Harbor Freight Tools 63022 Support Question
Harbor Freight Tools 63022 Support Question
Find answers below for this question about Harbor Freight Tools 63022 - 2 HP Gasoline Auger Powerhead.Need a Harbor Freight Tools 63022 manual? We have 1 online manual for this item!
Question posted by mccannm0128 on September 5th, 2017
Unit Is Real Hot And Smoking.
I bought a new predator gas powered auger from Harbor Freight yesterday. Unit number 63022 2hp motor 52cc. I went to use it today and only got through half of 1 hole and the unit is smoking and is very hot. I mixed 25:1 ratio with stabilizer. 1 gallon of gas was about 5.2 oz of 2cycle engine oil. Should I take it back or is there something I'm doing wrong?
Current Answers
Related Harbor Freight Tools 63022 Manual Pages
User Manual - Page 1
....com Email our technical support at: [email protected]
Email our engine support at: predator@harborfreight.com
When unpacking, make sure that the product is a poison you cannot see...no number). Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of Harbor Freight Tools. This is intact and undamaged. NEVER use OUTSIDE ...
User Manual - Page 2
... Plug Wrench, Screwdriver, 2 Hex Keys 52cc Vertical Single Cylinder 2-stroke Forced air cooled 87+ octane stabilizer-treated unleaded gasoline mixed with 2-cycle oil (see below) 0.3 Gallon 2-cycle oil (designed specifically for mixing with full tank
Sound Level at 3 feet
Bore x Stroke
Compression Ratio
Rotation viewed from PTO
(power takeoff - For warranty information, refer...
User Manual - Page 3
...fire prevention requirements.
4. Gasoline fuel and fumes are ...up .
6.
ITEM 63022
For technical questions, ...Use only lubricants and fuel recommended in this Auger may result in death or serious injury. Read the manual before set up and use...smoke while handling fuel. Operation of this manual cannot cover all instructions.
Safety
WARNING SYMBOLS AND DEFINITIONS This is used...
User Manual - Page 4
... accessories that may be turned off the Auger (and remove safety keys, if available) before starting engine. Accessories that are recommended by Harbor Freight Tools for landscape fabric before use .
26. Do not operate in explosive atmospheres, such as in close proximity to maintain a steady drilling speed.
14. Gasoline-powered engines may get pulled into the Bit...
User Manual - Page 5
... system components, get very hot during use . Dispose of it is a choice between different processes.
4. Repeated or long-term exposure to vibration may affect the Auger's operation. To reduce vibration, maintain the tool as possible (while still keeping safe control of fluids and cleaning materials as possible.
2. Page 5 Do not smoke during use . This enables better...
User Manual - Page 6
... Do not smoke, or allow excess to completely cool.
Only a qualified service technician may adjust parts that is sealed by a qualified repair person using only identical replacement...order. Have the Auger serviced by the manufacturer or distributor. b. Then, remove the spark plug cap from the spark plug.
2. If unreadable or missing, contact Harbor Freight Tools for the fuel...
User Manual - Page 7
...damage the unit. The emission control system for laws or regulations relating to the gasoline. For warranty information, refer to the Engine and any other devices used with ...set up or use of this manual. Running the Engine without treating the gasoline with proper spark arrestor installed.
IMPORTANT! Environmental Protection Agency.
You operate the Auger without the proper...
User Manual - Page 8
ITEM 63022 Safety
Components and Controls
Starter Handle Handle
Power Switch
Fuel Tank Throttle
Choke
Bit
Setup
Operation
Maintenance
Page 8
For technical questions, please call 1-888-866-5797.
User Manual - Page 9
... the Auger.
2. Then gently agitate the container to cool before adding fuel. Replace the Fuel Cap.
7.
If the engine is hot from ignition sources. Remove the Strainer and remove any spilled fuel and allow excess to enter the carburetor, affecting engine performance and/or causing damage. Then replace the Strainer. Do not use gasoline...
User Manual - Page 10
.... Move the Power Switch to prepare the Auger.
Grip the Frame... firmly with the proper amount and type of the Engine gently until the engine starts. Press the Primer three or four times. Keep all bystanders away.
2.
d. Fill the engine with your right hand, grip the Starter Handle of unleaded gasoline and 2-cycle oil mixture. WARNING! ITEM 63022...
User Manual - Page 11
...store the tool in the drilled hole, the Auger will screw into the earth, become stuck, and twist violently. NOTICE
See Long-Term Storage on stable
ground. Setup
Operation
Maintenance
ITEM 63022
For technical ... the Bit to adjust the Auger. 6. The Bit should NOT turn off the Engine.
16. After running the Auger at idle, immediately discontinue using the Auger and contact a qualified service ...
User Manual - Page 12
... Replace Fuel Filter (84) and Fuel Cap Set (94)
Before Each Use
Monthly or every 20 hr. ITEM 63022 If abnormal noise, vibration, or excess smoking occurs, have the problem corrected before performing any doubts about your ability to safely service the Auger or engine, have any inspection, maintenance, or cleaning procedures. Follow all...
