GE PV970NSS Support Question
GE PV970NSS Support Question
Find answers below for this question about GE PV970NSS.Need a GE PV970NSS manual? We have 2 online manuals for this item!
Question posted by morrisongary525 on July 16th, 2012
Can I Get A Copy Of The Installation Instructions?
The person who posted this question about this GE product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by bargeboard on July 17th, 2012 9:39 AM
bargeboard
Member since:
May 18th, 2012 Points: 1,201,715
Member since:
May 18th, 2012 Points: 1,201,715
You can view and download the installation instructions from the GE support site here:
Related GE PV970NSS Manual Pages
Quick Specs - Page 1
PV970N
GE Profile™ 30" Wall-Mount Hood
Dimensions and Installation Information (in recirculation mode). Amp Rating 120V 4.1
10-7/8"
*Height ...pv970_30
For answers to 9'7" ceiling heights
(10' in inches) Installation Information: Before installing, consult Use & Care/ installation instructions packed with product for current dimensional data.
Listed by Underwriters Laboratories
Specification ...
Quick Specs - Page 2
...® service, 800.626.2000. Powerful variable speed exhaust system effectively pulls smoke and vapors out of the hood • Cooktop Light - Durable filters can be removed for easy cleaning
and maintenance • Model PV970NSS -
Listed by Underwriters Laboratories
Specification Revised 8/09
220969 Vent connects to duct work through the top of...
Use and Care Manual - Page 1
... Controls 4 Vent Controls 4
Care and Cleaning
Grease Filters 5 Hood Lights 6 Stainless Steel Surfaces 6
Installation Instructions
Installation Preparation 7-13 Vented to the Outside 14-17 Recirculating 18-22
Troubleshooting Tips . . . .23, 24
Consumer Support
Consumer Support 26 Warranty 25
Owner's Manual and Installation
Instructions
PV970
PV976
Write the model and serial numbers here...
Use and Care Manual - Page 2
....
Use an extinguisher ONLY if:
1. Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions
IMPORTANT SAFETY INFORMATION. D. The fire is being switched on "Kitchen Fire Safety Tips"...
TO REDUCE
THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: A. When the service disconnecting means cannot be ...
Use and Care Manual - Page 3
...Installation work and electrical wiring must always be done by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
D. READ AND SAVE THESE INSTRUCTIONS
3 TO REDUCE THE RISK
OF A RANGE... is needed for the size of your hood unless it is specifically
recommended in accordance ...
Use and Care Manual - Page 4
Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions
Using the hood controls. To set the memory: A. C.
These settings ...until temperatures below 60 ˚C/140 ˚F. There are installed. FAN. Press + or - NOTE: There is an audible "beep" each time a button is normal. The hood will cycle back through the settings.
MEMORY/OFF. Press ...
Use and Care Manual - Page 5
...hood usage). To remove:
Pull downward on both locking tab handles to secure the filter.
Locking tab handle
Locking tab handle
Charcoal Filter (for recirculating installation...-see Metal grease filter section.
2. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support
Care and cleaning of the hood.
To replace:
1. Remove the metal filter...
Use and Care Manual - Page 7
... requires
basic mechanical and electrical skills. • Completion time - Approximately 1 to 3 hours • Proper installation is not covered under the Warranty.
CAUTION - Installation Instructions
Chimney Vent Hoods
Questions? PRODUCT DIMENSIONS
10-7/8"
*Height to
Ceiling
13-1/8"
2-1/4"
19-3/4"
29-7/8"
30" Models Require a 30" Wide Opening
10-7/8"
2-1/2"
*Height to
Ceiling...
Use and Care Manual - Page 9
... metal, permanent wiring system, or an equipment-grounding terminal or lead on the hood. Grounding instructions The grounding conductor must be connected to the house wiring in accordance with a ... APPLIANCE MUST BE PROPERLY GROUNDED. Electrical supply These vent hoods must be supplied with 120V, 60Hz, and connected to the installation location as possible in a risk of the equipment-grounding...
Use and Care Manual - Page 14
... cleats
1" x 12" min. mounting support
Centerline of the support to secure to the centerline of the vent hood.
• Locate the template packed with the room side of the centerline.
1 INSTALL FRAMING FOR HOOD SUPPORT
IMPORTANT - Installation Instructions INSTALLATION-VENTED TO THE OUTSIDE
DUCTWORK, WIRING LOCATIONS
Determine the exact location of an 8-1/2" dia. above the bottom...
Use and Care Manual - Page 15
..." 2"
CL
DRILL 2 (TWO) 3/16" PILOT HOLES THROUGH STUDS OR REAR WALL SUPPORT
Horizontal Line
12-1/2" Installation Height
ALIGN BOTTOM EDGE WITH PENCIL LINE
INDICATING BOTTOM OF THE HOOD
31-14772 Printed in place at the top.
