GE NX-148E-RF Support Question
GE NX-148E-RF Support Question
Find answers below for this question about GE NX-148E-RF - Security NetworX NX-8E System.Need a GE NX-148E-RF manual? We have 1 online manual for this item!
Question posted by juliebass05 on January 8th, 2020
Alarm Panel Beeping
My alarm panels keep beeping every 5-10 seconds. When I press *2, it says "control power trouble"
Current Answers
Answer #1: Posted by Odin on January 8th, 2020 6:10 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,730
Member since:
April 10th, 2010 Points: 41,236,730
See https://northeastsecuritysolutions.com/nx-8-security-system-troubleshooting/. If the issue persists or if you require further advice, you'll have to consult the manufacturer, for which use the contact information at https://www.contacthelp.com/general%20electric/customer-service.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related GE NX-148E-RF Manual Pages
User Manual - Page 2
... Emergency Activation keys that are programmed to work with your system. FIRE light is "on" to indicate fire alarm, flashes to indicate a trouble condition with your fire system. COMMERCIAL FIRE SYSTEM LCD KEYPAD
Model NX-148E-CF
READY light is "on" when the system is "on" when armed, "off" when disarmed, flashes to "force...
User Manual - Page 3
... Alarm Chime Forced Arming (s)
Group Bypass (s) Quick Arm (s) Re Exit Siren Test
(s) These features should not be enabled on UL listed systems.
NOTE: Some of the features described above may or may not be available for your user code. To Quick Arm and Exit: Press "Exit" key. Reset Smoke Detector and Panel Reset: Press 7
NX-148E...
User Manual - Page 5
...NX-148E-CF
3 TABLE OF CONTENTS
GLOSSARY OF TERMS 4 UNDERSTANDING THE LIGHTS 6 KEYPAD FUNCTIONS 7
Arming Your System In The "Away" Mode 7 Making Your System Ready To Arm 7 Arming Your System In The "Stay" Mode 8 Using The Quick Arm 9 Disarming Your System 9 Cancel / Abort Feature 10 Bypassing Zones 10... Alarm Memory 13 Test Function 13 Display Test Function 14 Light Control For X-10 ...
User Manual - Page 6
... should be turned on (ARMED) and off (DISARMED) by simply pressing the [STAY] or [EXIT] key. If your Security Control has been so programmed, you have of an alarm event. 5. YOU SHOULD BE AWARE OF THE FOLLOWING FACTS WHEN PREPARING A SAFETY/SECURITY PLAN FOR YOUR HOME/BUSINESS.
1. Your system will need to be able to easily...
User Manual - Page 7
...individual has when using an alarm panel.
Codes:
Can be "force armed" will not create an alarm.
A system that allows an instant alarm condition for ARMING only) as programmed by pressing either a four (4) ...code to be turned on the keypad control (for Entry/Exit doors, or grants a delay to allow someone to enter/exit the building without an alarm or before entering a user code to...
User Manual - Page 8
...pressing the [STAY] key when the system is armed.
6
NX-148E-CF Exit Light
The exit light is ready to arm and "flashes" if ready to prevent an alarm. Power Light
The power light is on if the primary power... [CANCEL] key during the last 10 seconds of a zone(s) being faulted.
The armed light will flash during or after an alarm report to disarm the system if ... trouble condition.
User Manual - Page 9
... keys • - The security system will flash rapidly for the last 10 seconds of the display to disarm and rearm the system if more time is off , you wish to bypass or unbypass one of these zones, press the [BYPASS] key while that the exit time is being displayed. Restore power if possible. Step 2
Enter...
User Manual - Page 10
... are secure. The stay light will be violated without an alarm.
NOTE: If any zone (s) have no longer have an entry
System Armed Instant
delay.
8
NX-148E-CF Restore power if ...power light is enabled, if you do not leave through a designated entry/exit door, the display will read "Instant", indicating that zone can be on or flashing. The steps to an "Instant" mode, press...
User Manual - Page 12
... during or after an alarm report to exit this light is now bypassed. Procedure #1 If you wish to bypass one or more zones, this must be bypassed. Step 3 The bypass light flashes. NOTE: The cancel feature must be enabled. Press the # key to ...the [CANCEL] key during an abort delay time. Entering a code followed by the [CANCEL] key while this viewing mode.
10
NX-148E-CF
User Manual - Page 14
... is pressed for two seconds. These keys should only be displayed. Check with those functions. The following list of the functions are not listed because they are programmed to be transmitted to that center.
If your security system will now begin scrolling though a list of the display.
NOTE: Some Panic/Hold-Up alarms are...
