Frigidaire ATF8000FS Support Question
Frigidaire ATF8000FS Support Question
Find answers below for this question about Frigidaire ATF8000FS - Gallery - Washer.Need a Frigidaire ATF8000FS manual? We have 5 online manuals for this item!
Question posted by IFFY09 on October 25th, 2011
Fafs4473l0 Err.code E9f What Is This
WASH FRIGIDAIRE HAVE ERRO CODE E9F MB-FCV COMM WHAT DOES THIS MEAN
Current Answers
Answer #1: Posted by OnlineOutreachSpecialist on October 26th, 2011 12:57 PM
OnlineOutreachSpecialist
Member since:
March 30th, 2011 Points: 2,848,320
Member since:
March 30th, 2011 Points: 2,848,320
This is a communication protocol error. Typically technicians check the following:
Communication problem. Check the wiring between the Main Control Board and the Speed Control Board. Wiring bad, correct wiring problem. Wiring good, replace the Main Control Board. If the problem is not corrected, replace the Speed Control Board.
You can see this is not a typical DIY type of job. Please contact your manufacturer or a service provider.
Online Outreach Specialist
Related Frigidaire ATF8000FS Manual Pages
Use and Care Guide - Page 2
... you purchased the product. Table of Contents
IMPORTANT SAFETY INSTRUCTIONS ...3-4 Washing Procedures ...4-6 Stain Removal ...6-7 Common Washing Problems ...8 Care and Cleaning ...9 Avoid Service Checklist ...10 Warranty...11... by the manufacturer could otherwise be used when elevating the washer for your appliance. These words mean:
DANGER You can happen if the instructions are found on...
Use and Care Guide - Page 3
... to 30 minutes, if the washer has not been manually turned off vapors that could result in , or spotted with local codes. Prevent Fire • Do not wash items that has not been used... it becomes overheated. Incorrect usage can become airtight chambers. • Keep laundry products out of the washer must never be exposed to the OFF position does not disconnect this
Owner's Guide...
Use and Care Guide - Page 4
... heavy soil. Do not use an adaptor plug or extension cord or remove grounding prong from this washer.
1. Common sense and caution must be washed together.
Add laundry load to washer.
4
Add laundry load to washer. • Combine large and small items in the wash load. • Mend rips and tears to prevent further damage during the...
Use and Care Guide - Page 5
...dispenser drawer. • After adding laundry products, slowly close the dispenser ...fabric softener to the detergent compartment.
Look for this symbol on the wash load. • Use of the siphoning action and is added. &#...detergentbooster and enzyme products may see water in early dispensing of the washer. D.
Fabric damage can be added to automatic dispenser following these ...
Use and Care Guide - Page 6
...cycle is on top of washer at any utensil used. • Do not combine stain removal products, especially ammonia and chlorine
bleach. Do not store or place laundry products on contact with ...fire or serious injury to hang on an inside the washer. These mixtures can produce dangerous fumes which have been previously cleaned in, washed in, soaked
in the
stain removal chart below :
&#...
Use and Care Guide - Page 8
...;Add liquid fabric softener to reduce abrasion.
• Rewash load.
•Increase water temperature using full permanent press cycle.
Wrinkling
•Overloading the washer. •Incorrect wash cycle for wash
load.
•Reduce load size. •Rinse in dryer. •Remove lint with liquid fabric
softener using hot or
warm water. Stiff, harsh...
Use and Care Guide - Page 9
... parts of warm water and mild detergent. Inside • Remove items from hoses. 3. Clean these winterizing instructions to prevent damage to empty wash
drum. Press START and let the washer drain for 1 minute
to future loads. Remove dispenser drawer. Drain any of the cleaning items mentioned for cold weather care. Replace drawer...
Use and Care Guide - Page 10
...8226; Motor is restarted, objects may not be at faucet or washer. Stop washer and rearrange wash load. Turn on floor. Wash load too wet after a cool down period of the siphoning action...Standpipe must be enough hot water available for service, review this washer. See INSTALLATION INSTRUCTIONS.
10 Washer won't spin. See Washing Procedures. • Load is filling. • Water inlet ...
Operating Instructions - Page 1
...extended by an internal boost heater to 90 minutes. Start the washer. • Close the door and press Start/Pause. Add laundry load to select the cycle. "PAU" will be set at... the end of the cycle
is selected in either direction to the wash drum.
5. Remove items from the washer when the cycle ends. Sort laundry...
Operating Instructions - Page 2
...F
Auto Temp Cold 65° F
Cold
Temperature of wash load. The washer automatically adjusts the water level to the cycle will be ...the wash portion of any button during operation of the cycle will produce flashing indicator lights, beeping and "Err" will...by 2 rinses and a slow final spin. To protect your laundry items, not every option is displayed alternately with every cycle....
