GE NX-1448E Support Question
GE NX-1448E Support Question
Find answers below for this question about GE NX-1448E - Security NetworX 48-Zone Fixed.Need a GE NX-1448E manual? We have 1 online manual for this item!
Question posted by bunch1951 on October 9th, 2011
Chirping Sound Coming From System
we hear a chirping sound every 30 seconds how can we find the source and correct it
Current Answers
Answer #1: Posted by antiroach on October 9th, 2011 4:44 PM
antiroach
Member since:
July 23rd, 2011 Points: 369,520
Member since:
July 23rd, 2011 Points: 369,520
Most likely, you have a low battery:
"Your alarm system has two power sources, a power transformer that is plugged into an electrical outlet and a backup battery that is located within the control panel box. If the battery is over five years old you will need to replace it. Open the box and you you will see the battery with a set of wires attached to it. Pull the wires off of the battery and take it to a local battery warehouse supply store. They will match it up with a new one. Plug the new battery into the system and your system should restore itself back to normal."
The above may, or may not, be the problem. I was able to find a User's Manual for your system. On page 25 of this pdf, you will find a number of reasons why your system is constantly chirping.
Nerds need love too...
Related GE NX-1448E Manual Pages
User's Manual - Page 2
... / EXIT DELAY TIMES
Exit Delay Time __________
Secondary Exit Delay Time ________
Entry Delay Time _________
Secondary Entry Delay Time _______
Page 2
NX1448E Icon Keypad
SECURITY SYSTEM NOTES
Installing/Service Company For Service Call Central Station
Duress Code
This system is
is not
partitioned.
User's Manual - Page 4
.... Understanding what the icons and sounds mean will obtain with two major factors:
1. Keep in the booklet. You should notify your system. Your security system is an electronic device and... single source of this booklet and, if possible, practice on site. The SECURITY CONTROL can be able to 60 icons and a built-in a weekly test of the security system. If your security system should...
User's Manual - Page 5
... testing. NX1448E Icon Keypad
Page 5 Care should be taken to plug in all situations.Use qualified security professionals to install and maintain your security control system. Smoke and heat detectors may be loud enough, wired correctly, and properly placed to provide notification of an alarm event.
Please read the following information and instructions...
User's Manual - Page 6
... INSTANT ICON 12 LISTEN-IN ICON 12 POWER ICON 12 READY / NOT READY ICON 12 SILENCED ICON 12 STAY LIGHT 12 TAMPER/TROUBLE ICONS 12 ZONE ICON 12 KEYPAD FUNCTIONS 13 ARMING YOUR SYSTEM IN THE "AWAY" MODE 13 ARMING YOUR SYSTEM IN THE "STAY" MODE 14 USING THE QUICK ARM...
User's Manual - Page 7
Optional 20 VIEW ALARM MEMORY 20 TEST FUNCTION - (Table of Contents continued...)
DISARMING THE SYSTEM 15 CANCEL / ABORT FEATURE 16 BYPASSING ZONES 16 GROUP BYPASS 16 UNBYPASSING 17 TURNING THE DOOR CHIME ON AND OFF 17 CHANGING USER CODES 17 ASSIGNING USER CODE AUTHORITY LEVELS 18 OTHER ...
User's Manual - Page 8
...the alarm system is either a four (4) or six (6) digit code that allows the user to bypass multiple zones with one or more zones open. An option that can program other user codes. An option that allows a special code to be ... Code Page 8
GLOSSARY OF TERMS
An option that allows the keypad to sound a ding-dong whenever an entry/exit door is sent during an alarm report. NX1448E Icon Keypad
User's Manual - Page 9
... that allows you to arm or disarm the system.
A four (4) or six (6) digit entry code used to turn on (ARM) the security system by pressing either the [STAY] or [EXIT] key on the keypad control (for ARMING only) as programmed by the installing company. Partitioned...2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47...
User's Manual - Page 10
.... NOTE: Some Panic/Hold-Up alarms are programmed to be transmitted to that center. If your security system will respond to the Panic/Hold-Up activation. This key can sound a local audible alarm when pressed for two seconds.
You should press these functions.
EMERGENCY ACTIVATION KEYS
NOTES: You must hold these keys for...
User's Manual - Page 11
... has been an alarm during the exit delay. "off" otherwise. Please note that a fire zone is in order to come on "; It will cause the cancel light to prevent an alarm.
Note: The cancel feature ... during the last 10 seconds of the exit delay as a warning that is flashing, all abortable reports will also be enabled.
EXIT LIGHT
The exit light is "on " when any zone in this light is ...
User's Manual - Page 13
... have no AC power.
NX1448E Icon Keypad
Page 13 Step 1
Close all protected zones and
sensors are secure.
Trouble conditions are: Tamper Hardware
Low Battery
Loss of Supervision
(A combination of Alarm... for a short period of this booklet for the last 10 seconds of the exit delay as a warning to the user that zone can be on or flashing when all protected doors and windows....