User Manual - Page 16
... "Off".
On the right side of the X-10 device you to the first language.
14
NX-148E-CF Step 6 Press # to "Select Light
Number 0 - 9". The LCD screen will again prompt you to exit from each keypad. Step 4 The LCD screen will prompt you to change languages. No alarms or reports will flash until complete. Step...
User Manual - Page 18
... beeping, the reset did not execute properly. Enter your installer.
16
NX-148E-CF Reserved Output 4 ?
If you wish to remove a partition, press the partition number on the LCD screen, press ...If the keypad still beeps after repeated attempts, please contact your code to silence the keypad. Arm / Disarm?
PROMPT Outputs used to reset Smoke Detectors, Zone Troubles, and Zone Tampers....
User Manual - Page 20
If the chime is turned on or off by pressing the [CHIME] key.
Step 4 Press the r key to move to select the proper hour. Step 2 Enter [master code]. SETTING THE SYSTEM CLOCK...FEATURE The door chime is on /off . The LCD Screen will be displayed with the current hour flashing.
Each press of week, date, month, and year.
If the chime is off, the chime light will be off and produce...
User Manual - Page 21
...a Fire Trouble condition. Press [#] to exit this entire manual to help you to its assigned partition 60 seconds after an alarm report, ...the NX-8 control panel. POWER will flash if the system has a low standby battery condition. It will illuminate if the primary power is ...will flash if ANY area is in the last 10 seconds of operation allows you understand the different screen messages ...
User Manual - Page 22
... on the bottom line
represent the areas that area is armed Instant. The following section.
20
NX-148E-CF
The numbers on the Armed line, that are disarmed and ready to be Force Armed. ... Armed
12345678 1234-678
This display is reflecting all of these areas, press the • up scroll key.
To control the individual areas, refer to arm
If ALL areas are armed. NOTE...
User Manual - Page 24
... and the AC power is disarmed.
and beeps 1 second at the end of your installer if a trouble condition exists.
22
NX-148E-CF
Beeps 3 times for the 'CHIME" feature. Beeps 1 second for trying to ... delay.
beeps rapidly for the last 10 seconds of the following conditions are detected: Zone or Box Tamper, Low Battery, AC Power Fail, or Expander trouble. KEYPAD CONTROL TONES (BEEPS)
A ...
User Manual - Page 25
... promptly if this display, press r 2 . Call your system is not operating properly.
To exit the service messages, press [#]-[#].
SERVICE DISPLAY
The following fault messages will be displayed. The standby battery is observed. A short circuit of time
Control Low Battery
Control Over-current
Control Phone trouble
Control Power trouble
Control Siren trouble
Expansion Aux.
User Manual - Page 26
... to the control.
A zone is not reporting to an expansion power supply is not on the bell or siren circuit. Press [r] to identify the zone.
24
NX-148E-CF
Press [r] to identify the zone. A short circuit of trouble on .
Expansion Box tamper
Expansion Low Battery
Expansion Over-current
Expansion Power trouble
Expansion Siren trouble
Expansion RF Jammed
Expansion Trouble
Zone Lost...
User Manual - Page 28
... without disarming the system.
Reports when the first partition is jammed
A smoke detector requires cleaning.
26
NX-148E-CF
A code has been entered. A zone "Walk-Test" mode has been activated.
DISPLAY Cancel
Cancel... Service End Code Entry First Open Last Close Sprnklr Clock Set RF Jammed CleanMe
Expansion Event Partial Arm Listen In Service Start Service End Code Entry First ...
User Manual - Page 32
NX-148E-CF USERS MANUAL NX148ECFUB03 REV B (MAY2003)
Similar Questions
Networx Nx-148e Manual Arm When Control Low Battery
(Posted by ramgw 9 years ago)
Where Can I Buy A Swing Down Door Replacement For A Ge Nx-148e Lcd Keypad?
I have owned the security system since 2007. It appears to not have changed by looking at the new on...
I have owned the security system since 2007. It appears to not have changed by looking at the new on...
(Posted by btestrake 9 years ago)
Ge Networx Nx 148e Security System
Just bought a foreclosed home & it has two security system panels, one on each level. I do not k...
Just bought a foreclosed home & it has two security system panels, one on each level. I do not k...
(Posted by Meadowsa 10 years ago)
My Security Fire Alarm Keeps Buzzing Which Is A Networx Nx-4 Model How Do I Stop
(Posted by Anonymous-32404 12 years ago)
Need The Address For The Nx 148e-rf To Program The Wireless Keyfobs.
(Posted by Anonymous-22456 13 years ago)