Parts Catalog - Page 5
...134364900 134550600 131800405 134372000 134601625 131843146
DESCRIPTION Hose, water inlet, 4 ft., hose & washer Screw, pan head, 8-18B x 0.31 Control Board, motor Wiring Harness, motor...panel, reinforcement Bracket, RS panel, reinforcement Retainer, spring steel Panel, work top, black Screw, hex washer head, M5 0.8 x 15 Bracket, hinge, reinforcement Panel, service access, rear Panel, cabinet front,...
Parts Catalog - Page 7
...Publication No: 5995498952
# Functional Parts
7
* Non-Illustrated Parts
09/07 Bracket, shock mtg. Screw, washer hd, 10-16AB X 0.75 Cable Tie, 5.60 inch Pump, drain Filter, pump Hose, coin trap... bellows clamp, retainer Bellows Kit, boot, w/light hole Nut, hex, 1/4-20 UNC-2B, (2) Washer, Bellville, spring steel Plate, counterweight Shell, tub, front Spring Assy, suspension Screw, hex head, ...
Installation Instructions - Page 1
...DO IF YOU SMELL GAS · Do not try to the washer must conform with local codes and ordinances and the latest edition of this manual must be ...Installation Requirements Electrical Requirements Grounding Requirements Water Supply Requirements Drain Requirements Rough-In Dimensions Location Of Your Washer Unpacking Installation Replacement Parts
PAGE
2 2 2 2 2 3 4 4-5 5-6 6
Installation and...
Installation Instructions - Page 2
... Electrical Codes, ANSI/NFPA 70 (latest edition). The standpipe height above the floor should be: Minimum height: 24 in. (61 cm) Maximum height: 96 in. (244 cm)
accessible when the washer is..., available from an authorized parts distributor.
2 ELECTRICAL REQUIREMENTS
CIRCUIT - NOTE: Because of this washer with 15 amp. DO NOT cut off or alter the grounding prong on the power supply cord...
Installation Instructions - Page 4
... Remove the carton.
2. Base
Shipping Plug In an area exposed to protect the floor, lay the washer on it will come in . On carpet. per foot (1.27 cm per 30.5 cm). Cut... with a maximum slope of the floor may be below 60 ° F
(15.6 ° C) for proper washer (detergent breakdown) operation.
2. Remove and save the styrofoam base and shipping plug. The ambient temperature should never be ...
Installation Instructions - Page 5
... install them in the holes vacated by the packaging spacers. Adjust the appropriate leg so the washer is SOLID on the floor on alternate corners and sides and feel for leaks. Run some ...water from the plastic bag located in the drum of the washer and install the rubber washers in it's
final position, place a level on and check for the slightest movement. Tighten ...
Installation Instructions - Page 6
..., property damage or damage to the standpipe, inlet hose, laundry tub, etc. Cable Tie
REPLACEMENT PARTS If replacements parts are understood and practiced as a routine with your washer, call 1-800-944-9044, or visit our website, www.frigidaire.com, for ease of the washer. Children might use accessories certified by the manufacturer could result...
Data Sheet - Page 1
...- The code will signal the last error code.
Diagnostic Test The diagnostic test is this occurs.
134879700A (0702) "Err" -
Pressing...washer to confirm functionality. 2. If this happens, the motor control has power.
2. Check the 5 pin connector wiring between the console control and the motor control. The bleach and the wash water solenoids will signal the last error code...
Data Sheet - Page 2
... board problem. Refer to test (2). Hot and cold water hoses switched. E44 Control board problem. E71 Wash NTC failure. (Tub heater) E74 Wash temperature does not increase. Refer to test (5). If above 130 VAC. Error code
Error code chart
Fault condition
E11 Fill time too long. E43 Control board problem. Replace the control board...
Data Sheet - Page 3
...there an air leak in ?
4. Better models, replace the pressure sensor.
5.
Does water enter the washer continuously.
3.
Go to step (4). Turn water faucets on. No. No. Replace the inlet valve assembly....board. No. Go to step (6) Yes. Yes. Go to step (3).
Go to enter the washer?
5. Correct problem. Replace the control board. 120 VAC. If this correct the problem? If wiring...
Similar Questions
Frigidaire Gallery Washer Won't Spin With Load In It Gltf2940fs2
(Posted by brentgowtha 9 years ago)
Frigidaire Affinity Front Load Washer Atf8000fs1 Does Not Start
(Posted by puzahhs 9 years ago)
How To Get Out Of Diagnostic Mode On Affinity Washer
(Posted by jolbs 10 years ago)
Washer And Dryer Go Down The Same Day
dryer drum will not move, stopped working all togather, washer won't spin all the water out. atf8000...
dryer drum will not move, stopped working all togather, washer won't spin all the water out. atf8000...
(Posted by jimmycookjc21 11 years ago)