Epson TM T88II Support Question
Epson TM T88II Support Question
Find answers below for this question about Epson TM T88II - B/W Direct Thermal Printer.Need a Epson TM T88II manual? We have 2 online manuals for this item!
Question posted by rk on January 23rd, 2013
How Do You Change The Barcode To A New One
how to change to new barcode
Current Answers
Related Epson TM T88II Manual Pages
User Manual - Page 5
iii EMC and Safety Standards Applied
Product Name: TM-T88II
Model Name: M129B
The following standards are applied only to the printers that are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could void ... A
Oceania:
EMC: AS/NZS 3548
Taiwan:
EMI: Class B
WARNING
The connection of this printer will invalidate the EMC standards of a non-shielded...
User Manual - Page 9
...Introduction
Features
TM-T88II Series printers are possible by using page mode. ❏ Characters can be scaled up to a stable mechanism. Application Software
❏ Command protocol is possible by using a command.
The printers have the following features:
Printing
❏ High-speed printing: 28.4 lines/second (4.23mm (1/6") feed) maximum. ❏ Low-noise thermal printing. ❏...
User Manual - Page 26
... handshaking and parity check, as well as print density. If you find that allow you to change the near -end sensor for the paper. TM-T88II Series printers also have a near -end sensor setting. Adjustments and Settings
TM-T88II Series printers are , however, some settings for users with special requirements. There are set up at the factory...
Technical Reference - Page 3
...are registered trademarks of Seiko Epson Corporation. ESC/POS has a large number of Change Newly authorized
Rev. The functionality and the user-friendliness is compatible with its ...Moreover, its own POS printer command system (ESC/POS).
A
Page All pages
Details of commands including patented ones.
Rev. Revision History
Rev. TM-T88II/T88III Technical Reference Guide
Cautions...
Technical Reference - Page 7
... and Connectors
Appendix B Options and Consumables
Appendix C Character Code Tables
Appendix D TM-T88II/TM-88III Comparison Table
Related Software and Documents
Documents relating to obtain this Manual
This manual describes the TM-T88III, a current EPSON thermal printer product.
This manual is an OCX driver.*
Rev. TM-T88II/T88III Technical Reference Guide
About this guide.
Technical Reference - Page 9
... Consumable products 1-1 TM-T88II/TM-88III Comparison Table 1-2
Part Names and Basic Operation 1-3 Part Names 1-3 Control Panel 1-3 Power Switch 1-4 Connectors 1-5
Handling the Printer 1-5 Installing and... Switch Positions and Steps for Changing DIP Switch Settings 2-2 DIP Switch Functions 2-3
Adjusting the Roll Paper Near-End Detector 2-7 Connecting the Printer to the Host Computer 2-8
...
Technical Reference - Page 13
...: packaged power supply)
❏ Power cable model: AC-170 for PS-170. (The PS-170 and TM-T88II are no longer available. Chapter 1
Product Overview
TM-T88II/T88III Technical Reference Guide
The TM-T88III thermal printer product is obsolete and no longer being sold.)
1.1.3 Options
❏ External power supply unit
• Model PS-170 (This option has...
Technical Reference - Page 14
...; Specified paper: Thermal paper
1.1.5 TM-T88II/TM-88III Comparison Table
Table 1-1 Differences between the TM-T88II and TM-T88III
TM-T88III (current model)
1. Selecting a 2400 bps baud rate with the TM-T88III. Purchase these separately, if necessary. (The PS-170 power supply has been replaced by the driver for - the TM-T88II. Driver (EPSON OPOS ADK, Advanced Printer Driver)
38400 is...
Technical Reference - Page 15
... and Basic Operation 1.2.1 Part Names
TM-T88II/T88III Technical Reference Guide
Cutter cover Power switch
FOEEUPDATPEERRRPOORWER
Printer cover Control panel Cover open button
Figure 1-1 Printer part names
* For details on DIP switch settings, refer to "DIP Switch Positions and Steps for Changing DIP Switch Settings" (page 2-2).
1.2.2 Control Panel
TM-T88II
TM-T88III
POWER ERROR
PAPER OUT...
Technical Reference - Page 19
... cover that comes with the TM-T88II/TM-T88III onto the printer to prevent inadvertent changing of the power switch, to prevent tampering, and to replace roll paper.
1. To reset the TM printer when the power switch cover is installed, insert a long, thin object (such as the end of the printer. Insert the new roll paper following the procedure...
Technical Reference - Page 23
... Switch Functions
The DIP switch functions depend on your printer's interface specifications.
2.2.2.1 DIP switch settings for serial interface specifications Note that the settings differ on the TM-T88II and TM-T88III.))
For details on the TM-T88II and TM-88III. (The functions of receive buffer full BUSY state. Note: New DIP switch settings are the same.)
Note: * Factory...
Technical Reference - Page 24
...