Installation Instructions
2 INSTALL HOOD MOUNTING SCREWS
The two upper mounting screws must enter the horizontal support or wall studs. •...
Use and Care Manual - Page 16
...: Do not use U.L. Installation Instructions INSTALLATION-VENTED TO THE OUTSIDE
5 CONNECT DUCTWORK
• Remove shipping tape from the damper. • Install ductwork, making connections
in ...ductwork with sheet metal screws. • Wrap all the connections with the 6 original
screws.
16
WARNING: If house wiring is turned off at the hood...
Use and Care Manual - Page 17
Installation Instructions
7 INSTALL DUCT COVERS
• Remove protective plastic covering.
• Assemble duct covers according to the hood.
17 Lift up the right side of the filter opening. Make sure the filter lock is installed for recirculating purposes. Lower duct cover seat
Duct cover attachment tabs
• Extend the inner duct cover upward to the ceiling...
Use and Care Manual - Page 18
... Wiring Location
5"
CL
Ceiling
WALL VENT IS 27-3/4" MIN. Installation Instructions INSTALLATION-RECIRCULATING
DUCTWORK, WIRING LOCATIONS
• Determine the exact location of the vent hood.
• Locate the template packed with the room side of the studs. Add hood installation height determined on the template. • Install a horizontal support at the mounting screw location.
Use and Care Manual - Page 19
Installation Instructions
2 INSTALL HOOD MOUNTING SCREWS
The mounting screws must enter the horizontal support or wall studs.
• With ...IS 27-3/4" MIN. This bracket will allow anchors to the wall with the 4 assembly screws provided. Drill and install per the fastener supplier's instructions. • Drive screws, by hand, into the fasteners to the duct cover bracket with wood screws and/...
Use and Care Manual - Page 20
... bracket. • Use duct tape to seal duct to the deflector
and at the exhaust outlet. Installation Instructions
INSTALLATION-RECIRCULATING
4 MOUNT THE HOOD
WARNING: 2 people are required to lift
and position the hood onto the mounting screws.
• Lift the hood onto the mounting screws. • If using a wall fastener, make sure the washer
is in...
Use and Care Manual - Page 21
...according to the hood.
21
Slide the upper duct cover into the junction box and replace the cover.
the vent holes
will be provided by the installer. Be sure... holes
intended for recirculating
purposes. Install 2 screws to secure the lower duct cover to application. Installation Instructions
6 CONNECT ELECTRICAL
Verify that power is installed for use U.L. WARNING: If...
Use and Care Manual - Page 22
... the latch on the filter lock to operate the hood. Metal Grease Filter
• Remove the protective film on the grease filter.
• Fit the tabs at the end of the filter into the slots in this manual
to release.
22 Installation Instructions INSTALLATION-RECIRCULATING
8 INSTALL FILTERS
Charcoal Filter Insert the charcoal filter into the...
Use and Care Manual - Page 23
... you call for service...
Fan does not operate when fan + or - See the Installation Instructions for setting the MEMORY/OFF button.
Damper blade on wall or roof cap may not ...) may flip over and will cause improper venting.
Early bulb failure
Replacing bulbs with correct wattage. Hood does not appear The memory feature of duct pipe will not fully open .
•Make sure nothing...
Use and Care Manual - Page 25
...limited to obtain service
under the warranty. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support
GE Range Hood Warranty. All warranty service provided by law. ...succeeding owner for products purchased for home use the product.
■ Improper installation, delivery or maintenance.
■ Failure of merchantability or fitness for service. ...
Similar Questions
Remove And Change Light Bulb On Ge Jvw5301 Range Hood
Page 9 says use a flathead screwdriver to remove ring but does not tell you how to do this. Push, pu...
Page 9 says use a flathead screwdriver to remove ring but does not tell you how to do this. Push, pu...
(Posted by ltindle 6 years ago)
Ge Jvx3300 Range Hood. How Do I Remove The Light Bulb Cover?
There's a little picture showing that you should use a screw driver, but nothing beyond that. I'm af...
There's a little picture showing that you should use a screw driver, but nothing beyond that. I'm af...
(Posted by Dontcallmehowie 7 years ago)
Ge Range
I have a two piece grate on the top of my range. Is it possible to get the grates that allowe for th...
I have a two piece grate on the top of my range. Is it possible to get the grates that allowe for th...
(Posted by anderson0046 9 years ago)
Ge Jvb98shss Vent Control Button
does anyone have the manual to instal this?
does anyone have the manual to instal this?
(Posted by Anonymous-117001 10 years ago)
Need A Manual To Install The Button.. Please Help.
(Posted by Anonymous-117001 10 years ago)