Frigidaire FER641FS Support Question
Frigidaire FER641FS Support Question
Find answers below for this question about Frigidaire FER641FS - 27" Electric Dryer.Need a Frigidaire FER641FS manual? We have 2 online manuals for this item!
Question posted by steffwendt on October 7th, 2012
Hi, Our Dryer Wont Get Hot Anymore. Also Noticed A Burned Smell When It Started.
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by Anonymous-74890 on October 10th, 2012 9:37 AM
Anonymous-74890
Member since:
September 17th, 2012 Points: 73,690
Member since:
September 17th, 2012 Points: 73,690
Hello – When was the last time the ducting in your home was cleaned and confirmed that it has no debris or build up? Turn the breaker to the unit off for 5-6 minutes. Turn the unit’s power back on and try a cycle again. If this does not prove to be successful here are a few possible causes that a technician would be required to check: defective heating element, control board, power supply (240v), high limit thermostat or defective sensor.
Related Frigidaire FER641FS Manual Pages
Owners Guide - Page 1
... proper operation and care.
Read and Save These Instructions
Record Your Model and Serial Numbers
Record below the model and serial numbers found on the dryer serial plate located on the left side of Contents
Important Safety Instructions 2 Drying Procedures 3 Features 3 Common Drying Problems 4 Care and Cleaning 4 Avoid Service Checklist 5 Warranty...
Owners Guide - Page 2
... this
To prevent injury, do not reach into a properly grounded and polarized 3-prong outlet. Clean the lint screen before using this plug. Fire hazard,
ELECTRIC DRYER
overheating and damage to a gas pipe. Do not stack or place laundry or throw rugs against the front or back of ventilating air. Items contaminated with your...
Owners Guide - Page 3
...Start Button for 2 seconds or turn pockets inside out. • Be sure buckles, buttons and trim are dry, remove the rack and replace the lint screen. If load is ON, a signal will fill the drum 1/3 to ON, hold for directions on top of static electricity..., read and follow fabric care labels and laundry product labels. Close the dryer door and set some models) Use the drying...
Owners Guide - Page 4
... before starting the dryer.
The...dryer cabinet interior and exhaust duct.
Hang or fold.
4
• Do not overload dryer. • Remove items as soon as cycle ends. Do not store or place laundry...electrical shock could result in Important Safety Instructions and those listed below.
• Before cleaning the dryer interior, unplug the electrical power cord to avoid electrical...
Owners Guide - Page 5
...pockets before starting each cycle.
Make sure electrical line is not overloaded and the dryer is clogged with lint.
LP gas supply tank is restored. Dryer should ...dryer. Excessive wrinkling.
Scratching or chipping of the dryer feels too hot or smells hot. Remove objects from the dryer lint screen before laundering. It may be hitting the inside the dryer.
Check to the dryer...
Owners Guide - Page 6
... calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other appropriate payment record to change without notice. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
Electrolux authorizes no person to establish the warranty period should service be required. Obligations for service calls...
Installation Instructions - Page 2
...
2
Exhaust System Requirements
2-3
Gas Supply Requirements
3
Location of "four Dryer
4
Mobile Home Installation
5
Roughdn Dimensions
5-6
Unpacking
6
Reversing Door Swing
6
Electrical Insta%8on
7
Grounding Requirements
7
Electrical Connections--3-wire
7
Electrical Connections--4-wire
8
Installation
8
Replacement Parts
8
PREdNSTALLATION
REQUIREMENTS
Tools and Materials...
Installation Instructions - Page 3
... the current CAN/CGA B149
2 The gas supply line should be of 1/2 inch (1 27 cm) pipe
3 If codes allow, flexible metal tubing may cause condensation and faster accumulation ... of the dryer, On gas dryers, exhausting can be accomplished by installing Exhaust Kit, P/N 131456800, available through
system to down ) and start the dryer
3, Read the measurement on electric dryers, exhausting can...
Installation Instructions - Page 4
.... 3 On carpet Floor MUST be solid with a maximum slope of 1 inch (254 cm)
INSTALLATION tN RECESS OR CLOSET 1 A dryer installed in a bedroom, bathroom, recess or closet, MUST
be exhausted outdoors_ 2 No other fuel burning appliance shall be unobstructed when a door is installed_ A Iouvered door with equivalent air openings for the full length...
Installation Instructions - Page 5
...dryer exhaust outlet.
4. MOBILE HOME INSTALLATION
1. Mobile Home Installation Kit No. 169840 is applicable. GAS PIPE
t" (2.54 cm)
REAR VIEW
Correct Correct
Incorrect
L
DoN
©
Incorrect
L
47 1/2" (120.7 cm)
DOOR OPEN 90 °
4 3/8"
L
(11.1 cm) _
OPTIONAL
VENT KNOCKOUT_-_
Correct
L
L
Incorrect
27..., with no obstructions.
Dryer MUSTbe exhausted outside the ...
Installation Instructions - Page 6
....7era}
3_ H
(91.5 cm)
;3 3/4_ (9.5 ¢m}
318" {0ogg ¢m} DIA° GAS PiPE
REAR ViEW
B
4.3/8"
(11.1 cm}
OPTIONAL VENT KNOCKOIJT. _
_"
27'
(68°6 cm}
SIDE ViEW
REVERSING DOOR SWING
Your dryer is designed so the door swing may be reversed at any time without additional parts, Conversion is accomplished by transferring hinges...
Installation Instructions - Page 7
... codes and ordinances If in doubt, call a licensed electrician
1
"4LLGASDGvers
1
1 The laundry center is equipped with this dryer. ELECTRfCAL INSTALLATION
ALL ELECTRIC Dryers
The following are specific requirements for proper
and safe electrical installation of your dryer Failure to follow these instructions can create electrical shock and/or a fire hazard.
_liance
MUST be_perly grounded...
Installation Instructions - Page 8
... corner,
2.
If the burner does not light within 45 seconds the first time the dryer is turned on the terminal block, Tighten the screw securely.
7. ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM
Non -Canadian ELECTRIC Dryer
1
1 Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on top of the...
Similar Questions
Dryer Wont Stay Heated
dryer heats up and then you hear a click in the contro panel and the the dryer stops heating but is ...
dryer heats up and then you hear a click in the contro panel and the the dryer stops heating but is ...
(Posted by debbieloubert 9 years ago)
Help My Dryer Wont Start
I dont know what exactly happened but from one day to the next my dryer just wont start. It displays...
I dont know what exactly happened but from one day to the next my dryer just wont start. It displays...
(Posted by stephaniesgarzaamca 9 years ago)
What Size Are The Screws For The Dryer Whip?
What size are the screws for the dryer whip?
What size are the screws for the dryer whip?
(Posted by Anonymous-141832 9 years ago)
Frigidaire Electric Dryer Fer641fs. No Heat. Timer Not Advancing.
My electric dryer has no heat and the timer is not advancing like it suppose to. It just keeps spinn...
My electric dryer has no heat and the timer is not advancing like it suppose to. It just keeps spinn...
(Posted by mouatech 10 years ago)
Dryer Heating Element
Dryer heating element gets to hot and stays on even when the dryer is shut off.Gets hot enough that ...
Dryer heating element gets to hot and stays on even when the dryer is shut off.Gets hot enough that ...
(Posted by slong1022 10 years ago)