Harbor Freight Tools 61932 Support Question
Harbor Freight Tools 61932 Support Question
Find answers below for this question about Harbor Freight Tools 61932 - Cement Mixer - 3-1/2 Cubic Ft.Need a Harbor Freight Tools 61932 manual? We have 1 online manual for this item!
Question posted by mtruitt54 on March 4th, 2017
Handle Control Plate
Just bought a Central machinery Cement Mixer Item 61932. Bought it off e-bay and it is missing a part and I don't feel like waiting around for sellers response to this problem. It is missing #41 the Handle control plate. Where might I go to buy this item?
Current Answers
Answer #1: Posted by Odin on March 4th, 2017 8:00 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,660
Member since:
April 10th, 2010 Points: 41,236,660
The first step is to check with the manufacturer: use the contact information here--https://www.contacthelp.com/Harbor%20Freight%20Tools/customer-service; Harbor Tools might just quickly send you the part. Otherwise, ask for a part number and (with or without a part number) follow the applicable suggestions at this previous answer.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Harbor Freight Tools 61932 Manual Pages
User Manual - Page 2
Safety
NOTICE
FOR CEMENT AND MORTAR ONLY.
Addresses practices not related to potential personal injury hazards. It is ...use with Epoxy 2-part resin mix.
Setup
Operation
Maintenance
Page 2
For technical questions, please call 1-888-866-5797.
Item 61932 Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not...
User Manual - Page 3
... kept safe distance from Mixer during assembly.
5. TURN POWER OFF. Page 3 Safety
Setup
NOTICE
FOR CEMENT AND MORTAR ONLY.
This product is in damp or wet locations, or expose them to play with or near this item.
2. Don't use the next heavier gauge. All visitors should be damaged.
7. MAINTAIN TOOLS WITH CARE. REDUCE THE...
User Manual - Page 4
..., excessive heat, and damp or wet areas. Grounded tools require a three wire extension cord. Safety
Setup
Grounding
NOTICE
FOR CEMENT AND MORTAR ONLY.
Do not modify the power cord ...to an electrically "live" terminal. (See 3-Prong Plug and Outlet.)
3-Prong Plug and Outlet
1. Item 61932 If damaged, have a three wire cord and three prong grounding plug. The green wire in accordance ...
User Manual - Page 5
...Cement Mixer when it is unsafe to move the mixer while in close proximity to cause cancer, and birth defects or other construction activities, contains chemicals known [to the State of the following:
a. WARNING: Some dust created by an appropriate standards agency. Operation
Maintenance
Item 61932...Wash hands after handling. (California ...missing, contact Harbor Freight Tools...
User Manual - Page 6
... using vibrating tools regularly or for an extended period should not use with the lowest vibration when there is a choice between different processes.
5. Item 61932 Do not use this manual. Specifications
Electrical Input Motor No Load Speed Drum Speed Drum Capacity Drum Opening
120 VAC / 60 Hz / 3.5 A 1820 RPM 36 RPM 3-1/2 Cubic Feet 15...
User Manual - Page 7
... Turn the Power Switch of the tool off before set up or use ... regarding the parts listed in place. Cotter Pin (1)
Figure C
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. Before Use
Read the ... . See Figure C.
Safety
Setup
NOTICE
FOR CEMENT AND MORTAR ONLY. Assembly/Mounting
1.
Do not use of Bracket axle. Tighten with a ...
User Manual - Page 8
...CEMENT AND MORTAR ONLY. With assistance, set the Lower Drum (48) with attached Arm (77) and Support Bracket Seats (35) into
the Control Handle (46). 13. The Gasket must be flat on the Upper Drum to the Motor Hood. Arm (77)
Figure D
9. Control Handle... Washers (45)
Handle Control Plate (41)
Figure E 11. Item 61932 Use gasket sealer ...14. Position each of Mixer Blades to Support Bracket ...
User Manual - Page 9
... Hex Flange Nuts (5) to secure the Motor to the Motor Bracket.