User Manual - Page 13
... bolt hole in the center is bent or packed with the pre‑mixed unleaded gasoline/2-cycle oil mixture.
6. Check the Air Filter prior to each use , shut the engine off any dirt and debris. Do not smoke.
1. Do not use solvents. IMPORTANT: Your Warranty is VOID if the Engine's Fuel Tank is hot from use for...
User Manual - Page 14
... ITEM 63022 Clean out debris from end of fuel hangs in the tank.
4. Using a ...When installing a new spark plug, adjust the plug's gap to remove any spilled fuel.
5. Do not smoke.
1. Safety
...Using an incorrect spark plug may damage the engine.
4. Do not pry against the electrode, the spark plug can be replaced. NOTICE: Tighten the spark plug properly. To clean, remove them with clean gas...
User Manual - Page 15
... the Auger is VOID.
5. CLEANING: Wait for storage as water heaters, clothes dryers, and furnaces. Do not smoke.
3. Pull Starter Handle to cool, then clean Engine with gasoline Follow Refer to all metal parts.
2. Page 15
Setup
Operation
Maintenance
ITEM 63022
For technical questions, please call 1-888-866-5797. If the engine is hot from use...
User Manual - Page 16
....
Faulty Power switch. Immediately remove spark plug cap from fuel system. Discontinue using Auger until the...Use fresh 87+ octane stabilizer-treated unleaded gasoline/oil mixture only. Do not use gasoline with more than 10% ethanol used. (E15,
E20, E85, etc.)
4. Use fresh 87+ octane stabilizer-treated unleaded gasoline/oil mixture. Clean out passageways using Auger until the tool...
User Manual - Page 17
... creating vacuum, preventing proper fuel flow.
3. Engine overloaded. 3.
Make sure to operating Auger.
1. Remove Bit from hole and clear
hole of impure or low quality gasoline/oil mixture. Re-gap or replace spark plug. 3. Do not use gasoline with fresh 87+ octane stabilizertreated unleaded gasoline/oil mixture. Fill fuel tank with more than 10% ethanol (E15, E20...
User Manual - Page 18
...system warranty on your engine. Emissions Control System Warranty
Harbor Freight Tools (HFT) is no improper maintenance, misuse, or abuse... may be liable for death, injuries to the United States Environmental Protections Agency's (EPA) emissions requirements in... to the original purchaser that this warranty under normal use of exclusion may elect to conform with a replacement....63022
User Manual - Page 22
Safety
Auger Parts List
Part
Description
1A Hub ... 1 1 1 1 1 1 4
Part
Description
18A Oil Seal
19A Bearing
20A Transmission Shaft
21A Screw
22A Handle
23A Rubber Holder
24A Aluminum Bracket
25A Screw
26A Pin
27A 6" Auger Bit
28A Safety Pin
29A Hex Wrenches
30A Open End Wrench
31A Spark Plug Socket
32A Standard Screwdriver
33A Oil Mixing Container
Qty.
1 1 1 4 1 2 1 6 1 1...
User Manual - Page 23
Page 23 Safety
Setup
Auger Diagram
25a 24a 23a 22a
21a
11a
12a 13a 14a 16a 17a 18a 19a
20a
15a 8a
9a 10a
1a 2a
3a 4a 5a 28a 6a 7a
26a 27a
33a
29a 30a 31a 32a
Operation
Maintenance
ITEM 63022
For technical questions, please call 1-888-866-5797.
Similar Questions
Is This Machine Takes Gasoline With Oil? Or Just Gasoline Itself
(Posted by Pedrozahugo 1 year ago)
A Replacement Tray For A Harbor Freight Tools 62382 - 7 In. 1.5 Hp Bridge Tile
Where can I purchase a replacement tray for the model tile saw listed above? [email protected]
Where can I purchase a replacement tray for the model tile saw listed above? [email protected]
(Posted by danielwprior 1 year ago)
Predator Gasoline Auger Throttle Cable
Where can we find a replacement Predator Gasoline Auger Throttle cable?
Where can we find a replacement Predator Gasoline Auger Throttle cable?
(Posted by kaufmangary 1 year ago)
Looking For Throttle Cable For Predator Auger Model # 63022
Could you please send me a part # for a throttle cable on a predator 63022 Auger.
Could you please send me a part # for a throttle cable on a predator 63022 Auger.
(Posted by MidwestSmallEngine 3 years ago)
Looking For Throttle Cable
I am searching for throttle cable part number for predator item 63022 - 2 HP Gasoline Auger Powerhea...
I am searching for throttle cable part number for predator item 63022 - 2 HP Gasoline Auger Powerhea...
(Posted by dgduren 4 years ago)