Dewalt DW717 Support Question
Dewalt DW717 Support Question
Find answers below for this question about Dewalt DW717.Need a Dewalt DW717 manual? We have 2 online manuals for this item!
Question posted by Garycrewe on April 7th, 2015
Led Light Stopped Working
I have just bought a dw717xps I plugged it in to the power supply and switched it on the light lit up so I switched it off and the switched it back on but the light didn't and won't come back onIs there something I'm doing wrong
Current Answers
Related Dewalt DW717 Manual Pages
Instruction Manual - Page 1
... PRODUCTO. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.
Questions?
DW717 (120 Volt), DW717 (230 Volt) 10" (254 mm) Double Bevel Sliding Compound Miter Saw
DW717 (120 Volt), DW717 (230 Volt) Scie coulissante à onglet mixte 254 mm (10 po)
DW717 (120 Voltios), DW717 (230 Voltios) Sierra ingletadora compuesta deslizante de doble bisel de 254...
Instruction Manual - Page 2
English
TABLE OF CONTENTS
DOUBLE INSULATION/POLARIZED PLUG INSTRUCTIONS 2 SAFETY INSTRUCTIONS FOR ALL TOOLS 2 ADDITIONAL SAFETY RULES 3 ELECTRICAL CONNECTION 4 ......8 BEVEL STOP...8 FENCE ADJUSTMENT 8 AUTOMATIC ELECTRIC BRAKE 8 GUARD ACTUATION AND VISIBILITY 8 KERF PLATE ADJUSTMENT 9 RAIL GUIDE ADJUSTMENT 9 MITER LOCK ADJUSTMENT 9
BRUSHES 9 CONTROLS ...9 OPERATION 9
SWITCH...9 CUTTING ...
Instruction Manual - Page 3
...THE POWER SOURCE before installing or removing accessories, before plugging in good condition. No loose clothing, gloves, neckties, rings, bracelets, or other ) are constructed throughout with a two prong plug which , if not avoided, may cause personal injury.
• MAINTAIN TOOLS WITH CARE. Non-slip footwear is dusty. Everyday eyeglasses are removed from work area well-lit...
Instruction Manual - Page 4
...LOCK THE SWITCH IN THE "ON" position. Do not use tool if switch does not turn it comes to ...tool and personal injury may cause risk of your hand to operation. Hold the work...TURN POWER OFF. Protect electric supply line with any other part that may cause damage to the power ... SLOTS of the tool, a guard or other conditions that is subject to a complete stop.
Starting the cut...
Instruction Manual - Page 5
...tool. English
• TURN OFF THE MACHINE and allow the blade to come to a complete stop before raising the arm and prior to ANSI S12.6 (S3.19) during use. a safety video) is suseptible to hearing loss. Department of power...work supports; Laser Guide System: DW7187
Powered by DEWALT, have not been tested with this tool does not operate, check the power supply. Easy to accept two work...
Instruction Manual - Page 6
...320 mm) Result Height 2.0" (50 mm)
DW7080 END PLATE LOCKNUTS
DW7082
5
DW7084 DW7187
DWS7085 One DW717 miter saw blade. 3.
Height 2.3" (58 mm) Result Width 11.9" (302 mm) Max. SPEED... 5000 RPM.
One material clamp. Height 3.5" (89 mm) Max. Miter Saw LED Worklight System: DWS7085
Lighting used for ripping, combination blades or blades with anti-stick rim)
General Purpose
10...
Instruction Manual - Page 7
...power or
coasting.
• Do not cut ferrous metal (containing
iron or steel) or masonry or fiber
A
cement product with the proper operation of the saw blade by 4.75" (120 mm)
tall.
To enhance the tool...in Figure 2. FIG. 2
Press down lightly on the clamping bosses where the mounting screw...depressed, use both.) Always mount your work support.
Assemble the outer blade clamp...
Instruction Manual - Page 8
...
KERF PLATE
MITER LATCH BUTTON
BEVEL LATCH PLATES
TRIGGER SWITCH
BELT COVER DUST SPOUT
RAILS
FENCE ADJUSTMENT
KNOB (ONE... HOLES
MITER LATCH OVERRIDE MITER LOCK HANDLE
HAND INDENTATION
FENCE
GROOVING STOP
5. MITER SCALE ADJUSTMENT (FIG. 5)
Place a square against ...serious personal injury, turn off the tool and disconnect it from the power source before attempting to shipping and handling...
Instruction Manual - Page 9
... it is equipped with sawdust. To align the 45º stops, lock the arm in Figure 6. If the saw blade within 5 seconds of the guard is 45º to have the tool serviced by giving the saw your saw blade is placed close...persists, have the square not touch a blade tooth. The guard can be pinched between it from the power source before removing it and the table.
English
Instruction Manual - Page 10
... screwdriver, tighten the miter lock rod by unplugging tool, removing the motor end cap (Fig. 4), ... housing.
Adjust so that it from the power source before use a 4 mm hex wrench...work. BEVEL CONTROL (FIG. 8) The bevel latch levers and bevel lock handle allow the brake to either side of the saw on , depress the trigger switch. ALWAYS TIGHTEN THE RAIL LOCK KNOB WHEN USING THE SLIDE STOP...
