Dewalt DWX726 Support Question

Find answers below for this question about Dewalt DWX726.
Need a Dewalt DWX726 manual? We have 1 online manual for this item!

Dewalt Overview Questions Manuals Reviews Videos Research

Question posted by gard2209 on March 16th, 2014

Where Is Hardware Bag?

I cannot locate the hardware bag for stand. Did not if I was over looking it. What does it include and where is it usually packaged?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by freginold on April 19th, 2014 5:53 AM

This answer was accepted by the poster of the original question.

freginold

Member since:
December 20th, 2011

Points: 23,253,885

1,100
points

Hi, the hardware bag is packaged in the carton with the pieces, and according to page 2 of the owner's manual, it contains:

- 2 cord wrap brackets (L&R)
- 6 M8 x 15mm buttonhead screws
- 1 M8 x 25mm buttonhead screw
- 6 curved washers
- 2 extension locking knobs
- 1 M8 lock washer
- 1 M6 x 10mm buttonhead screw
- 1 M6 lock washer
- 1 hex wrench

If you contact DeWalt, they may be able to send you a replacement bag.

https://configpages.blogspot.com

Related Dewalt DWX726 Manual Pages

Instruction Manual - Page 3

... the accessory. If you have any accessory. Failure to heed these symbols. When servicing this tool, use the stand for any operation for each signal word. Follow the mounting instructions carefully. Fasten the tool to the saw or planer to these warnings may result in personal injury and serious damage to personal injury...

Instruction Manual - Page 4

...: Never modify the stand or any part of the extension work support assembly 1 Handle 2 Wheel 2 Axle 2 Work support arms (1 with black cap) 1 Hardware bag: 2 Cord wrap ...brackets (L, R) 6 M8 x 15 mm buttonhead screws 1 M8 x 25 mm buttonhead screw 6 Curved washers 2 Extension locking knobs 1 M8 lock washer 1 M6 x 10 mm button head screw 1 M6 lock washer 1 Hex wrench Tools...

Instruction Manual - Page 5

... THE WHEELS (FIG. 5) 1. Place the washer (Q) on the axle with wheel extension (O) facing outward. 2. Place one M8 x 15 mm buttonhead screw (L) with curved washers (M). 3. With stand still upside down , remove washer/nut (Q, R) from the inside of the wheel hub facing inward. 3. Attach the other wheel/storage-foot connector in the same...

Instruction Manual - Page 6

...foot (C) over the indentations of the extension leg (E). 2. After raising the stand a few inches, release the red activating lever. The stand will adjust to attach storage foot and the connector. 3. English 4. Securely tighten... that were loosely installed in a raised position. 1. Use the thumb of the stand opposite the wheels with one M8 x 25 mm buttonhead screw (S) and lock washer...

Instruction Manual - Page 7

... Be sure the longer side of the "T" in the work supports from outside of the stand closest to the top piece. 2. With the stand raised to lock in Figure 9. Tighten the vertical lock knob (F). 3. Repeat for other extension... work support into the hole (W) of stand. Push the arm in to desired height, place the top piece (H1) of the...

Instruction Manual - Page 8

... the captured nut (EE). Slide the mounting rails (A) to a stand or supporting surface. IMPORTANT: The miter saw or planer off, disconnect the tool from the mounting rails. Ensure the mounting slots align the with the rail slots (DD) and the captured nuts (EE) located in Figure 16. 3. Place miter saw or planer to...

Instruction Manual - Page 9

... binding and/or inaccuracy occurs, replace the plywood with the slots in the mounting rails as the tool base being mounted and a minimum depth of the tool base you are assembling. WARNING: STABILITY HAZARD. Other hardware (not supplied) may be a minimum of 4 inch (101.6 mm) wider than the thickness of 16 inch (406...

Instruction Manual - Page 10

... tip during this same test with the block of wood under HH the front leg (GG) of serious personal injury, turn tool off and disconnect tool from power source. If the stand tends to tip to perform the stability test or serious injury could result. Make your own safety, use two or more...

Instruction Manual - Page 11

... HEIGHT 1. FIG 19 H G F 9 Refer to To Raise and Lower the Stand under Assembly to adjust the stand to Figure 19 for proper transporting position. Tighten the horizontal lock knob. 4. Turn ...the vertical lock knob (F). 2. STORAGE AND TRANSPORTATION WARNING: TIPPING HAZARD. The stand may raise unexpectedly when lever is released. TO EXTEND THE EXTENSION WORK SUPPORTS (FIG. 18)...

Instruction Manual - Page 12

...provinces. In addition to normal wear or tool abuse. For products sold in locating any defects due to accessories or damage ...caused where repairs have been made or attempted by others. To reduce the risk of injury, only DEWALT, recommended accessories should be hazardous. If you may have other rights which vary in the packaging...

Instruction Manual - Page 40

the "D" shaped air intake grill; and the array of the tool. the kit box configuration; N116787 DWX726 Copyright © 2011 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (JUN11) Part No. the array of...