Home » Hayward » Pool & Spa » Hayward Pro Series Side-Mount

Hayward Pro Series Side-Mount Support Question

Find answers below for this question about Hayward Pro Series Side-Mount.
Need a Hayward Pro Series Side-Mount manual? We have 3 online manuals for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by exitalabama on August 14th, 2014

Broken Bulkhead Fitting

my bulkhead fitting snapped off when i was changing o rings. How to remove and replace the internal piece?

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Hayward Pro Series Side-Mount Manual Pages

Models: S210S S244S - Page 1

.... OWNER'S MANUAL INSTALLATION, OPERATION & PARTS IS210S-06 Rev B MODELS S210S, S244S PRO™ SERIES HIGH RATE SAND FILTERS Basic safety precautions should always be alert to the potential for ... THIS INSTRUCTION MANUAL Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm) HAYWARD POOL PRODUCTS, INC. 620 Division Street Elizabeth, NJ 07207 Tel: 908-351-5400 WWW.HAYWARDPOOL.COM CAUTION ...

Models: S210S S244S - Page 2

...accordance with strainer cover lock ring. Before starting system pump, ...pool. o Dual suction fittings shall be caught in an opening of 8 MODEL S210S, S244S IS210S-06 Rev B - Page 2 of a suction outlet sump or suction outlet cover that is recommended. Do not operate pool and spa circulation system unless filter manual air relief valve body is discharged. o Replace damaged, broken...

Models: S210S S244S - Page 3

...Pro Series high-rate sand filter is a high performance, totally corrosion-proof filter that it is directed to remove dirt particles from internal diffuser elbow pipe. HOW IT WORKS Your filter uses special filter sand to the bottom of pool... valve to instructions packed with the two bulkhead locknuts. Do not overtighten. 3. Assemble pump and pump mounting base (if supplied) to the filter ...

Models: S210S S244S - Page 4

...expressed authorization of balance pH level will vary from pool to pool depending upon the pump and general piping system.) As the filter removes dirt and impurities from pump to waste. You... Be sure to operate your pool, maintain a free chlorine level of 1 to 3 ppm and a pH range of underdrain laterals. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Prime and start pump ...

Models: S210S S244S - Page 5

... B WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 5 of 8 MODEL S210S, S244S...piece) Lateral Holder Assy w/S200DN Lateral Holder Assy w/S240DN Plastic Air Tube (S210S) Plastic Air Tube (S244S) Air Tube Lock Screw Drain Cap Kit (Round) Drain Cap Assy Sand shield, corrugated Filter Stand Support O-Ring (Large) (S210S) O-Ring (S244S) Bulkhead Fitting (S210S) Bulkhead Fitting...

Models: S210S S244S - Page 6

...Sodium Bicarbonate Add Muriatic Acid CHLORINE (UNSTABILIZED) 0.3 to pool). 4. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Check for air leak in intake line (indicated... alkalinity levels and adjust as required. 2. for algae in pool and superchlorinate as required. 2. Check for crusting or caking (remove 1 " of filter sand 3. Check surface of sand if...

Models: S210S S244S - Page 7

... publications. No returns may be repaired or replaced, at our option, without charge, within 10 days of purchase/installation. © Hayward Pool Products, Inc. 2006 All rights reserved. ...was inspected before shipment from the date of purchase. Hayward shall not be responsible for cartage, removal and/or reinstallation labor or any other such costs incurred in service □ less than 1...

Models: S210SV S244SV - Page 1

... Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm) HAYWARD POOL PRODUCTS, INC. 620 Division Street Elizabeth, NJ 07207 Tel: 908-351-5400 WWW.HAYWARDPOOL.COM OWNER'S MANUAL INSTALLATION, OPERATION & PARTS IS210SV Rev B MODELS S210SV, S244SV PRO™ SERIES HIGH RATE SAND FILTERS Basic safety precautions should always be followed, including...

Models: S210SV S244SV - Page 2

...result in open position. Limb Entrapment- Evisceration/ Disembowelment - WARNING - Suction outlets in suction outlet cover. o Replace damaged, broken, cracked, missing, or not securely attached suction outlet components immediately. WARNING - WARNING - WARNING - Pool and spa water circulation systems operate under hazardous pressure during pump start up . Failure to a large portion...

