Dewalt DW717 Support Question
Dewalt DW717 Support Question
Find answers below for this question about Dewalt DW717.Need a Dewalt DW717 manual? We have 2 online manuals for this item!
Question posted by kannjr on November 16th, 2015
Serial Number Location.
Hi,Where is the serial number located on the DW717?Thanks,John
Current Answers
Answer #1: Posted by freginold on November 17th, 2015 4:17 AM
freginold
Member since:
December 20th, 2011 Points: 23,253,895
Member since:
December 20th, 2011 Points: 23,253,895
Hello, the serial number should be located on the nameplate. To see the location of the nameplate, refer to this parts breakdown. (The nameplate is part #159, on the first page.)
Related Dewalt DW717 Manual Pages
Instruction Manual - Page 1
...ÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
DW717 (120 Volt), DW717 (230 Volt) 10" (254 mm) Double Bevel Sliding Compound Miter Saw
DW717 (120 Volt), DW717 (230 Volt) Scie coulissante à onglet mixte 254 mm (10 po)
DW717 (120 Voltios), DW717 (230 Voltios) Sierra ingletadora compuesta deslizante de doble bisel de 254...
Instruction Manual - Page 2
English
TABLE OF CONTENTS
DOUBLE INSULATION/POLARIZED PLUG INSTRUCTIONS 2 SAFETY INSTRUCTIONS FOR ALL TOOLS 2 ADDITIONAL SAFETY RULES 3 ELECTRICAL CONNECTION 4 ACCESSORIES ...4 BLADE DESCRIPTIONS 5 UNPACKING YOUR SAW 5 SPECIFICATIONS ...5 FAMILIARIZATION 6 BENCH MOUNTING 6 CHANGING OR INSTALLING A NEW SAW BLADE 6 REMOVING THE BLADE 6 INSTALLING ...
Instruction Manual - Page 3
... personal injury.
• MAINTAIN TOOLS WITH CARE.
Safety Instructions For All Tools
WARNING: To reduce the risk of power tools in damp or wet locations or in the outlet, reverse ... will draw. Tools built with two separate layers of power and overheating. Your shop is wider than using an extension cord, be grounded. The smaller the gauge number, the heavier the...
Instruction Manual - Page 4
...the machine and possibly causing a short which could cause your supervisor, instructor, or another tool. Clamp all blade and blade clamps are clean, recessed sides of blade clamps are recommended ... to be hazardous when used in the guard is unintentionally contacted.
• NEVER LEAVE TOOL RUNNING UNATTENDED. DO NOT USE THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE ...
Instruction Manual - Page 5
...Itasca, IL 60143-3201. WARNING: Since accessories, other injury. Use care in locating any accessory for the dust exposure.
ON UPPER GUARD: PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFORE... OPERATING SAW. DO NOT EXPOSE TO RAIN OR USE IN
DAMP LOCATIONS. Electrical Connection
Be sure your tool, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-...
Instruction Manual - Page 6
... mm)
Result Width 11.9" (302 mm) Result Height 3.0" (76 mm)
45º miter Max.
Unpacking Your Saw
Check the contents of your miter saw . 2. One DW717 miter saw carton to install. One material clamp.
BLADE DESCRIPTIONS
APPLICATION
DIAMETER TEETH
Construction Saw Blades (thin kerf with hook angles in Figure 9. 4. One DEWALT...
Instruction Manual - Page 7
....
Bench Mounting
Holes are located. Use either hole, it to rise to facilitate bench mounting, as written in laser adjustment instructions. To enhance the tool's portability, it , change...a New Saw Blade (Fig. 3)
WARNING: To reduce the risk of serious personal injury, turn off the tool and disconnect it from the bottom of 1/2" (12.7 mm) or thicker plywood which can be clamped to...
Instruction Manual - Page 9
...counterclockwise one each . In order that the saw blade is less than 45º to have the tool serviced by hand when installing or removing saw blade within 5 seconds of the saw is not adjustable. ...placed close to the blade as close to brake engagement. The blade guard on and off the tool and disconnect it from the kerf. The guard can be sure the blade has stopped before ...
Instruction Manual - Page 11
...º right or 60º left and can be removed. If small fibers of wood still split out at zero, hold the wood firmly on a number of any abrasive blades. tightened. NOTE: Although this saw back to 48º left . This angle is a commonly used technique. Ensure that each piece is...
Instruction Manual - Page 12
..., position the wood with your body and hands when operating the miter saw . As the number of your DW717. When making the cut is completed.
Rotate the clamp 180º toward the back of...
CLAMPING THE WORKPIECE
WARNING: To reduce the risk of serious personal injury, turn off the tool and disconnect it into the base.
To make any adjustments accept as a substitute for four...
Instruction Manual - Page 13
...to fit properly, crown molding must be tightened after making any other type tool made. Always try cuts on a few trial cuts. Turn on the ...saw. The chart shown on your settings anyway. Set your project and locate that fits flat against the base. Practice fitting the cut Material up...crown molding. (The numbers for the miter and bevel settings are very precise and are for ...
