Garmin AIS 300 Support Question
Garmin AIS 300 Support Question
Find answers below for this question about Garmin AIS 300.Need a Garmin AIS 300 manual? We have 3 online manuals for this item!
Question posted by Anonymous-99241 on February 17th, 2013
Nmea 0183 Connection Between Garmin Ais300 And Garmin 700 Chart Plotter.
Could you please advise on the correct way to connect the NMEA 0183 data cable between my Garmin AIS300 and Garmin 700 series chartplotter. Thanks.
Current Answers
Related Garmin AIS 300 Manual Pages
Technical Reference for Garmin NMEA 2000 Products - Page 3
...™ 51 ◦ VHF 200/300 ◦ AIS 300 ◦ AIS 600
Note: PGN information is a checklist. by phone at 0808 2380000. Technical Reference for in the installation instructions provided with Garmin NMEA 2000-certified displays and sensors.
• The first section, NMEA 2000 Fundamentals, provides descriptions of the NMEA 2000 connectors and cables sold by phone at +44...
Technical Reference for Garmin NMEA 2000 Products - Page 4
... Sensor)...20 GHP 10 (Marine Autopilot System)...20 GXM 51...21 VHF 200...21 VHF 300...21 AIS 300...22 AIS 600...22
NMEA 2000-Certified Sensor Configuration Information...23 GPS 17x (GPS Antenna)...23 GFS 10 (Garmin Fuel Sensor)...24 GRA 10 (Garmin Rudder Angle Adapter)...26 GET 10 (Garmin Engine Tilt Adapter)...27 GFL 10 (Garmin Fluid Level Adapter)...29...
Technical Reference for Garmin NMEA 2000 Products - Page 5
... not have installed your boat. For a glossary of connected NMEA 2000 devices that are compatible with other NMEA 2000 micro connectors, cables, and NMEA 2000-compatible devices. Garmin NMEA 2000 Device Overview
Garmin uses NMEA 2000 micro connectors on your NMEA 2000 network, use the checklist on the product box shows which NMEA 2000 components are not included with a GFS 10...
Technical Reference for Garmin NMEA 2000 Products - Page 6
... can be used to protect against direct lightning strikes. NOTE: All male/female connections are NMEA 2000 approved. The following cables, connectors, and terminators are sold by Garmin, and as of a NMEA 2000 network are T-connectors, terminators, backbone/drop cables, and a power cable. Male* (not pictured)
010-11094-00
Field-installable connector - Female* (not pictured) 010...
Technical Reference for Garmin NMEA 2000 Products - Page 7
... power to which your NMEA 2000 network functions correctly.
others may require a separate power connection. Be sure to each device or sensor. Battery - 12 Vdc
Power cable Backbone extension cable
Drop cable
T-connector Male
terminator
NMEA 2000 backbone Sample NMEA 2000 Network
Note: This diagram illustrates the NMEA 2000 data connections to understand the following concepts...
Technical Reference for Garmin NMEA 2000 Products - Page 9
... a 24 Vdc power supply.
Be sure to connect the NMEA 2000 power cable to the top of the incorrectly designed NMEA 2000 network to correctly balance power on the network load and distance from the battery to the farthest device, in the documentation for Garmin NMEA 2000 Products
You can connect power to either at the end. The...
Technical Reference for Garmin NMEA 2000 Products - Page 12
...-Three-way connector with T-connectors, the backbone cables create the main communication path of the NMEA 2000 network. A T-connector is 100 m (328 ft.).
Drop Cable-Cable connecting a NMEA 2000 device to function correctly. Backbone Cable-In conjunction with one location. Device-Electronic hardware that indicates the amount of current a device draws from 9 to 16 Vdc, with Garmin NMEA...
Technical Reference for Garmin NMEA 2000 Products - Page 13
... Garmin Chartplotter and GPS Antenna Heading Sensor GPS Antenna
Technical Reference for a list of sensors may provide more about PGN information, see page 18. Refer to view or calculate that typically provides required PGN information. specific NMEA 2000 PGN information required to the following table for Garmin NMEA 2000 Products
Category Engine Information
Fuel Information
Data...
Technical Reference for Garmin NMEA 2000 Products - Page 14
... a Heading Sensor, and a GPS Antenna
• Wind Sensor and a GPS Antenna • Wind Sensor, a Water Speed
Sensor, and a Heading Sensor
(Continued)
10
Technical Reference for Garmin NMEA 2000 Products Wind Data, 127250 - Wind Data, 129026 - Envir Param
Humidity Sensor
130306 - COG/SOG and 129029 - Nav Data
Garmin Chartplotter and GPS Antenna
129026 - COG/SOG...
Technical Reference for Garmin NMEA 2000 Products - Page 15
... Data
Garmin Chartplotter and GPS Antenna
Maximum Apparent Wind Speed 130306 - GNSS Position])
Either a Wind Sensor, a Heading Sensor, and Speed Sensor or a Wind Sensor, a Heading Sensor, and a GPS Antenna
Opposite Tack Heading
130306 - GNSS Position])
Either a Wind Sensor and both Water Speed and Heading Sensors, or a Wind Sensor and a GPS Antenna
Technical Reference for Garmin NMEA 2000...
