Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by soryanth on August 23rd, 2014
Ice Maker Model Number Gd-21.where Is The Filter Located And How To Replace It.
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
... brass compression nut and ferrule • Freezer shelf (Some models not eqipped with shut off valve are available in a kit from electrical power before connecting a water supply line to order... supply tubing in areas where temperatures fall below freezing. • Connect the ice maker to install the ice maker kit. • 1/4 inch copper supply line with shelf). To Avoid Property Damage: ...
User Manual - Page 2
... Required:
• Putty Knife • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Plastic Clamp - Ice Maker
2. Ice Container
3. Qty 1
7. Water Inlet Tube - Qty 2
10.
User Manual - Page 3
... water inlet tube into small hole on shelf to left condenser mounting bracket screw(s). Peel off label covering ice maker hole.
7. DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser out away from wall outlet.
2. Remove ice tray rack from freezer (some models) by pushing shelf to remove.
4. Remove and save screws.
User Manual - Page 4
... each screw five turns clockwise.
14. Make sure connection is same at top and bottom. Mount ice maker onto two screws (5) you installed in one half turn with screw (6). Ice maker is level when gap between freezer wall and ice maker is tight.
10. 9. Tighten screw (6) when level.
4 Push plastic water supply tubing (3) into freezer wall...
User Manual - Page 5
... NOTE: Clean back of rear panel. On models with a commercial household cleaner, ammonia or alcohol before applying clamps.
17. Locate factory punched holes at bottom right corner of cabinet...21. On refrigerators with a Phillips® head bit to water valve. 15. Use a power drill with dynamic condensers, remount sound baffle, if installed. Make sure connection is tight.
20. Set ice...
User Manual - Page 6
... and ferrule (sleeve) for the water supply line. NOTE: Water line kit number 5303917950, available from electric power supply.
2.
Place end of 1/4 inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) 1/4 inch brass compression nuts, (2) ferrules/sleeves, and instructions for the ice maker to the refrigerator. Push water supply line into sink or bucket.
User Manual - Page 7
... NOT place the ice container in your model has an adjustable freezer shelf, place the shelf so the wire signal arm will then produce more ice. • Occasionally shake the container to the closed position.
7 Ice Maker Tips • Ice stored too long may develop an odd flavor. The ice maker will hit the ice when the ice container is...
Similar Questions
How To Adjust Model Type Gd 21 Ice Maker
(Posted by 4s2gcmrharr 10 years ago)
Gd-21?
Does IM115 replace model GD-21? This is for the Frigidaire PLHT219SCK5. Thanks, Susan
Does IM115 replace model GD-21? This is for the Frigidaire PLHT219SCK5. Thanks, Susan
(Posted by honeyholmes 11 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)
Fridgidaire Ice Maker Model Gd-21. Drips Water Into Tray. No Cubes.
At work we have a Frigidaire refrigerator model GLRT212IDB1 with facory installed ice maker, model G...
At work we have a Frigidaire refrigerator model GLRT212IDB1 with facory installed ice maker, model G...
(Posted by hdmaster 13 years ago)