Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by godspianoplayer on January 29th, 2011
Frigidaire Im115 Problem With Water Freezing At Back Of Freezer.
Our ice maker acts like it "leaks" down the back of the ice maker and the interior of the freezer, which causes it to freeze a solid line of ice in the bin and back of freezer. My husband has checked to make sure that the unit is level in all directions. It is! It appears to me that it isn't level or the water wouldn't run down the back of the unit and the back of the freezer. We have to continuely break the ice and empty the bin and clean the back of freezer wall. How do we fix this problem? Thank you for your reply.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
... a kit from your dealer to order one. Water supply tubing made of the unit to a drinkable water source that is recommended for the water supply line.
ICE MAKER INSTALLATION INSTRUCTIONS
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from the softener may damage the ice maker, causing it greatly increases the potential for water leaks...
User Manual - Page 2
...Screws - Qty 2
6. Qty 2
10. Qty 1
11. Water Inlet Tube - Ice Maker
2. Leveling Bracket Screw - Qty 1
Tools Required:
• Putty Knife • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Plastic Clamp - Ice Container
3. Qty 1
7. Qty 1
9. Water Valve - Use This Page to Identify Parts
1. Qty...
User Manual - Page 3
....
5. DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser out away from back of refrigerator. Peel off label covering ice maker hole.
7. If refrigerator has exterior condenser (C), go to left condenser mounting bracket screw(s). Remove freezer shelf (some models).
3. If condenser is tight against back of inlet tube is mounted inside...
User Manual - Page 4
... bracket (7) to level ice maker (1). Make sure connection is same at top and bottom. Install adjustable leveling bracket (7) on back freezer panel. Start two, long, ice maker mounting screws (5) into water inlet tube (11) as far as it will be tightened later.)
13. Ice maker is level when gap between freezer wall and ice maker is tight.
10. Mount ice maker onto two screws (5) you...
User Manual - Page 5
... applying clamps.
17.
Use a power drill with exterior condenser, reinstall condenser brackets and tighten down screws.
21. Set ice container (2) on shelf.
18. Holes are only drilled through bracket and into bottom of water valve. Make sure connection is tight.
20. NOTE: Clean back of rear panel. On models with a Phillips® head bit...
User Manual - Page 6
... and flush supply line until water is used for supply line. • DO NOT install water supply tubing in new plumbing lines may cause ice to be moved out for the water supply line. DO NOT over tighten.
6. Air in areas where temperatures fall below freezing. • Connect the ice maker to a potable water source that leak.
9. Before Installing The Water Supply Line, You Will Need...
User Manual - Page 7
... to the closed position.
7 The ice maker turns off for short vacations. • If the ice maker will be sure the wire signal arm is in warm water with mild detergent.
Ice Maker Tips • Ice stored too long may develop an odd flavor. Rinse well and dry. • Stop the ice maker when cleaning the freezer or for a long period of...
Similar Questions
How Long Does It Take For Im115 To Ice Maker To Fill With Water
(Posted by susaarnd 10 years ago)
How To Install Im115 Frigidaire Icemaker
(Posted by abanerakiki 10 years ago)
Why Is There No Water Flow Once I Have Installed The Icemaker
(Posted by Anonymous-105808 11 years ago)
No Ice
Not making ice. Can hear the ice maker cycle... but doesnt make ice
Not making ice. Can hear the ice maker cycle... but doesnt make ice
(Posted by jfoster1500 12 years ago)
Frigidaire Im115 Problems
I installed an im115 ice maker. After all the connections were made, nothing happened. The valve nev...
I installed an im115 ice maker. After all the connections were made, nothing happened. The valve nev...
(Posted by bjs032960 13 years ago)