Eureka AirSpeed PRO ALL FLOORS Rewind Pet AS1061A Support Question
Eureka AirSpeed PRO ALL FLOORS Rewind Pet AS1061A Support Question
Find answers below for this question about Eureka AirSpeed PRO ALL FLOORS Rewind Pet AS1061A.Need a Eureka AirSpeed PRO ALL FLOORS Rewind Pet AS1061A manual? We have 2 online manuals for this item!
Question posted by Davehoope on October 6th, 2019
Power Lever Not Functioning
The Red power lever seems to not be engaging power switch
Current Answers
Answer #1: Posted by Odin on October 6th, 2019 5:01 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,670
Member since:
April 10th, 2010 Points: 41,236,670
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Eureka AirSpeed PRO ALL FLOORS Rewind Pet AS1061A Manual Pages
Owner's Guide - Page 2
.... How to clear a blockage. Each unit
is needed.
Inspection: Carefully unpack and inspect your vacuum cleaner 4 Maintain brush roll, replace U belt and how to maintain your new Eureka vacuum cleaner for assembly and use accessories 3
Automatic cord rewind, wand, crevice tool, dusting brush, turbo nozzle and stair hose.
Eureka Customer Service HELPLINE 1-800...
Owner's Guide - Page 3
...switch and unplug the electrical cord when not in this appliance has a polarized plug (one way. This plug will fit in .
If the plug does not fit fully into cord reel. If it still does not fit, contact a qualified electrician to whip when rewinding.
• Do not handle plug or vacuum... openings. Do not close a door on floor with damaged cord or plug. Do not use...
Owner's Guide - Page 4
... DCF21
Press lever to Reinstall filter. Close bottom lid until lid snaps into place. press down tab and Lift out filter and replace. READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
Replace or clean regularly to lift off pedal Brush roll cover
WAND 2
Wand 2
Turbo cover
Crevice tool Dusting brush Cord rewind switch
Power switch
Handle...
Owner's Guide - Page 5
... Attach tool to end of unit. Eureka Customer Service HELPLINE 1-800-282-2886
WAND 1
WAND 1
WAND 2
FLOORS
Fig. 2
Fig. 4 Wand 1
Wand 2 (on some models)
www.eureka.com 3 Brush roll will ...wand 1.
Do not pull past red line (Fig. 2).
• Push cord into cord clip (Fig. 3).
• To store, press switch to highest carpet setting. Do not tilt vacuum forward while using tools, always ...
Owner's Guide - Page 6
... to remove connector. Fig. 3
Fig. 4
• Rotate brush roll 2 turns to 'floors.' Pull down to lower handle flat onto floor (Fig.1).
• Remove 4 screws from brush roll cover. (Fig. 2).
• Lift...belt. Fig. 1
Fig. 2
• Remove brush roll and belt.
Make sure vacuum is turned off and power cord is unplugged. Flex the hose to clear a blockage
! Make sure end cap ...
Owner's Guide - Page 7
... of 3M Company, used in accordance with your community You must return the vacuum or vacuum part along with Eureka operating instructions. Use scissors to any consequential or incidental ...charges to the Eureka Authorized Warranty Station.
Remove 1 screw.
2) Rotate lower part of the vacuum. Warranty is a trademark of Church and Dwight Co., Inc. 3M and Filtrete are trademarks...
Owner's Guide - Page 8
... pedal to turn (on the switch. Page 4
• Check turbo nozzle for debris. Cause Power plug
Solution
• Push plug securely into hose retainer.
If the vacuum suddenly shuts off and power cord is replaced into hose retainer. Problem Motor will not rewind fully. Air path selector Belt Hose Bare floor setting
Carpet height setting Dust...
Quick Start Guide - Page 1
...vacuum, please contact our customer service helpline at left. Dry thoroughly. It is marked I for carpet or bare floors.
AS1069A Series
1STEP What's in China PN 88454
Place over carry handle. Store turbo nozzle in slots on -off for bare floors. Step on power switch...
D Snap! Do not pull past red line; Store turbo nozzle in at front; Some models: Slip wand 2 over wand 1.
Similar Questions
No Suction When In Floor Mode
My vacuum has no suction when dial is placed on "floors" mode, but the wand suction is fine when dia...
My vacuum has no suction when dial is placed on "floors" mode, but the wand suction is fine when dia...
(Posted by connie2932 1 year ago)
Power Pedal Seems To Be Loose Or Not Engaging Engine. Is There Away To Fix?
(Posted by Davehoope 4 years ago)
Cord Rewind
my cord rewind button isn't working, please help.
my cord rewind button isn't working, please help.
(Posted by jennycounsil1202 8 years ago)
Power Switch Doesn't Work
The power switch on my Eureka Airspeed Gold will not turn off the vac; I have to unplug it. Can I re...
The power switch on my Eureka Airspeed Gold will not turn off the vac; I have to unplug it. Can I re...
(Posted by jim79332 10 years ago)
How To Replace Power Switch On My Eureka Airspeed Vacuum Cleaner
How to replace The power switch on my Eureka airspeedvacumm cleaner as2013a
How to replace The power switch on my Eureka airspeedvacumm cleaner as2013a
(Posted by Martyfazio 10 years ago)