Hayward CAT-2000 Support Question
Hayward CAT-2000 Support Question
Find answers below for this question about Hayward CAT-2000.Need a Hayward CAT-2000 manual? We have 1 online manual for this item!
Current Answers
Answer #1: Posted by Odin on December 4th, 2017 7:45 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,630
Member since:
April 10th, 2010 Points: 41,236,630
Related Hayward CAT-2000 Manual Pages
CAT 2000 - Page 1
CAT 2000
AUTOMATED CONTROLLER
OWNER'S MANUAL
INSTALLATION OPERATION
MAINTENANCE SPECIFICATIONS
CAT 2000 - Page 2
... local health department regulations. Physically, installation of the pool or spa to be used to eliminate pressure from the CAT 2000 line of the art microprocessor-based design technology to ... down-time.
ALL RIGHTS RESERVED Improper installation may void the warranty and create unnecessary hazards.
Although CAT controllers are relatively simple to install, please take the time to...
CAT 2000 - Page 3
... Automation with the CAT 2000 Components of a CAT System Important Safety Information. Section 14. Section 4. Packaging Contents Standard Installation Installation Utilizing Bypass Line Preparing Pool or Spa Water Chemistry Setting and Operating the CAT 2000 Advanced (Dealer) Setup Mode Display Functions Maintenance Troubleshooting Specifications Warranty
Section 1. Section 2.
CAT 2000 - Page 4
... monitors pH and sanitizer activity, constantly adjusting the feeding of chemical usage and costs. CHEMICAL AUTOMATION WITH THE CAT 2000
A pool operator typically checks and adjusts pool or spa water chemistry hourly at best. The results include elimination of "human error", accurate and reliable maintenance of chemical levels twenty-four hours a day, compliance with ...
CAT 2000 - Page 5
... detected. The Flow Sensor (required) monitors the rate of equipment, and damage to maintain pH 7.5. The CAT 2000 controller unit scans and interprets the signals from the factory to the pool or spa surface can occur. The CAT 2000 controller is preset from the pH and ORP probes, displays water quality readings in digital format, and...
CAT 2000 - Page 7
...BNC Connector
(2) BNC Connector Protective Covers (Remove to remove contents. Do not use a razor or sharp instrument to Connect Sensors)
(2) Sensor Storage Containers
(1) CAT 2000 Owner's Manual
The CAT 2000 Pro-Pack includes the following additional items: (1) PVC Backboard with Mounting Holes and Stainless Hardware (1) Machined Acrylic Flow Cell assembled with:
(3) 1/4" NPT x 3/8" Tubing...
CAT 2000 - Page 8
... flex tubing to 6" length of 30'.
INSTALLATION WITH FLOWCELL
The following criteria:
A.
We recommend using a CAT Flowcell and fittings to pool or spa operator. Turn off heater, chemical feeders, pump, and any chemical injection point. Relieve pressure from pool or spa. B. Drill and tap a 1/4" NPT port at a location just down-stream of ten feet from...
CAT 2000 - Page 9
... the controller, install according to Suction)
Rotary Flow Sensor
Flow Flow
Chemical Pump
CAT CO2 or
pH Control
Flow Cell / Flow Sensor Bypass Line Flow
Solenoid
Flow
WASTE...Connect chemical feeders to the controller unit as labeled.
12. CAT 2000 INSTALLATION DIAGRAM WITH FLOWCELL
pH Sensor
CAT 2000
ORP Sensor
CAT 2000 CONTROLLER
Chemical Pump
Influent (to Return Line)
Main Drain and...
CAT 2000 - Page 10
...from filtration system.
2.
ALL RIGHTS RESERVED Securely mount the CAT 2000 controller on bypass inlet and effluent immediately adjacent to Illustration...in Illustration 3.
9. The CAT Flowcell provides a controlled flow to the pump and the return line upstream from heater as shown in -line filter (optional) immediately downstream from pool or spa. Construction of Rotary Flow Sensor...
CAT 2000 - Page 11
... be used to the controller unit as labeled.
16. never cut or splice sensor cables.
14. CAT 2000 INSTALLATION DIAGRAM WITH BYPASS LINE
CAT 2000
CAT 2000 CONTROLLER
Chemical Pump
pH Sensor Sensor Adaptor
ORP Sensor Sensor Adaptor
Chemical Pump
CAT CO2 or
pH Control
Solenoid Flow Cell / Flow Sensor Bypass Line (Plumbed On-Site)
Flow Flow...
CAT 2000 - Page 12
... up the CAT 2000. The ORP setpoint will need to be tested and adjusted prior to provide consistent sanitizer residual levels rather than consistent control of ORP. ALL RIGHTS RESERVED MAXIMUM
7.8 3 4 100 120 400
The above table indicates generally accepted guidelines. Although ORP is to initiating automated control of the pool or spa.
