Hayward Super II™ Support Question
Hayward Super II™ Support Question
Find answers below for this question about Hayward Super II™.Need a Hayward Super II™ manual? We have 1 online manual for this item!
Question posted by Timandandrea2003 on July 13th, 2014
Not Enough Pressure
The motor turns on just replaced 3 ring kit and it still does not build enough pressure to flow through the filter or run the pool shark
Current Answers
Related Hayward Super II™ Manual Pages
All Super II models - Page 1
... MUST complete, in full, all electrical installations noted in -ground swimming pool/spa that will provide many years of efficient, dependable, corrosion-free service. ATTENTION INSTALLER - WARNING -
The Hayward Super II Pump is equipped with large capacity filters, heaters, and pool cleaning equipment.
THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, OPERATION...
All Super II models - Page 2
...pools and may result in this
owner's manual and on your pump or in a building such that are important but not related to prevent children from the weather. WARNING - Failure to follow instructions may also be positioned to hazards.
Super II... equipment, turn power supply OFF.
Pool and spa components have a finite life.
WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD ...
All Super II models - Page 3
...pool, spa, or hot tub. Suction Entrapment Hazard. A pressure applied to , grounding, bonding and other equipment. A negative pressure applied directly to
prevent abuse from external bonding lug to the following entrapment hazards:
Hair Entrapment- The maximum system flow... shall not be caught in suction outlet cover. Super II™ Pump Series __________
_____
Page 3 of ...
All Super II models - Page 4
... MAXIMUM. ƒ All components molded of the Hayward Super II Pump Series. Failure to the pool.
Motor and entire drive group assembly can cause fires, which could cause property damage, severe personal injury, or death. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Before servicing pool and spa water circulation system, all system and pump controls...
All Super II models - Page 5
... be as close to pool as practical and run suction lines as direct as possible. ƒ Allow use , it rains.
Select a well-drained area, one that will not flood when it is recommended that a minimum length of short, direct suction pipe (to protect the electrical components from the weather. Super II™ Pump Series__________...
All Super II models - Page 6
... dangerous or fatal electrical shock, turn OFF power to electrical power supply.
All electrical wiring MUST be new or thoroughly cleaned before
working on molded plastic components. Use copper conductors only. Super II™ Pump Series __________ Pump Mounting (cont'd)
_____
Page 6 of a
swimming pool filtration system operate under pressure. All plastic fittings must be...
All Super II models - Page 7
... ground and disconnect power before starting motor. Ensure all wiring standards including, but not limited to pool users. Super II™ Pump Series __________
_____
Page 7 of 14
Electrical (cont'd.)
Voltage
Voltage at full load, consult Power Company. Running pump dry may overheat, causing overload tripping and reduced component life. Run pressure test for tripping, which could...
All Super II models - Page 8
Super II™ Pump Series
Page 8 of pump suction. Do NOT add chemicals to pool/spa system directly in severe personal injury.
ƒ Release all suction and discharge valves are open when pump is necessary. ƒ Keep motor clean. See filter
owner's manual for pump to prime, which may take up to Start-Up (cont'd.)
ATTENTION - fill...
All Super II models - Page 9
....COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Failure to motor
before beginning shaft seal replacement. B. Contact your pool/spa system.
Removing the Motor Assembly (See Parts Diagram on...in the system. D. Super II™ Pump Series
Storage/Winterization
Page 9 of the pump/strainer housing, exposing the diffuser.
WARNING - ATTENTION - Keep motor dry and covered during ...
All Super II models - Page 10
...polished surface facing away from turning.
5. Replacing the Impeller and Diffuser (See Parts Diagram on page 11 of this manual for pump component locations.)
3.
Super II™ Pump Series
Page ...the cap covering the motor shaft. Replace motor cover to tap seal out. Removing the Ceramic Seat (See Parts Diagram on the motor shaft). Place the impeller ring back onto the impeller,...
All Super II models - Page 11
Super II™ Pump Series
Replacement Parts
Parts Diagram
Page 11 of 14
Parts Listing
WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
All Super II models - Page 12
... o-ring is felt, check for line blockage. Be sure to check by undersized wiring or extension cord use). Solution: Contact a qualified repair professional.
Re-check strainer housing cover and all threaded connections for free movement and lack of motor shaft for suction leaks. Remove and replace shaft seal only if it if necessary. Super II...
All Super II models - Page 13
Super II™ Pump Series
Page 13 of filter, valve partially closed (high gauge reading). clean or replace cartridge. 4.
Vibration due to the equipment pad. 3. Solution: Clean the pump housing. 4. PRODUCT REGISTRATION
(Retain For Your Records)
DATE OF INSTALLATION
INITIAL PRESSURE GAUGE READING (CLEAN FILTER
PUMP MODEL HORSEPOWER
FILTER MODEL
SERIAL NUMBER...
All Super II models - Page 14
...days of the receipt of the standard warranty apply. Super II™ Pump Series
___ Page 14 of this pump, Hayward Pool Products, Inc. warrants its products free from state... delays. The Hayward Pool Products warranty does not apply to be repaired or replaced, at our option, without charge, within 10 days of Pool
□ Pump □ Filter □ Automatic Pool Cleaner □ Light...
Similar Questions
How Do You Remove The Pump From The Motor
how do you remove the pump from the motor
how do you remove the pump from the motor
(Posted by nowak1294 10 years ago)
Hayward Super Iiâ?¢ How Many Horsepower Is Model K48l2n104
(Posted by bhochner 10 years ago)
I Have A 12 Yr Old Hayward Pool Pump That No Start. No Hum.
I have a 12 yr old hayward pool pump that does not start or even hum. I opened the back cap and test...
I have a 12 yr old hayward pool pump that does not start or even hum. I opened the back cap and test...
(Posted by zipster57858 11 years ago)