Frigidaire GLEQ2152ES Support Question
Frigidaire GLEQ2152ES Support Question
Find answers below for this question about Frigidaire GLEQ2152ES - Electric Dryer.Need a Frigidaire GLEQ2152ES manual? We have 4 online manuals for this item!
Question posted by HBChodian on March 6th, 2014
How To Replace Belt For Gleq2152es0 Frigidaire Electric Dryer
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by OnlineOutreachSpecialist on March 7th, 2014 8:14 AM
OnlineOutreachSpecialist
Member since:
March 30th, 2011 Points: 2,848,320
Member since:
March 30th, 2011 Points: 2,848,320
Hi HBChodian!
I understand you want assistance with replacing the belt on your Frigidaire dryer. I would certainly recommend a professional repair this for you considering the dryer belt is located in the bottom/rear of the appliance underneath the dryer house assembly. You would have to take the dryer almost half way apart to reach the dryer belt area. Then you must ensure the tension and installation are properly completed to avoid further damages. Please consider contacting a professional or your manufacturer to move forward. I hope this information is helpful to you.
Online Outreach Specialist
Related Frigidaire GLEQ2152ES Manual Pages
Use and Care Manual - Page 2
... This Use and Care Guide provides general operating
instructions for the recycling of electrical and electronic equipment.
These words mean:
DANGER You will help prevent potential negative... don't follow instructions. Use the dryer only as household waste.
Pedestal A pedestal accessory, Model No. Do not store or use any electrical switch; Installation and service must be...
Use and Care Manual - Page 3
..., serious bodily injury and/or damage to cooking oils in your dryer has a drying rack, always replace the lint screen when finished using this way ONLY
Power supply cord...laundry or throw rugs against the front or back of the dryer. • Do not spray any circumstances cut, remove or bypass the grounding prong from electrical power cord. SAVE THESE INSTRUCTIONS
3
Printed in the dryer...
Use and Care Manual - Page 4
...the risk of fire, electrical shock, or injury to persons, read and follow fabric care labels and laundry product labels. Items need room to the dryer: - Close the dryer door and select the cycle... until the dryer has stopped completely before reaching into the drum. • To prevent injury and damage to tumble freely for easy removal.
2. All repairs and servicing must replace the thermal ...
Use and Care Manual - Page 5
... do not let items hang over time. Remove the lint and replace the screen.
Do not operate the dryer without the lint screen in Important Safety Instructions and those listed below.
• Before cleaning the dryer interior, unplug the electrical power cord to the dryer.
Place the front bar under the lip of the lint...
Use and Care Manual - Page 6
... static electricity.
• Lint screen not clean
tumble without heat.
• Remove items when they are slightly damp
when cycle began.
• Use lint brush or roller to remove lint. This is normal with ammonia or any time. Care and Cleaning con't
Do not store or place laundry products on top of dryer...
Use and Care Manual - Page 7
... is not open . LP gas supply tank is connected to the dryer. Lint screen is overloaded.
Reset circuit breaker or replace fuse. Replace fuse. See INSTALLATION INSTRUCTIONS. High humidity.
Dryer is clogged with lint. Dryer runs but the heater will be clogged or restricted.
Electric dryer is empty or there has been a utility interruption of items.
See...
Technical Data Sheet - Page 1
... limit) thermostat has tripped too many trips in the digital display. Solution
Clear code, exit mode and start dryer. If problem persists, replace electronic control. If good, replace electronic control. If meter reads 240V on electric models and 120V on the relay RL2. If meter reads zero, remove power from control thermistor. If meter...
Technical Data Sheet - Page 2
... source is displayed.** 6 O'clock: Drive motor runs; d. Control thermistor reading is off .
Dryer will be reset for six seconds. 3. After entering the test mode, the program knob can ...press and hold Pause Cancel and START buttons simultaneously for six seconds or disconnect power from dryer. c. heat source is pressed, all LED'S will determine the value of the bottom three...
Installation Instructions - Page 2
... gasoline or other flammable vapors and liquid in the vicinity of this manual must be performed by a qualified installer, service agency or the gas supplier. ELECTRICAL REQUIREMENTS
ELECTRIC Dryer
CIRCUIT - Phillips head screwdriver. 2. POWER SUPPLY CORD - Duct tape. 6. branch circuit fused with upturned ends or closed loop connectors OR a 4-conductor power supply cord...
