Home » Hamilton Beach » Blenders » Hamilton Beach 54614

Hamilton Beach 54614 Support Question

Find answers below for this question about Hamilton Beach 54614.
Need a Hamilton Beach 54614 manual? We have 1 online manual for this item!

Hamilton Beach Overview Questions Manuals Reviews Videos Research

Question posted by Anonymous-169420 on October 3rd, 2021

Cleaning Cutting Assembly

Removing cutting blade assemblyto clean Hamilton beach 54614

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on October 3rd, 2021 8:29 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,598,000

1,100
points

https://manualzz.com/doc/en/3199334/hamilton-beach-54614-user-s-manual

Follow Page 6-9 onwards cleaning+ maintains of the product .

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Hamilton Beach 54614 Manual Pages

Use & Care - Page 2

... in water or other than intended purpose. Do not leave blender unattended while it is switched ON, switch OFF immediately and tighten jar onto cutting assembly. 19. SAVE THESE INSTRUCTIONS! 2 Avoid contacting moving blades accidentally become exposed. 18. To reduce the risk of injury, never place cutting assembly blades on examination, repair or electrical or mechanical adjustment...

Use & Care - Page 3

...cutting assembly as replacement parts. Peak power is the measure of the motor wattage during the first seconds of operation. This is when a blender requires the most . This is a better measure of the blender... on page 4. Optional Accessory Hamilton Beach Stay or Go™ Personal Blending Jar (AC16) may result in damage to the cutting blades, jar, blender and possibly result in the ...

Use & Care - Page 4

... a damp cloth or sponge. Care should be taken when handling the cutting assembly as the blades are very sharp. Filler Cap Lid Jar Dispenser Assembly Spout Cap Gasket Cutting Assembly Spout Cap Storage (bottom of blender) Base Control Knob Control Knob Setting Dispense Smoothie Milkshake Icy Drink Blender Speed 1 2 3 4 4 DO NOT IMMERSE BASE IN WATER. Dry thoroughly. 840155503...

Use & Care - Page 5

... Operate 1. How to Clean" section). NOTE: Blender MUST be necessary to turn the blender ON to dispense the liquid. Always inspect cutting assembly for storage. Set jar into outlet. 2. OPTIONAL: When dispenser is not easily removed, rock gently and lift. Plug cord into place on top of blender base for broken, cracked, or loose blades. Put ingredients in...

Use & Care - Page 6

... before cleaning. Ensure dispenser assembly or spout cap are placed too close to lock into position (reverse of Step 5 above). 8. NOTE: DO NOT remove seal rings from jar. 4. Rinse and dry thoroughly. Do not wash cutting assembly or gasket in hot, soapy water. Carefully remove gasket from cutting assembly. 5. Reassemble cutting assembly and gasket onto jar, and replace jar onto blender...

Use & Care - Page 7

... Foods" section. Rinse and dry thoroughly. Dispenser Assembly Cap Plunger Dispenser Assembly Body Adaptor Seal Rings Troubleshooting PROBLEM Blender leaks. Remove dispenser assembly cap by holding jar and turning cutting assembly counterclockwise. 7 Does not dispense. • Make sure blender is recommended. NOTE: Do not remove seal rings from adaptor. 3. A minimum of...

Use & Care - Page 8

...) or visit hamiltonbeach.com 8 When only crushed ice is operating, remove filler cap from freezer. Continue until ice is crushed to a complete stop between pulses. Place lid on blender jar then Pulse on any of ice cubes to jar. Optional Accessories Hamilton Beach Stay or Go™ Personal Blending Jar (AC16) may be purchased...