SW
Function
ON
OFF
2-1
Handshake (BUSY) conditions
Receive buffer full Printer offline or receive buffer full *
2-2
Reserved (do not change setting)
Fixed to OFF
2-3, 2-4 Print density selection/low-power mode
(See separate table.)
2-5
Conditions for canceling receive buffer BUSY state (DIP SW2-5)
TM-T88II
TM-T88III
Conditions to cancel receive buffer BUSY state
Switch No...
Technical Reference - Page 25
Do not change the settings of DIP SW2-5 setting.
Rev. With the older TM-T88II model, be sure to set to 4KB. Otherwise, the printer may no longer function correctly.
2.2.2.2 DIP switch settings for other interface specifications The following DIP switch functions are reached, regardless of DIP SW2-2 and SW2-6.
A
...
Technical Reference - Page 26
... and the receive buffer is used or when TM-T88III is set to OFF before use. Do not change the settings of print density
Switch no.
When the TM-T88II is used with DIP SW1-2 set to cancel receive buffer BUSY
state
2-5
Switch no . A Otherwise, the printer may no longer function correctly.
2-6 Setup
Rev. Level...
Technical Reference - Page 29
.../XOFF
Not possible
DTR/DSR
1
-
2
-
TM-T88II/T88III Technical Reference Guide
Stand alone Both the TM printer and DM-D are connected to the TM printer over the serial interface via the serial port. Type B Type A or B
Figure 2-6 Configuration of stand-alone connection
Pass-through connection The host computer is connected to the host computer directly via DM-D.
Technical Reference - Page 39
...The functions are supported by EPSON-original Direct IO with the APD.
When you use the APD for the TM-T88III serial model or the TM-T88II, using TrueType fonts may have had to...OPOS ADK
The EPSON OPOS ADK supports the development environment required for OPOS application development using printer-resident fonts. When OPOS is used , even if they are available.
3.1.1.4 Driver information ...
Technical Reference - Page 41
... sending ESC/POS commands from the "Select any product" pull-down menu.
3.1.3 ESC/POS Commands
To directly control the TM printer using ESC/POS commands, EPSON proposes printing/ control via ESC/POS commands. Rev. TM-T88II/T88III Technical Reference Guide
• Sample programs Sample programs for the latest information.
❏ Supported development languages • Visual...
Technical Reference - Page 47
.../offline switch. A
Application Development Information 3-11 The printer automatically goes offline under the following : ❏ When the receive buffer is full ❏ When the receive buffer is full or the printer is offline
Note: In either of roll paper). TM-T88II/T88III Technical Reference Guide
3.4.3 Offline
This printer is not equipped with the paper FEED...
Technical Reference - Page 53
... write data, see the "ESC/POS Application Programming Guide." TM-T88II/T88III Technical Reference Guide
Chapter 4
ESC/POS Command-related Information
This chapter introduces the printer operation settings, which can be edited by the user.) &#...-defined command default values
You can customize your printer by changing these values. Rev. For details on how to this area is written to NV memory.
Technical Reference - Page 56
...TM-T88II/TM-T88III)
Table 5-2 Print characteristics
Characteristics
Specifications
Print method
Thermal line printing
Paper feed method
Unidirectional with friction feed
Print width
❐ 72 mm {2.84"} ❐ 50.8 mm {2.28"} (factory option with the head temperature conditions.
Line space setting: 4.23 mm {1/6"} Line space setting: 4.23 mm {1/6"}
Print speed (max.)
TM-T88II
TM...
Similar Questions
Dos Based Printing Using Epson Lx-300 + Ii Printer
Does Epson LX-300 + II printer support dos based printing? I have connected my epson lx-300 + ii pri...
Does Epson LX-300 + II printer support dos based printing? I have connected my epson lx-300 + ii pri...
(Posted by khuntetapreeti 10 years ago)
How To Change Font On This Printer
dear sir/ madam i have use in espn lq 300+II printer but not change in font priented paper pls send...
dear sir/ madam i have use in espn lq 300+II printer but not change in font priented paper pls send...
(Posted by dipsubedi23 10 years ago)
Hi I Have An Epson M129b Point Of Sale Printer.
Drivers of Epson m129b point of sale printer for windows 7 needed.
Drivers of Epson m129b point of sale printer for windows 7 needed.
(Posted by footballer 11 years ago)
My Epson Tm-t88ii Partial Cut Is Getting Paused Every Now And Then... Solution?
my EPSON TM-T88II Partial cut is getting paused every now and then... i have changed the driver also...
my EPSON TM-T88II Partial cut is getting paused every now and then... i have changed the driver also...
(Posted by sameerkhan0088 11 years ago)
Epson Modeltm-t88ii
hallo ik heb een epson printer TM-T88ii Model M129B maar ik ben de cd kwijd van de drivers kunt u m...
hallo ik heb een epson printer TM-T88ii Model M129B maar ik ben de cd kwijd van de drivers kunt u m...
(Posted by talip40 11 years ago)