Hayward Super Pump Support Question
Hayward Super Pump Support Question
Find answers below for this question about Hayward Super Pump.Need a Hayward Super Pump manual? We have 2 online manuals for this item!
Question posted by reedernancy on June 10th, 2013
Need Side Outlet To Replace Broken Pool Pump
Have an older model of the SP15801x15 1 1/2 HP that I need to replace. It connects through a side outlet into my pool pump so need one with side and not top outlet. What is that model number and where do I buy it?
Current Answers
Related Hayward Super Pump Manual Pages
All Super Pump models - Page 1
...
INSTALLATION, OPERATION, & PARTS
*50HZ Models are not UL or CSA Listed. This product should be installed and serviced only by a qualified professional. HAYWARD POOL PRODUCTS, INC.
620 DIVISION STREET ELIZABETH, NJ 07207 (908) 351-5400 WWW.HAYWARDPOOL.COM
WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
P/N: ISSPSERIES REV. Super Pump™ Series
The Hayward...
All Super Pump models - Page 2
...of the motor. Pool and spa components have a finite life. All components should always be readily disassembled for personal injury. Super Pump ™ Series ____...pump is intended for outdoor use, it rains. Though this product is strongly advised to the pool. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Basic safety precautions should be inspected frequently and replaced...
All Super Pump models - Page 3
...connect unit to GFCI. Hazardous voltage can become entangled in an opening of a suction outlet sump or suction outlet cover that licensed electricians do NOT use pool or spa if any suction outlet component is damaged, broken...
Hair Entrapment- Mechanical Entrapment- Super Pump™ Series _____ _____
_____
_____
Page 3 of the limb. Risk of swimming pool, spa, or hot tub. All ...
All Super Pump models - Page 4
... MUST be removed,
without disturbing pipe or mounting connections, by disengaging just four (4) bolts. Failure to...REPLACEMENT PARTS Pool and spa water circulation systems operate under
hazardous pressure during pump start -up . Stand clear of pump components. Before servicing pool and spa...when the basket needs cleaning. ƒ All components molded of the Hayward Super PumpTM Series. Failure...
All Super Pump models - Page 5
...pump in line. This product should allow any plumbing fittings. Pump mount must: ƒ Allow pump inlet height to reduce friction loss. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Pump Location
Locate pump...]
[317]
[2.44]
[90]
[698]
[2.44]
IMPORTANT NOTES -
Super Pump ™ Series__________
Product Specifications
_____
Page 5 of air for gate valves in...
All Super Pump models - Page 6
...pump suction and outlet ports have molded-in pool (multiple drains) or double suction (skimmer and main drain). do NOT over-tighten fitting or you face the open end of the fitting, beginning at least two suction outlets).
All wiring must be performed by a licensed electrician, and MUST conform to seal threaded connections on electrical connections...Pool and spa... REPLACEMENT PARTS Pumps,...
All Super Pump models - Page 7
... suction and outlet pipes. 3. In case of a power outage, check GFCI for all metal parts within 5 ft. (1.5 m) of inside walls of swimming pool, spa, or hot tub. Reset if necessary. NEVER run pump dry. Do NOT add chemicals to , grounding, bonding and general wiring procedures.
WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Instructions...
All Super Pump models - Page 8
....
Failure to do so could result in your pool/spa system. If water
source is lower than the pump, pump will depend on filter, when starting pump.
See Troubleshooting Guide.
No lubrication is primed.
Use only a low pressure (below ). ATTENTION -
WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS See filter owner's manual. ƒ If water...
All Super Pump models - Page 9
...Replace motor cover to tap seal out. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump ™ Series Storing Pump...replacement. Do not use this manual for swimming pool pump installation. Remove the four (4) 3/8" x 2" housing cap screws which hold the motor assembly to the pool... Once the pump is now exposed. Failure to pump before draining pump.
WARNING -...
All Super Pump models - Page 10
... seat and press it firmly and evenly into pump/strainer housing, being careful not to pump/strainer housing using the two (2) hex shaped screws. Replacing the Impeller and Diffuser (See Parts Diagram on...the two (2) guides. Slide the motor assembly with a dilute solution of the seal plate -
Super Pump ™ Series
Page 10 of 15
Seal Installation (See Parts Diagram on page 11 of the...
