Dewalt DW505 Support Question
Dewalt DW505 Support Question
Find answers below for this question about Dewalt DW505.Need a Dewalt DW505 manual? We have 1 online manual for this item!
Question posted by mdziadziomaui on May 6th, 2013
Motor Works, But No Gear Turning Occuring
My DW505 stopped working this weekend. When I hold the switch down it works as normal and then when I go to engage the bit into the concrete it doesn't have enough torx. Would that be a chuck issue? Bearing Issue? Brush issue or all some of them? Please let me know I have several more holes to drill to set screws in place. Thanks
Current Answers
Related Dewalt DW505 Manual Pages
Instruction Manual - Page 12
...risk of electric shock if your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1) WORK AREA SAFETY a) Keep work area clean and well lit. Use of electric shock.
Protective ... or under the influence of flammable liquids, gases or dust.
f) If operating a power tool in the presence of drugs, alcohol or medication. Always wear eye protection. WARNING: To ...
Instruction Manual - Page 13
...switch is in moving parts. Carrying power tools with these instructions taking into account the working conditions and the work to power source and/ or battery pack, picking up or carrying the tool. d) Remove any adjusting key or wrench before turning the power tool...idle power tools out of the reach of starting . e) Maintain power tools. g) Use the power tool, accessories and tool bits etc., ...
Instruction Manual - Page 14
...promote absorption of use . Under some conditions and duration of harmful chemicals. Holding the work in loss of work with approved safety equipment, such as those dust masks that conforms to ... to these exposures varies, depending on how often you do this tool can cause permanent eye damage.
• Bits and tools get into your body is recommended to hearing loss. Wear gloves when...
Instruction Manual - Page 15
... in Figure 1
and can cause injury. alternating current
... per minute sfpm .... To stop hammerdrill, release the trigger switch. Side Handle (Fig. 1)
WARNING: To reduce the risk of
control. Damage or personal injury could result. To turn unit off and disconnect tool from a locked-on condition, squeeze and release the trigger once. All users and...
Instruction Manual - Page 16
...switch the tool from the chuck end). REVERSING LEVER The reversing lever is toward the front of accessories. High/Low Speed Operation (Fig. 3)
The two speed gear drive in Figure 2. To position the lever for backing out screws or jammed bits... the chuck slightly by turning the shift knob when the tool is toward the front of the hammerdrill. The farther the trigger switch is located...
Instruction Manual - Page 17
... operable positions between the two. Place chuck key in just one hole, then loosen the chuck by turning collar with both hands to control the twisting action of injury, turn collar key counterclockwise in each of bit about 3/4" (19 mm) into chuck. OPERATION
WARNING: To reduce the risk of the drill.
4. Hold tool firmly with fingers counterclockwise (when...
Instruction Manual - Page 18
...Work that the bit is sharp. For holes larger than those offered by DEWALT, have not been tested with this tool... turn unit off and disconnect tool ...bits rated for metal. English
18 For holes up to full power while applying firm pressure on the tool. never immerse any liquid get inside the tool;
Start drilling with depth rod, stop...low-speed gear range. Your DEWALT power tool has ...
Instruction Manual - Page 19
... replacement, or if it with normal household waste.
Local regulations may provide... RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be disposed of electrical...working life. Should you find one day that will collect them on our behalf. MAXIMUM RECOMMENDED CAPACITIES DW505
CHUCK CAPACITY
1/2" (13 mm)
R.P.M.
0-1,100 - 0-2,700
BITS...
Instruction Manual - Page 22
... #6001 EDIFICIO 67 CONCHALI-SANTIAGO CHILE
HECHO EN MÉXICO MADE IN MEXICO
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
(NOV11)
Part No. the "D" ..., ACCESO RADIATAS NO.42
3A. AVDA. N142137
DW505
Copyright © 2003, 2006, 2011 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; SOLAMENTE PARA...
Similar Questions
The Motor Runs But The Hammer Does Not Activate
the motor seems to be fine but it appears the clutch does not engage
the motor seems to be fine but it appears the clutch does not engage
(Posted by mrclnixon 1 year ago)
Dewalt Spade Drill Have No Torque Power
Dewalt spade drill has no torque power. When I want to mix something like concrete or mortar, it spi...
Dewalt spade drill has no torque power. When I want to mix something like concrete or mortar, it spi...
(Posted by goldskulltula 2 years ago)
Tough System Music Dead
hi was working ok turned of power for lunch came back and dead.are there any reset buttons or help f...
hi was working ok turned of power for lunch came back and dead.are there any reset buttons or help f...
(Posted by Johnpellegrino43 4 years ago)
Need Wire Diagram For Trigger On Dw505
need wire diagram for trigger on dw505
need wire diagram for trigger on dw505
(Posted by fsever1963 5 years ago)
I Need The Electrical Wiring Diagram For My Dewalt Dw505 Hammer Drill. Mike
(Posted by jmandrews49 10 years ago)