GE IM4A Support Question
GE IM4A Support Question
Find answers below for this question about GE IM4A - G.E. Electronic Icemaker.Need a GE IM4A manual? We have 1 online manual for this item!
Question posted by sharihansen on March 14th, 2014
Icemaker Installation On Ge Pds22mbwabb
While installing the icemaker kit for a refrigerator that came with a condo we purchased, it called for a water valve shield with ground wire that should have come with the fridge. We don't have one so I tried to order. The shield is not available anymore, but I can get the ground wire. Is the shield absolutely necessary, or can we install without it. If we can install without it, where should the ground wire be connected? Thanks!
Current Answers
Related GE IM4A Manual Pages
Installation Instructions - Page 1
... are to be used to install an icemaker in the models listed below. To be used with your refrigerator. GBS20KBP GBS22HBP GBS22KBP PDS20MBP PDS20SBP PDS22MBP PDS22SBP
197D5736P001 49-60286-3 06-03 JR
Keep this addendum with an IM4, IM4A or IM6 Icemaker Kit. Installation Instructions Addendum
These instructions are needed to install an Icemaker Kit in your Owner's Manual and...
Installation Instructions - Page 2
... CAME WITH THE REFRIGERATOR
If the fill tube has been misplaced, call 1.800.626.2002 and order part WR02X11712. Fill Tube with Foil (5/8″ O.D.)
Water Valve Shield with Ground Wire
2
If the water valve shield has been misplaced, call 1.800.626.2002 and order part WR02X11753.
Installation Instructions
NEEDED CONTENTS OF KIT
The following are a list of the parts from the water valve...
Installation Instructions - Page 3
... the water tube inlet (10). Leave the power switch in place
Insulation plug
wall. Remove the label covering the hole. Installation Instructions
BEFORE YOU BEGIN
Read each step thoroughly before proceeding.
• CAUTION - Firmly press on some models) by lifting it to the refrigerator.
3 SET POWER SWITCH TO O (off)
Set the icemaker power switch...
Installation Instructions - Page 4
... this kit to record the date of the refrigerator). • The icemaker mounting screws are matched. Lock the plug in the hook on the back of the plug. Make sure the power cord is still firmly in the socket. • The fill tube extends into the fill cup opening (E). Continue to the Water Valve Assembly...
Installation Instructions - Page 5
... (8) from the kit into the
hole in the cabinet leg. Cut off excess tubing with ground wire completely onto the water valve.
2 CUT PLASTIC WATER TUBING
• Measure 25″ (64 cm) of water tubing starting from its electrical outlet.
3 ATTACH THE WATER VALVE
• Locate the female connector plug (C).
To eliminate the danger of the refrigerator, remove the screws...
Installation Instructions - Page 6
... the icemaker power switch to I (on the right side of the refrigerator.
• While still squeezing the clamp, insert the free end of the refrigerator about 1/2″ below the inlet. Installation Instructions
3 ATTACH THE WATER VALVE (cont.)
• Clip the end of the ground wire to the refrigerator cabinet.
6 ROUTE AND ATTACH THE WATER TUBE
• Fasten the plastic water tube...
Similar Questions
I Have A Wslp1500 Ge Washer. The Wash Is In, The Machine Filled, Then Quit. Lo
The wash is in, the washer filled, and then the machine stopped. In the display window Lo keeps popp...
The wash is in, the washer filled, and then the machine stopped. In the display window Lo keeps popp...
(Posted by goldenmountain27 10 months ago)
Im4a Just Installed,however There Is No Power Switch To Control On-off Functions
see above.
see above.
(Posted by skipteaches 8 years ago)
Im4a Icemaker
Trying to install a im4a ice maker on my he frig and my frig has the letter t on the back and the ma...
Trying to install a im4a ice maker on my he frig and my frig has the letter t on the back and the ma...
(Posted by BHUCK78 9 years ago)
Ge Profile, Pfss9pkyss, Wont Make Crushed Ice
(Posted by iyadbett 9 years ago)
Ge Refrigerator Gsh25jsxss Will Not Dispense Water
(Posted by fcerespa 9 years ago)