PREPARING...
CAT 2000 - Page 13
...pH channel of the controller may be calibrated as follows:
1. Calibrating pH Readings from the CAT 2000 are ready to set your selection, then press the Hidden Button (#1) again to return to...the normal operating mode after twenty seconds, storing any changes. SETTING AND OPERATING THE CAT 2000
Once desired start up chemistry parameters have been established, you must select base feed mode...
CAT 2000 - Page 14
... level by the controller. 3. The chemical feeder will operate continuously for safe drinking water. Changing the ORP Setpoint The CAT 2000 is preset from the factory to maintain pH at 7.5. Manually test pool or spa to confirm that the current sanitizer reading (chlorine, bromine, etc.) is the generally accepted world standard for 30 minutes...
CAT 2000 - Page 15
... Mode Selection Button (#5) until the red "OFF" LED is illuminated. The chemical feeder will not be interrupted for approximately ten seconds.
About Proportional Feed The CAT 2000 features an advanced proportional feed algorithm which constantly analyzes demand for approximately ten seconds. The chemical feeder will be disabled.
Automatic pH feeding will operate...
CAT 2000 - Page 16
... Adjustment Button
5
pH Channel Mode Selection Button
6
ORP Channel Increase Button
7
ORP Channel Decrease Button
8
ORP Channel Setpoint Adjustment Button
9
ORP Channel Mode Selection Button
CAT 2000
pH/ORP AUTOMATED CONTROLLER
FEED
p1H
ALARM
2
3
SETPOINT ADJUSTMENT
4
SET
CALIBRATE
ORP FEED
ALARM
6
7
SETPOINT ADJUSTMENT
8
SET
pH FEED MODE
5
AUTO OFF MANUAL
ORP FEED...
CAT 2000 - Page 17
Advanced (Dealer) Setup Options
Beginning with the 2008 model year, the CAT 2000 controller incorporates an advanced programming menu and enhanced features.
Press the Up (#6) and Down (#7) arrow buttons to activating both channel Alarm indicators and sounding the ...
CAT 2000 - Page 22
... Alarm (Beeper)
bPr The Beeper setting allows the audible alarm to make a hard-copy record of both channels. The CAT Serial Printer prints one data record at 15 minute intervals. Demonstration Mode
dEo Places the controller in Demo Mode for showroom... the feed output and alarm status of controller operating parameters. Serial Interface
Srl The CAT 2000 includes a standard Rs232 serial interface.
CAT 2000 - Page 23
...LED is illuminated when pH is manually activated. Please note that for enhanced viewing the CAT 2000 features a "dead-front" display panel, so only illuminated indicators will be displayed....LED is illuminated whenever the controller is available. pH Alarm Indicator (#2) Illumination of the pool or spa water (as calibrated) passing through the filtration system. SECTION 10. pH Manual Off...
CAT 2000 - Page 26
It is important to note that changes in pool or spa water, the sensors may also be clean and ...
CAT 2000 CONTROLLER The CAT 2000 controller unit is important to maintain total alkalinity on bather load and other facilityspecific characteristics.
Slow response, increased need of additional or alternative sanitizers will damage the reference junction and void the sensor warranty...
CAT 2000 - Page 31
.... No representative has authority to change or modify this warranty is limited to the following address:
Hayward Commercial Pool Products 10101 Molecular Drive Suite 200 Rockville, MD 20850 ...is found to be defective upon examination.
SECTION 14. WARRANTY
LIMITED WARRANTY
Hayward® warrants the CAT 2000 automated controller to be directed to the repair or replacement of ...
Similar Questions
My Orp Side On My Cat 2000 Is Only Putting Out 5.6 Volts Instead Of 120. What Is
the orp side on my cat 2000 is only putting out 5.6 volts so it's not causing the center pump to run...
the orp side on my cat 2000 is only putting out 5.6 volts so it's not causing the center pump to run...
(Posted by bobsteele 1 year ago)
Ph Reads 26 An Cat 2000 And 7.2 With Chemicals And Test Strips.
Ph On Cat 2000 Is 26. Is 7.2 On Test Strip And With Chemicals
Ph On Cat 2000 Is 26. Is 7.2 On Test Strip And With Chemicals
(Posted by michael51382 1 year ago)
How Do You Keep A Cat 2000 From Turning Itself Off
How do you get a cat 2000 controller from turning itself off when the number becomes to low
How do you get a cat 2000 controller from turning itself off when the number becomes to low
(Posted by Ryelee11 2 years ago)
I Recently Lost Power, Now My Ecommand 4 Panel Will Not Turn My Pump On.
I can only turn the pump on and off with the panel breaker. The panel is no longer controlling the p...
I can only turn the pump on and off with the panel breaker. The panel is no longer controlling the p...
(Posted by karenmonroelvnv 9 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)