All Super Pump models - Page 11
Super Pump ™ Series
Replacement Parts
Parts Diagram
Page 11 of 15
Parts Listing
PART NUMBER
REFERENCE NUMBER
DESCRIPTION
NUMBER MODEL
MODEL
MODEL
MODEL
MODEL
MODEL
REQUIRED SP2600X5 SP2605X7 SP2607X10 SP2610X15 SP2615X20 SP2621X25
1
HAND KNOB
2
SWIVEL NUT
2
SPX1600P SPX1600P SPX1600P SPX1600P SPX1600P SPX1600P
2
SPX1600N SPX1600N SPX1600N SPX1600N SPX1600N SPX1600N
3...
All Super Pump models - Page 12
... jammed with water. Empty pump/strainer housing. Lubricant will not prime if there are tight. Loose connections on pool wall. 3. Leaks will ...pump does not develop a vacuum and pump has sufficient "priming water": i. Check if all connections, circuit breakers, and fuses. iv. Low Flow - WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Improper or loose wiring connections...
All Super Pump models - Page 13
...replace cartridge. 4. Air leak in pool, and unrestricted discharge return lines. Vibration due to the equipment pad. 3. Solution: Re-tighten using Teflon tape. 5.
Solution: Clean the pump housing. 4. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT...: (cont'd.)
2. Super Pump ™ Series
Page 13 of filter, valve partially closed (high gauge reading). Undersized...
All Super Pump models - Page 14
...
Hayward Pool Products, Inc. 620 Division Street Elizabeth, NJ 07207
▲Retain this pump, Hayward Pool Products, Inc., 620 Division Street, Elizabeth, New Jersey, warrants its pump housing/...purchase. To obtain warranty replacements or repair, defective components or parts should be free from state to state.
*Supersedes all previous publications. Super Pump ™ Series
___ Page...
All Super Pump models - Page 15
... Registration Card
Name Address City State_________ Zip E-mail Address
Product Purchased Product Serial No
□ New Installation
□ Replacement
Type of In-Ground Pool:
□ Vinyl □ Fiberglass □ Gunite
Size of purchase/installation. Super Pump ™ Series
___
Page 15 of 15
▼DETACH HERE: Fill out bottom portion completely and mail within...
Parts Guide - Page 1
...model and H.P.:
-
Hd.
SPX2615CKIT* - 2 H.P.
Qty.
1
SPX1600AA
Pump Housing/Strainer, 1 1⁄2" x 1 1⁄2", with Drain Plugs
1
1
SPX1620AA
Pump Housing/Strainer, 2" x 2", with an "SP1600X-" part number...the kits are not available. Pumps
Super Pump®
SP1600X PUMP SERIES (MAX-RATED) REPLACEMENT PARTS
Parts for Pump Models: SP1600X5, SP1605X7, SP1607X10, ...
Parts Guide - Page 2
..., for 1 1/2 H.P.
17
SPX2615C
Impeller, for 2 H.P.
17
SPX1621C
Impeller, for Pump Models: SP2600X5, SP2605X7, SP2607X10, SP2607EE(2S), SP2610X15(2S), SP2615X20(2S), SP2621X25
4
6
5
7
16 13
11 12 14 18
17 10
8
2 3 15
9
1
Ref.
Pumps
Super Pump®
SP2600X PUMP SERIES (MAX-RATED) REPLACEMENT PARTS
Parts for 2 1/2 H.P.
18
SPX1600Z1M
Motor, 1/2 H.P., Threaded Shaft (Single...
Similar Questions
How To Wire Pool Pump With Integral Timer And Salt Water Chlorinator?
Pool pump + salt chlorination system.I am replacing a conventional pool pump with a Hayward EcoStart...
Pool pump + salt chlorination system.I am replacing a conventional pool pump with a Hayward EcoStart...
(Posted by jdkroeger 7 years ago)
My Outlet Port On My Pool Pump Is Cracked What To Do
(Posted by Slbeau 10 years ago)
How To Rebuild Hayward Pool Pump Model C48k2n143b1
(Posted by hertskit 10 years ago)