Harbor Freight Tools 69303 Support Question
Harbor Freight Tools 69303 Support Question
Find answers below for this question about Harbor Freight Tools 69303 - 1-1/2 Horsepower Whole House Water Pressure Booster Pump.Need a Harbor Freight Tools 69303 manual? We have 1 online manual for this item!
Question posted by dobbs800 on October 19th, 2016
Can I Get The Controller For Hydrostar 1 1/2 Hp 69303 Part Number 49
Can I Get The Controller For Hydrostar 1 1/2 Hp 69303 Part Number 49 On Parts List
Current Answers
Answer #1: Posted by Odin on October 24th, 2016 3:35 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,680
Member since:
April 10th, 2010 Points: 41,236,680
You may be confusing us (an independent help site) with Harbor Freight. First try that company: use the contact information here--https://www.contacthelp.com/Harbor%20Freight%20Tools/customer-service. Otherwise, follow the applicable suggestions at this previous answer.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Harbor Freight Tools 69303 Manual Pages
User Manual - Page 1
... shape or form without the express written consent of purchase if product has no number).
Failure to continuing improvements, actual product may not be reproduced in a safe ...; 2011 by Harbor Freight Tools®. Diagrams within this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. ITEM 69303
Visit our website at: ...
User Manual - Page 2
... not use with appropriate measures.
9. Electromagnetic fields in place.
21.
The plug must be protected from running dry.
8.
The pump must have the following : CAUTION
The pump can be connected to any water is danger of 120 V~ at all connections are factors which has been installed according to higher ground.
5. Access by children...
User Manual - Page 3
... the base plate.
4. Installing
1. Secure the Pump to the end of the Pump is 32 feet. The Pump is installed with 1" NPT connections to get wet.
See Figure 1.
5. Do not allow the Pump to be properly supported on either side of the Pump.
2.
Thread the Pressure Control Box onto the water outlet on a level, solid and dry foundation...
User Manual - Page 4
...: Once the system pressure raises above , for the Pump to restart the Pump. Correct the water supply, press the RESET button then turn the Power Switch on the floor. Then press the RESET button and turn the Power Switch on the water supply leading to leak.
8. f. Power
Pump On Overheat
1-1/2 HORSEPOWER
AUTOMATIC BOOSTER PUMP
Restart
NONSUBMERSIBLE PUMP
ITEM 69303 120V~ / 10A...
User Manual - Page 5
....
a. Remove the Filter from inside the pump housing
Dismantle the bottom part of the shaft. 4.
To prevent damage, do not rest the pump on pump. 3.
d. Reassemble in .
Possible Causes
1.
Motor runs hot and 1. Voltage is being supplied to full capacity. overload kicks off water, and change filter cartridge. motor does not run .
Motor runs but no...
User Manual - Page 6
... no serial number, record month and year of the product.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as a reference tool only.
PLEASE READ THE FOLLOWING CAREFULLY
The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as replacement parts. Item 69303
Page 6
For...
User Manual - Page 7
Page 7 ASSEMBLY DIAGRAM
Item 69303
For technical questions, please call 1-800-444-3353.
User Manual - Page 8
... you . We shall in no defect, or that this warranty, the product or part must accompany the merchandise. If our inspection verifies the defect, we will return repaired ... not within the scope of our warranty, then you with transportation charges prepaid. Item 69303 To take advantage of this product is no event be returned to state.
3491 Mission... WARRANTY
Harbor Freight Tools Co.
Similar Questions
Brush Model Number And Size
Hello, I have a Chicago half inch impact gun model number 45252 and I need brushes for this item, co...
Hello, I have a Chicago half inch impact gun model number 45252 and I need brushes for this item, co...
(Posted by wrski 7 years ago)
Handle Control Plate
Just bought a Central machinery Cement Mixer Item 61932. Bought it off e-bay and it is missing a par...
Just bought a Central machinery Cement Mixer Item 61932. Bought it off e-bay and it is missing a par...
(Posted by mtruitt54 7 years ago)
Replacement Part For Chicago 10' Miter Saw
I need to replace the chicago miter saw positive stop lock lever. It cracked on one side. This will ...
I need to replace the chicago miter saw positive stop lock lever. It cracked on one side. This will ...
(Posted by timhightower 7 years ago)
I Need Parts For My Drill
New Drill Broken Handel For Up And Downf
New Drill Broken Handel For Up And Downf
(Posted by egallevaton 7 years ago)