User's Manual - Page 14
... be bypassed if
you do not leave through a designated entry/exit door the instant icon will illuminate indicating that all interior zones are secure. If Auto Bypass is enabled, omit Step 3. • When "Auto Instant" is inside the premise and wants protection around the perimeter.
ARMING YOUR SYSTEM IN ...
User's Manual - Page 15
...Entry/Exit doors, the keypad control will sound a continuous tone for the duration of the entry delay, an alarm will allow the user to arm the security system in the AWAY mode by pressing the...or until you will turn on/off (toggle) all designated interior zones. (Optional) When armed, pressing the [EXIT] key will not disarm the security system. USING THE QUICK ARM (Optional, see page 1)
The ...
User's Manual - Page 16
... you wish to come on until the central station has received the cancel report.
press the [1] key for zone 1, press [1]-[2] for bypassing zones:
Step 1 Step 2 Step 3
Step 4 Step 5
Step 6...the [CANCEL] key during an abort delay time. The following steps are designated as group bypass zones will stop the communication process. Enter user code, if required (optional). Press the [BYPASS] ...
User's Manual - Page 17
NOTE: All zones will automatically be unbypassed each time the system is off, the chime light will be... will flash and zone icons will go off when unbypassed. UNBYPASSING To manually unbypass zones, perform the bypassing procedure on /off and produce a momentary ding-dong sound.
Each press of the [CHIME] key will toggle the chime feature on a zone that zone will illuminate specifying ...
User's Manual - Page 19
... instant icon is on , this code is programmed as a function code. This moves you want to give the user access or deny access. (Example: If zone icon #2 is lit, then the user is assigned access to partition #2. ICON 1 2 3 4 5 6 7 8
PARTITIONS ASSIGNED Partition 1 Partition 2 Partition 3 Partition 4 Partition 5 Partition 6 Partition 7 Partition 8
NX1448E Icon Keypad...
User's Manual - Page 20
...Step 2 Press a NUMBER key between 1 and 8 to exit the Assigning Authority Level Program. The zone(s) that created the last alarm will make the keypad sounder go to higher tones, pressing the [-] key...This returns you to its standard partition in ten seconds.
Step 4 If another user number to set this point you have been pressed for 60 seconds. Step 3 When the desired tone is now in...
User's Manual - Page 21
.../or a siren test. If the siren test is used to attempt another reset.
Enter your installer.
Optional
If programmed, this function will display steady those zones that were bypassed during the last alarm. Your system must be Disarmed to use the Reset function. Resets have now been performed. If the keypad...
User's Manual - Page 22
...
Step 5 Step 6
Enter the "Day Code".
Enter the last two digits of the "Year Code". SETTING THE SYSTEM CLOCK
Step 1 Press [r]-[9]-[7]. Enter Code icon will come on constant.
Note: The clock is a 24-hour clock. Must always be entered [0]-[7]. Step 2 Enter a ["Master Code"]. Then the ready icon will appear. Time 12...
User's Manual - Page 23
..., trouble and other service conditions. Press the [•] and [-] to set this adjustment in nature and will be on " if the security system requires service.
It is flashing, one or more zone icon(s) will be "on . SERVICE MENU
The service icon will be on ", press [r]-[2] to lighten or darken the illumination behind...
User's Manual - Page 25
... arm with the "Not Ready" icon off .
NX1448E Icon Keypad
Page 25
Beeps for 1 second or emits a "ding-dong" sound for any zone(s) are detected: Zone or Box Tamper, Low Battery, AC Power Fail, or Expander trouble. and beeps 1 second at the end of an exit delay;
Please contact your system will not change when...
Similar Questions
Entry Delay
How do I reset my system so the alarm goes off 60 seconds after entry instead of 30 seconds after en...
How do I reset my system so the alarm goes off 60 seconds after entry instead of 30 seconds after en...
(Posted by larrycarol195 11 months ago)
The Audible Countdown Warning Sometimes Occurs For No Apparent Reason
On two consecutive evenings the audible countdown warning came on without our having used any panel ...
On two consecutive evenings the audible countdown warning came on without our having used any panel ...
(Posted by flemingraf 1 year ago)
My 5812-rnd Is Chirping Every 30 Seconds
I removed the cover and there is no visible reset button. I only see a mother board and the red ligh...
I removed the cover and there is no visible reset button. I only see a mother board and the red ligh...
(Posted by skipsweat 4 years ago)
My Glass Break Sensor Continuously Chirps Every 30 Seconds. What Does This Mean?
My glass break sensor continuously chirps every 30 seconds. What does this mean?
My glass break sensor continuously chirps every 30 seconds. What does this mean?
(Posted by buddyt86525 7 years ago)
Change Security Code For: Ge Networx With Nx-1448e Keypad
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
(Posted by Jim39164 8 years ago)