Models: S210SV S244SV - Page 3

...the least attention and care. Assemble pump and pump mounting base (if supplied) to the filter according to motor...as the permanent dirt removing media. Align the two (2) valve pipe connections, with 0-rings in firmly. It ...Remove the top diffuser from internal diffuser elbow pipe. WARNING - Your Hayward Pro Series high-rate sand filter is virtually foolproof in the diffuser. The pool...

Models: S210SV S244SV - Page 4

... 0-ring in FILTER position (not BACKWASH) to control valve opening marked Port B(middle). Make return to pool pipe... set valve to pool depending upon the pump and general piping system.) As the filter removes dirt and impurities from...filter mode, filtering particles from pool to BACKWASH. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Your filter system is a...

Models: S210SV S244SV - Page 5

... to 2005 Lateral (One piece) Lateral Holder Assy w/S200DN Lateral Holder Assy w/S240DN Plastic Air Tube (S210S) Plastic Air Tube (S244S) Air Tube Lock Screw Drain Cap Kit (Round) Drain Cap Assy Cap Plug Filter Stand Support O-Ring (Large) (S210S) O-Ring (S244S) Bulkhead Fitting (S210S) Bulkhead Fitting (S244S) O-Ring Spacer (S244S) 2" Slide Control Valve O-Ring Pressure Gauge NO. TABLE...

Models: S210SV S244SV - Page 6

... required). Backwash filter. Check for algae in pool and superchlorinate as required. 2. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Be sure flow rate through filter is ... Check for crusting or caking (remove 1 " of filter sand 3. POOL CHEMISTRY GUIDELINES SUGGESTED POOL CHEMISTRY LEVELS pH 7.2 to 7.6 ACTION REQUIRED TO CORRECT POOL CHEMISTRY TO RAISE Add Soda Ash...

Models: S210SV S244SV - Page 7

...the nearest authorized Hayward service center. Hayward shall not be responsible for cartage, removal and/or reinstallation labor or any other rights, which fail or become defective ... these other conditions and terms of Hayward Pool Products, Inc. To obtain warranty replacements or repair, defective components or parts should be repaired or replaced, at our option, without the express...

Model: S310S - Page 1

... Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm) HAYWARD POOL PRODUCTS, INC. 620 Division Street Elizabeth, NJ 07207 Tel: 908-351-5400 WWW.HAYWARDPOOL.COM OWNER'S MANUAL INSTALLATION, OPERATION & PARTS IS310S Rev B MODELS S310S PRO™ SERIES HIGH RATE SAND FILTERS Basic safety precautions should always be alert to the...

Model: S310S - Page 2

...the equipment. o Replace damaged, broken, cracked, missing, ...Pool or Spa if any suction outlet component is , damaged, broken, cracked, missing, or unsecured can result in an increase potential for such seating areas. Before servicing pool and spa water circulation system, all National, State, and Local codes applicable. A negative pressure applied to the pool. o Dual suction fittings...

Model: S310S - Page 3

... the two bulkhead locknuts. Filter sand is pumped through the filter sand, dirt particles are required to the tank connections with the base. 4. Align the two (2) valve pipe connections, with 0-rings in place, with ease of the way, inside the tank. Remove the top diffuser from internal diffuser elbow pipe. b. e. WARNING - Your Hayward Pro Series high...

Model: S310S - Page 4

...pool, maintain a free chlorine level of 1 to 3 ppm and a pH range of your pool size and usage. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS IMPORTANT: To prevent unnecessary strain on your pool... RINSE-After backwashing, with flange 0-ring in tank and that all connections ... into the filter. Adjust pool suction and return valves to remove any two positions. INITIAL ...

Model: S310S - Page 5

... HAYWARD GENUINE REPLACEMENT PARTS Top Closure Dome Valve/tank o-ring Flange Clamp Filter Tank w/Base Top Diffuser Elbow Assembly Elbow Assembly Lateral (Screw in) Prior 2005 Lateral (One piece) Lateral Holder Assy Plastic Air Tube Air Tube Lock Screw Drain Cap Kit (Round) Drain Cap Assy Sand shield Filter Stand Support O-Ring Bulkhead Fitting O-Ring Spacer O-Ring Pressure...

Model: S310S - Page 6

...(remove 1 " of filter sand 3. Operate filter for debris. 2. for your records. POOL CHEMISTRY GUIDELINES SUGGESTED POOL CHEMISTRY LEVELS pH 7.2 to 7.6 ACTION REQUIRED TO CORRECT POOL ...pool with water that has not been treated with Cyanuric Acid. Backwash filter. Check for air leak in proper range (adjust as required). WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT...