Fluke 179 Support Question
Fluke 179 Support Question
Find answers below for this question about Fluke 179.Need a Fluke 179 manual? We have 10 online manuals for this item!
Current Answers
Related Fluke 179 Manual Pages
Fluke 73, 77, 175, 177, and 179 Digital Multimeter Datasheet - Page 1
...; Electronics 179 Multimeter and
Deluxe Accessory Combo Kit
• 179 and IR Thermometer Combo Kit
Feature Max voltage True-rms Temperature Basic dc accuracy Backlight Min/Max/Avg ToolPak meter hanging kit with magnet
73 600
0.3 %
77 1000
0.3 %
175 1000
177 1000
179 179/TPK
1000
1000
0.15 % 0.09 % 0.09 % 0.09 %
Opt
Opt
Opt Included
Fluke 73...
Fluke Current Clamp Meters - You Can Guess Which Fuse is Bad or You Can Try This Application Note - Page 1
... Note
You've got a bad fuse in min/max mode with an open phase. That's because a three-phase induction...troubleshooting is
sometimes done on each phase: the phase with a clamp accessory. good indications of why the fuse opened. A damaged enclosure or ...circuit power is drawn from , how do you can try this method is particularly useful. From the Fluke Digital Library @ www.fluke.com...
Fluke Digital Multimeters - 10 Dumb Things Smart People Do When Testing Electricity Application Note - Page 2
.... • Appliance outlets with short connections to utility power.
• Electricity meters, primary overcurrent protection equipment. • ...Fluke Corporation PO Box 9090, Everett, WA USA 98206
Fluke Europe B.V. All rights reserved.
i.e., where low-voltage
connection is made to service
entrance. IEC 1010 applies to well pump. CAT I
Electronic
• Protected electronic...
Fluke Multimeters - ABCs of Multimeter Safety Multimeter Safety and You Application Note - Page 2
... circuits, they tend to low-voltage (< 1000 V) test equipment.
Fluke Corporation ABCs of a power distribution system into categories is based on the fact that a dangerous high-energy... as CAT I
Electronic
• Protected electronic equipment. • Equipment connected to (source) circuits in larger buildings. • Appliance outlets with higher power available and higher-energy...
Fluke Multimeters - ABCs of Multimeter Safety Multimeter Safety and You Application Note - Page 3
... CAT I electronic circuitry, whatever...built-in CAT I location could actually encounter dc voltages much higher than the power line ac voltages measured by the European Commission and mandated through your hand,...
Independent testing
Independent testing is not, therefore, a guarantee of multimeter safety Fluke Corporation
ABCs of independent testing. Why? UL 3111, for the presence...
Fluke Multimeters - ABCs of Multimeter Safety Multimeter Safety and You Application Note - Page 6
... Hook on the side of safety.
Fluke Corporation ABCs of multimeter safety
Use protective equipment such as programmable controllers, it is common to find electronic circuits (CAT I . Second, test the ... proper lock-out/tagout procedures. remove
watches or other hand, is CAT I ) and power circuits (CAT III) existing in close proximity. Wear flame resistant clothing,
not ordinary work ...
Fluke Multimeters - Anatomy of a High Quality Meter Application Note - Page 2
... 2140271 A-ENG-N Rev A
2 Fluke Corporation Anatomy of valuable safety information and...whenever possible. typically covers electronic equipment
• Protected electronic equipment • Equipment ...accessories. And a system is a meter flashing, "low battery." But a failing battery is not what you and a powerful electrical circuit is only as good as its accessories as the accessories...
FE 175,177,179 Users Manual - Page 1
Printed in USA. All rights reserved. ®
Models 175, 177, 179
True RMS Multimeters
Users Manual
May 2003 (English) © 2003 Fluke Corporation.
FE 175,177,179 Users Manual - Page 3
...Contents
Title
Page
Contacting Fluke ...1 "Warning" and "Caution" Statements 1 Unsafe Voltage...1 Test Lead Alert ...1 Battery Saver ("Sleep Mode 2 Terminals ...2 Rotary Switch Positions...2 Display ...3 MIN MAX AVG Recording Mode 4 Display HOLD and AutoHOLD Modes 4 YELLOW Button ...4 Display Backlight (Model 177 and 179 Only 4 Manual Ranging and Autoranging 5 Power-Up Options ...5 Making...
FE 175,177,179 Users Manual - Page 5
... or tests the following:
♦ AC / DC voltage & current
♦ Diodes
♦ Resistance
♦ Continuity
♦ Voltage & current frequency ♦ Temperature (Model 179 only)
♦ Capacitance
Contacting Fluke
To contact Fluke, call: 1-888-993-5853 in USA 1-800-363-5853 in Canada +31 402-678-200 in Europe +81-3-3434-0181 in Japan...
FE 175,177,179 Users Manual - Page 6
... Positions
Switch Position
Measurement Function
K
AC voltage from 3.00 mA to 1000 V.
The Sleep mode is no function change or button press for 20 minutes.
Common (return) terminal for 2...overload for 30
BA seconds maximum). Models 175, 177 & 179 Users Manual
Battery Saver ("Sleep Mode")
The Meter enters the "Sleep mode" and blanks the display if there is always disabled in the MIN...
FE 175,177,179 Users Manual - Page 8
...Backlight (Model 177 and 179 Only)
Press to activate MIN MAX AVG mode. Models 175, 177 & 179 Users Manual
MIN MAX AVG Recording Mode
The MIN MAX AVG recording mode captures the minimum and ....
