Dewalt DXPW60606 Support Question
Dewalt DXPW60606 Support Question
Find answers below for this question about Dewalt DXPW60606.Need a Dewalt DXPW60606 manual? We have 1 online manual for this item!
Question posted by mkidwell on June 20th, 2017
Corrosive Deck Solution.
Where is the port for solution injection. Need to know if corrosive solution will damage the pump.
Current Answers
Related Dewalt DXPW60606 Manual Pages
Instruction Manual - Page 2
... C. Engine dipstick/oil plug H. Gas cap O. Pump
For best results, pump oil designed specifically for location and operation of other ... hose Q. Starter grip J. Handle assembly P.
Wheel E. Throttle control lever L. Engine K.
Panel assembly B. High-pressure pump
Engine
Refer to the engine instruction manual for pressure washers is not available, an SAE 30W non-detergent oil may be...
Instruction Manual - Page 3
English
Specifications
MODEL
WEIGHT
HEIGHT
WIDTH
Length
Max**
GPM**
Engine
DXPW60606 145 lbs (65.8 kg)
25.5" (64.7 cm)
28" (71.1 cm)
45" (114.3 cm)
4200 (29,... or 1-877-FNA-GAS1 (1-877-362-4271)
Important Safety Instructions
DANGER: Carbon Monoxide. You may result in property damage. If you feel sick, dizzy or weak at anytime, move to personal injury which , if not avoided, may...
Instruction Manual - Page 4
Keep operating area clear of Injection or Severe Injury. Danger: Risk of all persons.
7. WARNING: This product may also ... defined in section 4442, and maintained in the state of filler neck
explosion.
Keep good footing and balance at Persons.
Know how to avoid spilling fuel. Follow the maintenance instructions specified in a fire. Do Not Direct Discharge...
Instruction Manual - Page 5
... as siding, plastic, rubber, vinyl or the pressure hose, itself), and damage live plants) that could be damaged from muffler exhaust heat.
• Improperly stored fuel could result in serious injury or death.
• Store ... Use of acids, toxic or corrosive chemicals, poisons, insecticides, or any other corrosive compound.
5
Instruction Manual - Page 6
..., or other serious injury. The stream of water IS under high pressure and WILL penetrate skin.
• Never place hands in injection injuries. Never grasp a high-pressure hose that is damaged, worn, has melted from contacting the engine, or shows any signs of nozzle.
• Direct spray away from the...
Instruction Manual - Page 7
... chlorine
pressure washer could lead
bleach or any other
to serious injury or death to
corrosive compound. you or others.
• Become familiar with missing, broken or
unauthorized parts...
Instruction Manual - Page 8
...spray gun/wand is a powerful cleaning tool that could look like a toy to a child.
• Reactive force of Injury or Property Damage When Transporting or storing
What can happen
How to ...er
leaks. If pressure washer is felt. Only
damage the engine if the unit transport fuel in an upright position.
an upright position.
Improper ...
Instruction Manual - Page 9
...away from the pneumatic tire sidewall. Adjust pressure regulator on automobiles, trailers and the like) could damage the sidewall resulting in serious injury.
• On pressure washers rated above 1600 psi (11032 ... the control surfaces
components, could result in serious injury and property damage.
• Use a tire pressure gauge to check the tires pressure before each use ...
Instruction Manual - Page 10
...cides, or any kind of acids, toxic or
• Do not spray acids, gasoline,
corrosive chemicals, poisons, kerosene, or any electrically
cal outlets...come into contact with you or your clothing.
• Never operate with guards or covers which are damaged or removed.
• Keep your hair, clothing, and gloves away from others before lifting.
Direct
...
Instruction Manual - Page 11
... tires pressure before starting the pressure washer.
11
Adjust pressure regulator on panel assembly. English
Tools required (Not included): 1/2" (13 mm) open-end wrench 1/2" (13 mm) socket ...Assembly (DD) 4 Bolts (EE) 8 Flat Washers (FF) 4 Nuts (GG) 1. NOTE: The high-pressure pump was filled with the hardware (EE, FF, GG) from the plastic bag and insert them into place. Warning: Risk...
Instruction Manual - Page 12
... pressure may damage pump.
3. Slow the engine down and the water pressure will go down with it is capable of causing damage to surfaces ... enough to resist damage from the force of
wood or vinyl
cleaning
low pressure
applies cleaning metal, concrete,
solutions
wood or vinyl... to increase pump pressure. Reduce the speed of fluid injection. English
OPERATION
Pressure Adjustments
The pressure setting is ...
Instruction Manual - Page 13
...hose connection
of pump as garages, basements, etc.