Instruction Manual - Page 11
...come to a full stop before raising arm. With the rail lock knob tightened, turn on the saw comes up to speed (about 1 second) lower the arm smoothly and slowly to slide along its rails.
When the saw by squeezing the trigger switch...of wood still split out at any angle. If small fibers of variables. Do not use a work , a sharp (60 tooth carbide) blade and a
10
FIG. 13A
PROPER CUT FIG. ...
Instruction Manual - Page 12
...supplied with the broad surface against the fence. SUPPORT FOR LONG PIECES WARNING: To reduce the risk of serious personal injury,
turn off the tool and disconnect it from the power... and the blade has completely stopped.
Ensure this groove is firmly... to the base of the work area. EXAMPLES - Always clamp...purchase the DW7082 contact your DW717. The left with your local...
Instruction Manual - Page 13
.... 19
FENCE FIG. 20
RIGHT
BLADE
BLADE
FENCE
WRONG
angle and bevel stop pawls at 45°
FIG. 17
FENCE TABLE
...at 45° 2. CUTTING BASE MOLDING ALWAYS MAKE A DRY RUN WITHOUT POWER BEFORE MAKING ANY CUTS. Straight 90º cuts:
Position the wood against...1. These knobs must be tightened after making any other type tool made. Find 26° on saw (18°). Always ...
Instruction Manual - Page 15
.... 26
SCREWS
BACK FENCE SCREWS
SET SCREW
14
the work. To set the saw up just enough to clear the workpiece, as shown in the material coming loose and causing injury. To remove them into two ...otherwise the material will operate properly and make the bigger cut on Page 9 or return the tool to the nearest service center for these workpieces, follow the instructions on top of wood a ...
Instruction Manual - Page 16
... blade around, see Page 8.
4.
Contact your DEWALT Power Tool, Laser, or Nailer for any reason, you may be ...plugged in saw blade
3. Have cord replaced by normal use identical replacement parts. Incorrect blade for work bench
Page 6.
2. BLADE DOES NOT COME...work being done 4. Cord damaged
3. Change the blade type, see Page 7. 2. Stand or bench on Page 13.
15
WHAT'S WRONG...
Instruction Manual - Page 56
... on the handgrip; the kit box configuration; the "D" shaped air intake grill; the array of the tool. DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
(JUN08)
Part No. 658046-00
DW717
Copyright © 2008 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme;
Parts Diagram - Page 3
... Number
1 2 3 4 5 7 8 9 10 12 13 14 15 16 17 18 19 20 23 24 26 28 29 30 33 34 35
Part Number
Parts List for DW717 Type 1
Description
Qty Required
641494-00SV
ARM ASSEMBLY
1
641445-00
BELT COVER
1
330045-14
SCREW,M5 X 16MM
9
146751-00
SHAFT,PIVOT
1
146732-00
SPACER
2
150075...
Parts Diagram - Page 4
... 45 47 48 49 50 51 52 53 54 56 57 60 62 63 64 65 66 67 68 70
Part Number
Parts List for DW717 Type 1
Description
Qty Required
618244-01
RETAINING PLATE
1
330045-49
SCREW
4
641477-00
PULLEY
1
153778-00
SCREW
2
98198-05
WASHER
2
153782-00
WASHER
2
641495-00SV...
Parts Diagram - Page 5
... 98130-25 330015-03 391346-00 641486-00 641416-00 641453-00 641498-00 330045-05 049787-00 098025-35 641449-00
Parts List for DW717 Type 1
Description
Qty Required
WASHER,PLAIN
3
LOCK ROD
1
THRUST WASHER
1
SCREW
11
BLOCK
1
SPRING
1
SCREW
4
SCREW
2
DETENT SPRING
1
PAWL
1
LEVER
2
ROD
1
TORSION SPRING
1
CAM
1
DETENT...
Parts Diagram - Page 6
...-00 606056-00 384127-01 330045-25 640056-00 660015-02 641438-00
Parts List for DW717 Type 1
Description
Qty Required
WASHER
2
DETENT PLATE
1
SCREW
4
WRENCH HOLDER
1
WRENCH...PIVOT PIN
1
SLEEVE
1
ROD
1
BLOCK
1
SPRING
1
HANDLE SET
1
SCREW
4
SCREW
5
COVER
1
SWITCH
1
SCREW
4
SCREW,TAPTITE
1
MOTOR CORD
1
CORDSET
1
HANDLE,CARRYING
1
www.toolpartspro.com Toll Free: ...
Similar Questions
Crown Molding Stops
Can I purchase crown molding stops to fit the DW 713?
Can I purchase crown molding stops to fit the DW 713?
(Posted by Workr247 2 years ago)
Dwp849 Worked Yesterday Today Nothing Like Its Not Plugged In
I have checked cord to switch but dont have info on it or the other 2 components so called service c...
I have checked cord to switch but dont have info on it or the other 2 components so called service c...
(Posted by svpledger 7 years ago)
Serial Number Location.
Hi,Where is the serial number located on the DW717?Thanks,John
Hi,Where is the serial number located on the DW717?Thanks,John
(Posted by kannjr 8 years ago)
Why Has It Stopped Working?
It was working fine, then vibrated, then stopped working. Please help!
It was working fine, then vibrated, then stopped working. Please help!
(Posted by deniselaw 10 years ago)