Installation Instructions - Page 3
...replace it must be expelled into a chimney, a wall, a ceiling, or any concealed space of water column, the system is too restrictive and the installation is acceptable: 1. The dryer exhaust system MUST be exhausted into the laundry area. If the dryer... building which has a swing-out damper(s) that open when the dryer is acceptable. EXHAUST SYSTEM REQUIREMENTS
Use only 4 inch (10.2 cm...
Installation Instructions - Page 4
... (1.27 cm) pipe.
3. However, on electric dryers, exhausting can be to the right side of the cabinet or the bottom of the dryer. Follow the instructions supplied with a solid door...)
13 1/2" (34 cm)
4 3/8" (11 cm) 3 3/4" (9.5 cm()9.5 cm)
GAS SUPPLY REQUIREMENTS
Replace copper connecting pipe that will cause an increase in vent restriction. The gas supply line should check the exhaust system...
Installation Instructions - Page 5
... proper operation in a recess or closet installation.
0" (0 cm)
0" (0 cm)
1" (2.54 cm)
0" (0 cm)
60 sq. cm)
CLOSET DOOR
0" (0 cm)
15" (38.1 cm)
1" (2.54 cm) 0" (0 cm)
5 This dryer MUST be exhausted outdoors.
5. MINIMUM INSTALLATION CLEARANCES -
inches (387.1 sq.
Installation Instructions - Page 6
... (70.49cm) 28.5 to clear door handle (72.39cm)
2.375" (6.03cm)
(34.29cm) 13.5" To rear & base exhausts
27.0"
(68.58cm)
Stacked Dryer Installation Dimensions
(68.58cm) 27.0"
Electrical supply on rear of unit
28.25" to front of cabinet(71.76cm)
28.75" to clear knobs (73.03cm) 29.5" to clear...
Installation Instructions - Page 7
...Remove one screw from your dealer.
5. REMOVE 4 SCREWS (ONE FROM EACH HINGE FIRST)
7 If dryer is exhausted through the floor and area beneath the mobile home is not applicable, with no obstructions....when such standard is enclosed, the exhaust system MUST terminate outside make up or move the dryer.
2. Hold the door firmly before removing the last two screws.
3. Rigid metal duct is...
Installation Instructions - Page 8
... the four screws that secure the door hinges to avoid scratching the paint. 5. Remove the two handle hole plugs from turning. Be careful to the dryer front panel. Install the plugs from Step 3 into the holes left by removing the handle screws in Step 4. 9. Be careful to reinstall the hinges. 11...
Installation Instructions - Page 9
... having an equipment-grounding conductor and a grounding plug, the plug MUST be plugged into a properly grounded three-prong receptacle. GROUNDING REQUIREMENTS
ELECTRIC Dryer
Improper connection of the cord, resulting in electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is a copper wired power cord with the...
Installation Instructions - Page 10
...screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer with the green ground screw.
6. Finger tighten the nut only at this time.
Reinstall the terminal ...STRAIN RELIEF MOUNTING B R A C K E T POWER CORD
POWER CORD
ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM
ELECTRIC Dryer
ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM...
Installation Instructions - Page 11
...-9044, or visit our website, www.frigidaire.com, for service.
7. NOTE: On gas dryers, before the burner will shut the burner off at circuit breaker/fuse box before making another attempt to children.
NOTE: A wiring diagram is resting solid on a soapy water solution. REPLACEMENT PARTS
If replacements parts are not meant to the corrosive...
Operating Instructions - Page 1
... the end of the cycle and periodically during unloading. To select an option, press OPTIONS until the desired selection is selected. The dryer senses the moisture level of fire, electric shock or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS in detail.
1.
To reduce the risk of the load as it tumbles...
Operating Instructions - Page 2
... wrinkle free, permanent press and lightweight fabrics. or to dry items containing feathers, down , foam rubber, plastic, or similarly textured, rubber-like materials;
See the "Dryer Settings Chart" for the desired option flashes, then press SELECT.
For loads requiring less drying time, select Less Dry. If an option is recommended for...
Similar Questions
Replaced Control Board Frigidaire Dryer Model Feq1442ceso,still Flashing,beeping
(Posted by stlhdr 9 years ago)
How To Replace Heating Element In Dryer Model Aeq7000eg0
(Posted by 19mcbriv 9 years ago)
Give Me A Diagran Of Where Is The Fuse Locatedin A Frigidaire Electric Dryer
(Posted by 101robi 9 years ago)
How To Replace Frigidaire Gleq2152es0 Dryer Belt
(Posted by lovelDainj 10 years ago)
Heating Element For Gleq2152es0 Frigidaire Dryer How To Repair
(Posted by rajibKimb 10 years ago)