⇒ ⇒
h h Press MIN MAX to select DC mA, DC A, Hz, temperature (Model 179 only), capacitance, diode test. The backlight automatically turns off .
⇒ To exit and erase stored readings,...
FE 175,177,179 Users Manual - Page 9
...minute backlight timeout.
(Model 177 and 179 Only)
5 Manual Ranging and Autoranging
The Meter has both Manual range and Autorange modes.
⇒ In the Autorange mode, the Meter selects the range with...YELLOW)
Disables automatic power-down the button indicated while turning the Meter from OFF to Autorange and Auto Range is in a MIN MAX AVG Recording mode, or the AutoHOLD mode.
When you turn...
FE 175,177,179 Users Manual - Page 10
Warning
To avoid electric shock, injury, or damage to the Meter, disconnect circuit power and discharge all high-voltage capacitors before
XW removing the common test lead.
when removing the test leads, remove the live lead; Models 175, 177 & 179 Users Manual
Making Basic Measurements
The figures on the following pages show how...
FE 175,177,179 Users Manual - Page 11
... Continuity
HOLD MINMAX RANGE
HOLD MINMAX RANGE
Testing Diodes Good Diode
HOLD MINMAX RANGE
Making Basic Measurements
Good Diode
HOLD MINMAX RANGE
Measuring Temperature (Model 179 Only)
AIK06F.EPS
HOLD MINMAX RANGE
RANGE
Vent
80BK1 Type K Thermocouple
or Pipe
Probe
XWWarning: Do not connect 80BK1 to live circuits. AIK10F.EPS
+
_
Single...
FE 175,177,179 Users Manual - Page 12
... accurately measure distorted waveforms. Calculating True RMS converters require a certain level of range. Turn power OFF, break circuit, insert Meter in -circuit current measure- They do not affect the specified...AC
HOLD MINMAX RANGE
DC mA
+ +
A
CAT CAT
AIK08F.EPS
8
Models 175, 177 & 179 Users Manual
XW Measuring AC or DC Current Warning
To avoid personal injury or damage to the Meter:...
FE 175,177,179 Users Manual - Page 14
XW Testing the Fuses
Warning
To avoid electrical shock or injury, remove the test leads and any input signals before replacing the fuse.
Do not use abrasives or solvents.
Models 175, 177 & 179 Users Manual
Cleaning
Wipe the case with a damp cloth and mild detergent.
HOLD MINMAX RANGE
440 mA
11 A Test fuses as shown below. Dirt or moisture in the terminals can affect readings.
FE 175,177,179 Users Manual - Page 16
... to 1 kHz)
60.00 mA 400.0 mA 6.000 A 10.00 A
0.01 mA 0.1 mA 0.001 A 0.01 A
1.5 % + 3
1. Models 175, 177 & 179 Users Manual
Function
Range 1
Resolution
Accuracy ± ( [ % of Reading ] + [ Counts ] )
Model 175
Model 177
Model 179
AC Volts 2,3
600.0 mV 6.000 V 60.00 V 600.0 V 1000 V
0.1 mV 0.001 V 0.01 V 0.1 V 1 V
1.0 % + 3 (45 Hz to 500 Hz...
FE 175,177,179 Users Manual - Page 17
... input burden voltage (typical): 400 mA input 2 mV/A, 10 A input 37 mV/A. 5. Frequency is the specified accuracy of Reading ] + [ Counts ] )
Model 175
Model 177
Model 179
DC Amps4
60.00 mA 400.0 mA 6.000 A 10.00 A
0.01 mA 0.1 mA 0.001 A 0.01 A
1.0 % + 3
1.0 % + 3
1.0 % + 3
Hz (AC...
FE 175,177,179 Users Manual - Page 18
... Scale Voltage To:
600 kΩ
50 MΩ
< 660 mV DC
< 4.6 V DC
2.4 V DC
Normal Mode Rejection
> 60 dB @ 50 Hz or 60 Hz > 60 dB @ 50 Hz or 60 Hz
Short Circuit Current...Fuse
Overload 600 mA overload for 2 minutes maximum 20 A overload for high energy circuits. Models 175, 177 & 179 Users Manual
Function Volts AC Volts DC mV/T
Overload Protection 1 1000 V RMS 1000 V RMS 1000 V RMS2
Input...
Similar Questions
No Power After Battery Change
I left my meter on volts and it sat for about 6 months when I went to use it the batteries were obvi...
I left my meter on volts and it sat for about 6 months when I went to use it the batteries were obvi...
(Posted by Ragius 6 months ago)
Works Fine With Battery But Cannot Charge The Battery By Power Supply
If the battery is charged full it works fine. the problem is we cannot chrge the battery from the po...
If the battery is charged full it works fine. the problem is we cannot chrge the battery from the po...
(Posted by rahimm 6 years ago)
When Press Power Button Lcd Screen Flash But No Power On,battery Is 100% Charged
When press power button lcd screen flash but no power on,battery is 100% chargeWhat coud be the poss...
When press power button lcd screen flash but no power on,battery is 100% chargeWhat coud be the poss...
(Posted by rubenzip71030 7 years ago)
When I Push On Button Power Not On, But Blink Green Light On Power Button
(Posted by chamith2001 9 years ago)