Technical Reference for Garmin NMEA 2000 Products - Page 16
... Speed Sensor, and Heading Sensor GPS Antenna, Water Speed Sensor, and Heading Sensor GPS Antenna GPS Antenna None None
12
Technical Reference for Garmin NMEA 2000 Products Temp, 130310 - Vessel Heading
129026 - Water Depth
130312 - Water Speed
129026 - Envir Param Old, or 130311 - General NMEA 2000 Data Type Requirements
Category Water
System
Data Type Depth Temperature
Speed Set...
Technical Reference for Garmin NMEA 2000 Products - Page 17
... 2000-Certified Display Device PGN Information
All data transmitted on every available Garmin NMEA 2000-certified display device, see the owner's manual for your display device. These groups are organized into groups.
Rapid Update
129029 GNSS Position Data
129038 AIS Class A Position Report
129039 AIS Class B Position Report
129040 AIS Class B Extended position report
129539 GNSS...
Technical Reference for Garmin NMEA 2000 Products - Page 32
... Select an option:
• For most Garmin chartplotters, select Review > Gauge Type. • For other Garmin marine devices, select Config > Engine Number. 3. From the NMEA 2000 Devices list, select the GET 10 device. 2.
The engine tilt is associated with the engine RPM, the adapter may be displayed on a connected Garmin chartplotter or marine instrument changes with . 4. Select the...
Technical Reference for Garmin NMEA 2000 Products - Page 42
... bare wire connected to power, and is the power balanced correctly on both ends of the NMEA 2000 network? (page 7) Are all drop cables less than 20 ft. (6 m)? (page 8)
For the latest free software updates (excluding map data) throughout the life of your NMEA 2000 installation. NMEA 2000 Checklist
Use this checklist to confirm your Garmin products, visit...
Installation Instructions - Page 1
...Connect the AIS 300 to install the Garmin® AIS 300 Automatic Identification System (AIS) Class B receiver device. Do not attempt to cause cancer, birth defects, or reproductive harm.
Ensure that is at least 15 3/4 in accordance with the packing list on the box. Select a location that the cables...Connect the AIS 300 to a VHF antenna and to a NMEA 0183-compatible chartplotter ...
Installation Instructions - Page 2
...AIS 300 power/data cable NMEA 2000 network power (not included)
NMEA 2000 network-page 4
AIS 300 Wiring Layout: AIS 300 Connected to a Garmin Chartplotter Through NMEA 2000
AIS 300 receiver box
RF cable to be installed alongside a VHF radio, but they can share the same VHF antenna if they are both installed on your boat.
AIS 300 Installation Instructions not
included)
NMEA 2000 drop cable...
Installation Instructions - Page 3
... model of Garmin chartplotter or to a non-garmin chartplotter, see page 5 for the NMEA 0183 Port 1 input on a GPSMAP 4000/5000 or GPSMAP 6000/7000 series chartplotter. not
included)
RF cable to a Garmin Chartplotter Through NMEA 0183
AIS 300 receiver box
VHF radio* (optional -
AIS 300 Wiring Layout: AIS 300 Connected to VHF antenna (not included)
AIS 300 power/data cable VHF radio...
Installation Instructions - Page 4
... NMEA 2000-compliant chartplotter using NMEA 0183, connect the yellow wire from the AIS 300 power/data cable to the Accessory On wire from the AIS 300 power/data cable to one on .
For more information. Connecting the Receiver Box to Power
Use the AIS 300 power/data cable to connect the receiver box to the installation instructions provided with the NMEA 2000 network.
Connect a marine...
Installation Instructions - Page 5
...Tx A (+)] from the AIS 300 power/data cable to the negative (-) battery terminal if you would like to limit the output speed to determine the correct NMEA 0183 baud rate. Connect the orange/white wire from the AIS 300, and leave the pink wire [Tx B (-)] wire unconnected.
• The AIS 300 can connect the AIS 300 to a Garmin chartplotter, ensure that you connected a power toggle switch using...
Installation Instructions - Page 6
... Class B Extended Position Report AIS Class A Static and Voyage Related Data AIS SAR Aircraft Position Report AIS Safety Related Broadcast Message AIS Class B "CS" Static Data Report, Part A AIS Class B "CS" Static Data Report, Part B
NMEA 0183 Communication Information When connected to http://my.garmin.com. by phone at +44 (0) 870.8501241.
AIS 300 Installation Instructions In the USA, go...
Similar Questions
How Do I Go Into Simulation Mode On A Garmin Marine Gps Modle741xs
how do I use simulation mode on a garmin 741xs marine ver
how do I use simulation mode on a garmin 741xs marine ver
(Posted by Curthupp 6 years ago)
541s Marine Gps. Depth Not Reading Out.
Depth has been working since installed. Now blank. Is there an on off control for this that may have...
Depth has been working since installed. Now blank. Is there an on off control for this that may have...
(Posted by therad50 11 years ago)
I Need Help Unlocking The Maps On My Garmin 5212 Chart Plotter
I need to know how to unlock the Maps on My Garmin 5212 chartplotter
I need to know how to unlock the Maps on My Garmin 5212 chartplotter
(Posted by chasman87 12 years ago)
Connection Between Ais 600 And Chart Plotter 750
How do i get my ais 600 to talk to my chart plotter 750? Instalation correct but soft ware seems at...
How do i get my ais 600 to talk to my chart plotter 750? Instalation correct but soft ware seems at...
(Posted by rlcady 12 years ago)