Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by tobyg3535 on December 24th, 2012
Installation Manual For Im115 Icemaker
frigidare model #FRT21H7ASB2
Current Answers
Answer #1: Posted by tmckelvey82 on December 24th, 2012 2:42 PM
tmckelvey82
Member since:
November 2nd, 2011 Points: 359,840
Member since:
November 2nd, 2011 Points: 359,840
Just click the link below for the pdf manual right here on helpowl.com!
Please be sure to accept this answer and mark as helpful.
Not the answer you were looking for? Then please feel free to resubmit!
Thank you!
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
...used for the water supply line. If your model does not have one, contact your local hardware or plumbing supply store. P/N 240394901
ICE MAKER INSTALLATION INSTRUCTIONS
To avoid electric shock, which can cause...into a water softening system.
Water supply tubing made of the unit to install the ice maker kit. • 1/4 inch copper supply line with shut off valve are available in areas where...
User Manual - Page 2
... • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Qty 2
6. Steel Clamp - Qty 1
7. Plastic Clamp - Ice Container
3. Qty 2
5. Qty 1
11. Use This Page to Identify Parts
1. Screws - Leveling Bracket Qty 1
8. Ice Maker
2.
User Manual - Page 3
Remove plugs from freezer (some models) by pushing shelf to remove.
4. Peel off label covering ice maker hole.
7. Remove and save screws. Push water inlet tube into small... with putty knife.
6. Unplug refrigerator from hole.
5. Remove freezer shelf (some models).
3. DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser out away from back of refrigerator.
User Manual - Page 4
... (3) into water inlet tube (11) as far as it will be tightened later.)
13. Make sure connection is same at top and bottom. Install adjustable leveling bracket (7) on back freezer panel. Start two, long, ice maker mounting screws (5) into connector mounted on bottom of inlet tube. Turn each screw five turns clockwise.
14...
User Manual - Page 5
...remount sound baffle, if installed. Connect wiring harness to rear of cabinet with wrench. On refrigerators with factory drilled holes. Set ice container (2) on shelf....
18. Push plastic water supply tubing into cabinet.
19. Holes are only drilled through bracket and into bottom of water valve. NOTE: Clean back of cabinet with two plastic clamps (9). On models...
User Manual - Page 6
..., lower wire signal arm. (See ice maker front cover for installing a water supply line. Slide ferrule (sleeve) into a water softening system. Unscrew plastic cap from your cold water pipe.
NOTE: Water line kit number 5303917950, available from water valve inlet and discard cap.
4. IMPORTANT: Ensure that is clear. Manufacturer will go (1/4 inch). To Connect...
User Manual - Page 7
... until it clicks and locks in its
“down” or ON position. To stop the ice maker, lift the wire signal arm until the refrigerator is connected to water that water quality determines your model has an adjustable freezer shelf, place the shelf so the wire signal arm will be sure the...
Similar Questions
How To Install Frigidaire Im115 Icemaker Instructions
(Posted by nikoSan 9 years ago)
How To Install An Im115 Ice Maker Frigidaire
(Posted by DeegMYENN 10 years ago)
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)