Hayward Aqua Rite Salt Chlorination Support Question
Hayward Aqua Rite Salt Chlorination Support Question
Find answers below for this question about Hayward Aqua Rite Salt Chlorination.Need a Hayward Aqua Rite Salt Chlorination manual? We have 6 online manuals for this item!
Question posted by cathyvmabe on August 9th, 2012
The Generating Light Is Off; No Flow Light Is On,
We checked the lines, the ph is low and the stabilizer is low. Is there a way to get the chlorine flow generating again. Is the lines and switch the only solution.
Current Answers
Related Hayward Aqua Rite Salt Chlorination Manual Pages
AQ-RT-PRO Oct 08 & later - Page 4
...sodium chloride after killing bacteria. Check local codes for your authorized Goldline dealer. Aqua Rite Pro chlorine generators operating with the optional Goldline AQL-CHEM to provide a fully integrated chemistry solution for other dispensing device requiring 120VAC or 240VAC on the size of your pool.
The models are available from your pool. The Aqua Rite Pro can damage your...
AQ-RT-PRO Oct 08 & later - Page 14
... may need to the factory default values. It usually takes 2-3 adjustments to the amount of chlorine the Aqua Rite Pro will stay off 60 seconds after that entire volume of the summer and down accordingly. Move to generate enough chlorine. to Default Press +
Are you can control which directly contribute to find they have to...
AQ-RT-PRO Oct 08 & later - Page 15
... scale off power to avoid this low temperature cutoff by displaying the message "Inspect/Clean Cell" after cleaning your pool plumbing would. The Aqua Rite Pro automatically stops generating when the pool water temperatures drops below 50ºF. Most pools require less chlorine during cold weather: Check chlorine levels periodically. Maintaining the Aqua Rite Pro System
To maintain maximum...
AQ-RT-PRO Oct 08 & later - Page 17
..., verify that the Aqua Rite Pro installation does not constitute a cross connection with a flow switch and cell unions.
The flow switch and cell should be plumbed in front of the spa during "spa only" operation. The preferred installation is packaged with the local potable water supply. Configurations #2 and #3 allow for chlorination of both the pool and spa during spa spillover operation...
AQ-RT-PRO Oct 08 & later - Page 22
... proper operation
• pH High - The pH probe may need to partially drain the pool and add fresh water.
• Chlorinator Cell Sensor -- Chlor Off -- The Aqua Rite Pro will stop generating chlorine under certain high salt conditions in order to be cleaned or replaced.
• ORP Probe Error -- If the chlorinator cell voltage is detected, check the feeder for more...
AQ-RT-PRO prior to Oct 08 - Page 4
...The operation requires a low concentration of chlorine to provide a fully
integrated chemistry solution for your particular location and circumstances.
The Aqua Rite Pro can also
control pH by converting the salt into free chlorine which kills bacteria and algae in your pool.
OPERATION
The Aqua Rite Pro is an automatic chlorine generation system for immediately adjacent...
AQ-RT-PRO prior to Oct 08 - Page 14
...Light On for 60 sec
Toggle between "Always On" and "On for 60 seconds". Select between Always On and On for your pool/spa...generate enough chlorine. reset Confirmed
Move to previous/next settings menu item
Use this low temperature cutoff by using AQL-CHEM) 3. The Aqua Rite Pro automatically stops generating when the pool...down accordingly. the amount of salt in the recommended range, there...
AQ-RT-PRO prior to Oct 08 - Page 15
...still visible, repeat soaking and rinsing. Most pools require less chlorine during cold weather: Check chlorine levels periodically.
Servicing and Cleaning the Aqua Rite Pro cell
Turn off . Be sure to... only in pools where the water chemistry has been allowed to do not use metal as specified. Winterizing
The Aqua Rite Pro electrolytic cell and flow detection switch will remind ...
AQ-RT-PRO prior to Oct 08 - Page 17
.... Plumbing
Ensure that the arrow on the flow switch (located on page 13. Never use configurations #2 or #3 above to the pool plumbing.
Configurations #2 and #3 allow chlorination of both the pool and spa during spa spillover operation, but prevent overchlorination of the cell. To ensure proper operation, verify that the Aqua Rite Pro installation does not constitute a cross connection...
AQ-RT-PRO prior to Oct 08 - Page 22
... Aqua Rite Pro will stop generating chlorine under certain high salt conditions in order to reset the alarm and resume dispensing.
• pH Calibration Error -- If a pH level of 6.9 or less is detected, check the chemical supply and the feeder for proper operation
• pH Timeout - If a pH level of 950mV or higher is either open or short circuit.
• Low...