• Never operate unit in amputation or other end of chemical/
cleaning solution will not ... fitting
located near a location occupied by loose fittings or worn or damaged hoses can kill you in injection injuries. When using the high-pressure setting, DO NOT allow the high-pressure spray to ...
Instruction Manual - Page 14
.... If applying a chemical or cleaning solution, P
refer to the ON position.
11.
Do not overfill. Turn the engine ON/OFF switch (H) to Chemicals and Cleaning Solvents.
8. Pull starter grip slowly until a steady stream
of water is left in an effort to the pump.
9. This could cause damage to lower
T
the temperature inside the...
Instruction Manual - Page 15
... Risk of clean water and draw clean water through chemical injection system to snap back.
Engine
Consult the engine instruction manual... used in unusual conditions, such as needed.
14. As the engine warms up, move the choke to the pump.
2. Engage the
X
trigger lock ... washer frame is not in the engine is running or damage to hot surfaces, water pressure or moving parts that can...
Instruction Manual - Page 16
... relieve any obstructions with the nozzle cleaning tool (Y) provided and back flush with foreign materials, such as outlined in the middle of pump.
2. Reinsert filter into spray wand to...3. Reassemble the nozzle to back flush loosened particles for 30 seconds.
6.
AA
2.
Replace pump dipstick/oil plug and tighten securely. To Clean the Water Inlet Filter
This filter screen (U)...
Instruction Manual - Page 17
... for purchase from damage. Always use of pump.
7. Reconnect spark plug wire.
When using replacement lances or guns with this tool could be performed by a FNA factory service center, ...inlet of any accessory for use a lance and/or lance/ gun combination that is corrosive and can damage pump.
2. Always store and transport unit in locating any other anti ...
Instruction Manual - Page 20
... manual for a long period of time. See Spray Wand Nozzles under Operation.
20
POSSIBLE SOLUTION Add fuel.
Engine ON/OFF switch in the No Choke position. has been exposed to ...24 Water leaking at gun/spray wand connection 25, 26 Water leaking at pump...25, 26, 27, 28 Oil leaking at pump...29, 30, 31, 32, 33, 34, 35 Pump Pulsates...12
Troubleshooting Codes
Code 1 2 3
4
5 6 7
8 ...
Instruction Manual - Page 21
... packings worn.
28
Pump head or tubes damaged from the pump inlet and turn the water source on to pump inlet and turn water... source off the engine, then the water source. Disconnect the water source from freezing.
29
Oil seals worn.
30
Loose drain plug.
31
Worn drain plug o-ring
POSSIBLE SOLUTION...
Instruction Manual - Page 22
...blow air through it to engine instruction manual for correct amount. POSSIBLE SOLUTION Check and replace. Check for correct procedure.
22 Refer to remove ...Drain and fill with oil.
English
(Troubleshooting Codes cont.)
Code possible cause
32
Worn fill plug o-ring.
33
Pump overfilled.
34
Incorrect oil used.
35
Vent plug is clogged.
36
Air filter filled with correct amount and ...
Instruction Manual - Page 68
...® and the yellow and black color scheme are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the kit box configuration; The FNA Group 1825...Elk Grove Village, IL 60007 (MAR12) Part No. 7104927 r0 DXPW60606 Copyright © 2009, 2012
The following are trademarks the DEWALT Industrial Tool Co., used under license. the "D" shaped air intake grill;
...
Similar Questions
Piston Will Not Return To Rest Position. After Pushing Piston Back With Tool, I
after pushing piston back to starting position it will then fire single nail and remain in fired pos...
after pushing piston back to starting position it will then fire single nail and remain in fired pos...
(Posted by av8trr 6 months ago)
Where Do You Plug The 30 Ft. Charger In To What Usb Port
not sure what usb port to plug the charger into computer or ? for the laser measurer
not sure what usb port to plug the charger into computer or ? for the laser measurer
(Posted by andysherrie 3 years ago)
Bolt Size For Dewalt 734 Planner Tool Tray
I need the size of the two bolts used to attach the tool tray to a 734 DeWalt Planner.
I need the size of the two bolts used to attach the tool tray to a 734 DeWalt Planner.
(Posted by luklyd 8 years ago)
Dcb 100 12v Battery Charger
Haven't used in a while. Manual M I A. How to connect battery to charger??? My thinking is the batte...
Haven't used in a while. Manual M I A. How to connect battery to charger??? My thinking is the batte...
(Posted by anotherway2live 9 years ago)
Is There Anywhere You Can Buy A Dewalt Mt16 Multi Tool Without Having To
buy it together with the MT8 as part of the DeWalt gift box set?
buy it together with the MT8 as part of the DeWalt gift box set?
(Posted by freginold 9 years ago)