Instruction Manual - Page 15
...steps:
1. Avoid doing this occurs, simply place your tool. Remove both left to right. When the special set... and possible injury.
3. Periodically clean all service calls:
Model Number Serial Number Date and Place of the plastic guard. The brushes are sealed...FIG. 24
SCREWS (two each fence outward. Service center locations are packed with several years of material control and possible ...
Instruction Manual - Page 56
...., 701 East Joppa Road, Baltimore, MD 21286
(JUN08)
Part No. 658046-00
DW717
Copyright © 2008 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the kit box configuration; and the array of lozenge-shaped humps on the surface of pyramids on the...
Parts Diagram - Page 3
... 12 13 14 15 16 17 18 19 20 23 24 26 28 29 30 33 34 35
Part Number
Parts List for DW717 Type 1
Description
Qty Required
641494-00SV
ARM ASSEMBLY
1
641445-00
BELT COVER
1
330045-14
SCREW,M5 X 16MM
9
146751-00
SHAFT,PIVOT
1
146732-00
SPACER
2
150075-...
Parts Diagram - Page 4
...HANDLE
1
www.toolpartspro.com Toll Free: 800 735 8665 Fax: 760 747 2626 Email:[email protected]
Page 2 Item Number
36 37 40 41 42 43 44 45 47 48 49 50 51 52 53 54 56 57 60 62 63 ...64 65 66 67 68 70
Part Number
Parts List for DW717 Type 1
Description
Qty Required
618244-01
RETAINING PLATE
1
330045-49
SCREW
4
641477-00
PULLEY
1
153778-00
...
Parts Diagram - Page 5
...84 85 86 88 89 90 91 92 93 94 95 96 98 99 100 101
Part Number
330016-03 618148-00 603636-00 330045-06 618160-00 626440-00 098103-18 098104-17 ...25 330015-03 391346-00 641486-00 641416-00 641453-00 641498-00 330045-05 049787-00 098025-35 641449-00
Parts List for DW717 Type 1
Description
Qty Required
WASHER,PLAIN
3
LOCK ROD
1
THRUST WASHER
1
SCREW
11
BLOCK
1
SPRING
1
SCREW
4
SCREW
...
Parts Diagram - Page 6
...119 120 121 123 124 125 126 127 128 129 130 131 132 133
Part Number
153792-00 641443-00 604410-00 391358-01 608563-01 641452-00 641446-00 330045...624730-00 330045-18 330019-32 618270-00 606056-00 384127-01 330045-25 640056-00 660015-02 641438-00
Parts List for DW717 Type 1
Description
Qty Required
WASHER
2
DETENT PLATE
1
SCREW
4
WRENCH HOLDER
1
WRENCH
1
POINTER
1
ACTUATOR
1
SCREW
...
Parts Diagram - Page 7
... 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160
Part Number
Parts List for DW717 Type 1
Description
Qty Required
330019-22
SCREW
1
659008-00
CABLE CLAMP
1
618213-00
JUMPER
1
641430-00
COVER
1
641411-00
FENCE
1
641474-00
LEFT...
Parts Diagram - Page 8
...182 183 200 201 202 203 204 205 206 207 208 209 212 213 214
Part Number
330045-13 330019-12 641496-00 603390-00 397118-00 153576-04 613497-00 153586-00...386780-00 641434-00 641433-00 385915-04 641432-00 146768-00 641436-00 146750-03 661454-00 148295-00
Parts List for DW717 Type 1
Description
Qty Required
SCREW,TAPTITE
3
SCREW
3
TRUNNION ASSY
1
SCREW
8
GUIDE
3
SET SCREW
1
SLUG
1
...
Parts Diagram - Page 9
... 229 239 240 241 242 243 244 245 247 248 249 250 251 252
Part Number
625825-00 142273-00 394976-00 618234-00 153666-00 618274-00 145332-00 450212-...-00 618277-00 618278-00 641427-00 616001-00 641482-00 641481-00 641483-00 641421-00 641423-00
Parts List for DW717 Type 1
Description
Qty Required
ROLLER
2
RING,RETAINING
5
LABEL, CAUTION
2
STUD
1
SCREW,SET
4
WARNING LABEL
2
TERMINAL...
Similar Questions
Part Number
What is the part number of the engine cover that contains the oil stick? Mine crtacked
What is the part number of the engine cover that contains the oil stick? Mine crtacked
(Posted by spknkdog 3 years ago)
Part Number For Compression Ring On D55168 T5
Ok I have a D55168 T5 The compression ring in the sleeve has a blown spot so I need to replace it I ...
Ok I have a D55168 T5 The compression ring in the sleeve has a blown spot so I need to replace it I ...
(Posted by Anonymous-159859 7 years ago)
Problem With The Serial Number In My Dws780 . There Only A Few Numbers
(Posted by imagemind 8 years ago)
What Are Part Numbers For The Dewalt D28715 Optional 'keyed Blade Clamp System'?
What are the part numbers for the Dewalt D28715 optional "Keyed Blade Clamp System"?This extra-cost ...
What are the part numbers for the Dewalt D28715 optional "Keyed Blade Clamp System"?This extra-cost ...
(Posted by jamesaderr 9 years ago)