AQR - Page 4
... installing this product as part of salt (sodium chloride) in the pool. The operation requires a low concentration of a saline water purification system in your pool. OPERATION
The Aqua Rite® is an automatic chlorine generation system for other restrictions. Check local codes for pool or spa sanitation. The models are low enough that the installation and mounting requirements...
AQR - Page 11
... of chlorine the Aqua Rite will generate: 1. Most pools require less chlorine during cold weather and the "Desired Output %" should only take minor, infrequent adjustments. Because the chlorine demand of the pool increases with temperature, most people find the ideal setting for the next 500 hours.
8 The Aqua Rite salt display and LED indicators operate as normal, but the main switch and...
AQR - Page 14
... diagram on top of gray hex) points in the direction of water flow. Never use configurations #2 or #3 above to the pool/spa. Tighten unions BY HAND for information about available chlorinator cells.
Alternate configurations #1 shows the flow switch can also be in the return line to allow for systems with spillover, use configuration #4.
1
2
12" min
12" min...
AQR - Page 18
... selected (page 7).
Aqua Rite® switch in pool/spa. Desired Output % adjustment setting is at a very high rate and deplete the residual free chlorine. Cold water (below 2400 ppm, Check Salt LED on page 8. It still may be a matter of salt, it is low, add salt according to "normal" and chlorine tests will
use chlorine at recommended levels.
6.
Check salt level in the...
Aqua Rite & Aqua Rite XL - Page 4
...chemistry. The only special requirements for pool or spa sanitation. The operation requires a low concentration of the pool. These reactions will revert back to backwashing, draining, or splashing (not evaporation). OPERATION
The Aqua Rite® is an automatic chlorine generation system for the Aqua Rite are the salt level and stabilizer. NOTE: Before installing this product as...
Aqua Rite & Aqua Rite XL - Page 9
... flow switch has detected no chlorine generation. CHECK SALT When flashing, the salt level is low (below 2700 ppm) and Aqua Rite is greatly reduced and the Aqua Rite has stopped producing chlorine. At the end of purification to be sure to put the Main Switch in the SUPER CHLORINATE position.
Indicator LED's
POWER When illuminated, the Aqua Rite has input power. When flashing, the pool...
Aqua Rite & Aqua Rite XL - Page 10
... as well as how to operate with all of chlorine the Aqua Rite generates. With the temperature displayed, move the main switch from the pool automation display/keypad. When connected to a pool automation control (Goldline Aqua Logic, Pentair Intellitouch or Polaris Eos): The Aqua Rite is designed to add/remove salt. Note: The "Desired Output %" adjustment will not function when...
Aqua Rite & Aqua Rite XL - Page 12
... POWER
ELECTRONIC CHLORINE GENERATOR
G LDLINE CONTROLS INC.
The control must be mounted a minimum of non-copper based algaecide to block the four sides of the control. Do not mount Aqua Rite inside the box), it is important not to the pool, per manufacturer's instructions. FROM FROM POOL SPA
TO
TO
SPA
POOL
Preparing Pool/Spa Water
Refer to the Aqua Rite system. This...
Aqua Rite & Aqua Rite XL - Page 13
... that the Aqua Rite® installation does not constitute a cross connection with spillover, use configuration #4.
1
2
12" min
12" min
3
4
Flow Switch:
IMPORTANT: There must be in front of the spa during spillover but preventing overchlorination when operating the spa only.
10 Configurations #2 and #3 allow chlorination of both the pool and spa during spa spillover operation...
Aqua Rite & Aqua Rite XL - Page 18
... LED illuminated
Remove and inspect the cell for large pools)
- Very warm pools increase chlorine demand--increase Output %, or filter run time.
- High level of Nitrogen in pool/spa. A possible Printed Circuit Board fault has been detected.
"High Salt" LED illuminated
Check salt level in pool water.
- Low stabilizer (Cyanuric Acid).
- Filter pump time too short (8 hours for...
Similar Questions
Check System Light Is On And My Salt Reading Is Wrong.
The check system light is on. I had my water tested and my saltvlevelvwas 3800, but the pro logic sa...
The check system light is on. I had my water tested and my saltvlevelvwas 3800, but the pro logic sa...
(Posted by jtekg4 3 years ago)
Can An Aqua Rite Salt Generator Be Controlled From A Hayward Ecostar
(Posted by krzyJON 10 years ago)
How To Set The Pool Light On My Aqua Plus To Go On An Off
(Posted by pinkyquie 10 years ago)
System Is On (power).
The No Flow Red Light Is On
How Do I Get It To Generate
(Posted by Lionelfournier 11 years ago)
Hayward Swimpure Chlorine Generator Not Working
When power is applied, the red No Flow light starts flashing, but all other lights are dark (includi...
When power is applied, the red No Flow light starts flashing, but all other lights are dark (includi...
(Posted by abitadave 11 years ago)