dealer. SPECIFICATIONS
ENGLISH
Table 12.
Specifications
Item
Specification
Product name
Liquid crystal projector
Liquid crystal panel
Panel size Drive system Pixels
2.3 cm (0.9 type) TFT active matrix 786,432 pixels (1024 horizontal x 768 vertical)
Lens...
User Manual - Page 28
... the case, it is "Composite Sync." TECHNICAL - 2 on G". • The image might be something wrong with this projector. • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer. • Depending on the DVI mode. Use of some cases. Refer to reduce the resolution and...
User Manual - Page 30
..., reboot the computer (soft reboot or reboot buttons).
Refer to operate a mouse. TECHNICAL (continued)
Connection to (4) above. For
PS/2 mouse control (for detail. USB Mouse (1) Connect the projector and computer with the appropriate cable. Refer to the descriptions of "DISC PAD" and "MOUSE/RIGHT button" of page 4. Refer to the descriptions of...
User Manual - Page 32
... power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and, after the computer has started up, turn on the projector
power supply. CRC_high : Upper byte of CRC flag for command data.
3 Command data
Command data chart
byte_0 byte_1 byte_2 byte_3 byte_4 byte_5
Action
Type
Setting...
User Manual - Page 33
... test data when the power supply is switched ON, and when the lamp is greater than indicated by the data length code, the projector will be guaranteed when the projector receives an undefined command or data. • Provide an interval of at least 40ms between the response code and any other works...
User Manual - Page 39
... device, pursuant to radio communications. REGULATORY NOTICES - 1 This equipment generates, uses, and can be used in CANADA
NOTICE: This Class B digital apparatus complies with the projector or specified.
These limits are designed to operate the equipment. Core
CAUTION: Changes or modifications not expressly approved by one or more of the FCC...
Similar Questions
What Is The Max Cable Length For Cable Between Projector & Laptop?
1. Can Hitachi CP - X1250 projector be ceiling mounted or on a platform hanging from ceiling?2. What...
1. Can Hitachi CP - X1250 projector be ceiling mounted or on a platform hanging from ceiling?2. What...
(Posted by xaverknoop 8 years ago)
Hitachi A100 Projector
My projector keeps shutting down and often will not come on after it has been cooled down. The red l...
My projector keeps shutting down and often will not come on after it has been cooled down. The red l...
(Posted by holtster 13 years ago)
The Red Indicator For The Lamp Is On On My A100 Hitachi Projector. Why?
The projector was turned on and about 6 seconds later the door closed and the red lamp light came on...
The projector was turned on and about 6 seconds later the door closed and the red lamp light came on...
(Posted by holtster 13 years ago)