27. Hand turn correctly. CAUTION! Setup
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. Safety
NOTICE
FOR CEMENT AND MORTAR ONLY.
Adjust Motor location as needed.
29. Check all screws, nuts, and bolts are securely tightened.
Make sure...
User Manual - Page 10
... therein before set up or use with Epoxy 2-part resin mix. Safety
NOTICE
FOR CEMENT AND MORTAR ONLY. Functions
Motor Assembly Mixer Blade
Upper Drum
Control Handle
Stand Wheel Bracket
Wheel
Lower Drum Arm
Leg
Handle Control
Plate
Setup
Operation
Maintenance
Page 10
For technical questions, please call 1-888-866-5797.
Item 61932 Do not use of this product.
User Manual - Page 11
Place the Cement Mixer on the Handle until the desired angle is reached. Block the wheels with Epoxy 2-part resin mix. Flip the switch to the "OFF" (O) position and disconnect the Power Cord.
8.
Setup
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797.
Do not attempt to drain all fluids from the drum...
User Manual - Page 12
...Cement Mixer. WARNING! Replace Belt if damaged according to 3/4".
The belt should deflect anywhere from the Drum Pulley slightly. If the belt deflects too little, loosen the Motor Bracket bolts and lift Bracket upward. Item 61932 If abnormal noise or vibration occurs, have the problem...PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not ... a stiff, long handled bristle brush for cracks...
User Manual - Page 13
...tool and circuit has no -load intervals.
2. If an extension cord is unpowered, turn
off tool and check circuit breaker. Disconnect power supply before service. Setup
Operation
Maintenance
Item 61932... cord.
Safety
Troubleshooting
NOTICE
FOR CEMENT AND MORTAR ONLY. Do not use of motor using compressed air.
3.
Internal damage or wear. Tool operates slowly. Belt too loose ...
User Manual - Page 14
...
Setup
NOTICE
FOR CEMENT AND MORTAR ONLY.
Do not use with Epoxy 2-part resin mix.
Item 61932
Parts List and ...1 1 2 2 2 1 1 2 4 6 4 1 13 2 4 2 1 1 1 1 3
Part
Description
41 Handle Control Plate
42 Hex Bolt M10×70
43 Coil Spring
44 Nut M10
45 Flat Washer 10
46 Control Handle
47 Rubber Handle
48 Lower Drum
49 Bearing Cover, Upper
50 Bearing 6206Z
51 Shaft
52 Nut M8
53...
User Manual - Page 15
Assembly Diagram
NOTICE
FOR CEMENT AND MORTAR ONLY.
Item 61932
For technical questions, please call 1-888-866-5797. Page 15
Note: Some parts are listed and shown for illustration ...5529 73
2 3 21
38 23
50
51
50
77
76
5
78 5
32 48 49
40
35 34
5 55 71
34 28 41
70 55
42 45
Maintenance
29 30
69
5 47
79
47
46
4544 43
Record Serial Number Here:
Note: If product has ...
User Manual - Page 16
... DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS... OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Limited 90 Day Warranty
Harbor Freight Tools Co. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE...
Similar Questions
Sheer Pin On The Cement Mixer?
If there is one, where is this located?
If there is one, where is this located?
(Posted by djholmes0928 1 year ago)
Spare Part From Woodworking Mini Lathe.
Hi. I need to buy a V belt number K 516 from a woodworking mini lathe Central Machinery model 95607....
Hi. I need to buy a V belt number K 516 from a woodworking mini lathe Central Machinery model 95607....
(Posted by fjavierruiz21 1 year ago)
Broken Depth Spring
I need to replace the depth spring part # 41, on my central machinery 5 speed drill press (item #602...
I need to replace the depth spring part # 41, on my central machinery 5 speed drill press (item #602...
(Posted by lindapisney 1 year ago)
Bolts For Mixer?
I'm missing some bolts/screws for 31/2 cubic foot cement mixer. How do I get a complete set of bolts...
I'm missing some bolts/screws for 31/2 cubic foot cement mixer. How do I get a complete set of bolts...
(Posted by chrstphr1grffn 1 year ago)