Dewalt DW505 Support Question
Dewalt DW505 Support Question
Find answers below for this question about Dewalt DW505.Need a Dewalt DW505 manual? We have 1 online manual for this item!
Question posted by fsever1963 on May 16th, 2018
Need Wire Diagram For Trigger On Dw505
need wire diagram for trigger on dw505
Current Answers
Answer #1: Posted by Odin on May 16th, 2018 11:57 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Dewalt DW505 Manual Pages
Instruction Manual - Page 12
...Read all safety warnings and all instructions Failure to lose control.
2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Unmodified plugs and matching outlets will result in any adapter plugs ... each signal word.
Keep cord away from heat, oil, sharp edges or moving parts. Power tools create sparks which may ignite the dust or fumes.
3) PERSONAL SAFETY a) Stay alert, watch ...
Instruction Manual - Page 13
... misalignment or binding of moving parts, breakage of parts and any other condition that the safety of the power tool is dangerous and must be caught in the hands of the power tool "live " wire may result in the off .
Loose clothes, jewellery or long hair can cause personal injury.
• Hold power...
Instruction Manual - Page 14
... to make up the total length, be sure each individual extension contains at least the minimum wire size. When using more than one extension to get hot during use. To reduce your body...dry, clean, free from face and body. it is recommended to loss of the tool.
• An extension cord must have adequate wire size for the dust exposure. If in loss of these chemicals are:
• lead...
Instruction Manual - Page 15
... time), be rotated 360˚ for right- DO NOT lock the switch on condition, squeeze and release the trigger once. WARNING: Always use . To stop hammerdrill, release the trigger switch. The tool will cause the hammerdrill to release the locking mechanism before making any adjustments or removing/installing attachments or accessories. The locking...
Instruction Manual - Page 16
... for using abrasive and polishing accessories. It may be necessary however, to rotate the chuck slightly by turning the shift knob when the tool is located above the trigger, shown in the dual range hammerdrill permits effective operation over an extended range of applications with greater selection of the hammerdrill.
NOTICE: DO...
Instruction Manual - Page 17
... Place chuck key in each of stalling. DO NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL -
There are no need to center punch the point to stall the motor or deflect...: To reduce the risk of bit about 3/4" (19 mm) into chuck. Hold tool firmly with the bit. RELEASE TRIGGER IMMEDIATELY, remove drill bit from the chuck end) and insert shank of personal injury,...
Instruction Manual - Page 18
... metal.
Start drilling with slow speed and increase to full power while applying firm pressure on the tool to 3/8" (10 mm) diameter use of such accessories with a block of maintenance. DRILLING IN MASONRY...
When drilling in and around the air vents. Use a constant and firm force on the tool. Depth Rod
To adjust the depth rod, loosen the handle and move rod so that is seen...
Instruction Manual - Page 19
...Should you purchase a new product. Voltage: Power-Watts: Frequency: Power: Strokes per minute:
SPECIFICATIONS DW505-AR 220V~ 700W 50 Hz 0-1000 / 0-2700/min 0-19000 / 0-46000
DW505-B2 220V~ 700W 50-60 Hz 0-1000 / 0-2700/min 0-19000 / 0-46000
Voltage: Power... materials to any authorized service center that your DEWALT product needs replacement, or if it with normal household waste.
Instruction Manual - Page 22
... M. #6001 EDIFICIO 67 CONCHALI-SANTIAGO CHILE
HECHO EN MÉXICO MADE IN MEXICO
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
(NOV11)
Part No. SECCIÓN DE..."D" shaped air intake grill; DE C.V. N142137
DW505
Copyright © 2003, 2006, 2011 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme;
SOLAMENTE...
Similar Questions
Wiring Diagram For The Switch Wire Positions On A Dewalt Dw130v Drill
Red, blue, white and black wires. What positions do they connect in?
Red, blue, white and black wires. What positions do they connect in?
(Posted by Timdzeigler77 4 years ago)
Wiring Diagram For Dewalt Drill Dw511
replaced trigger in drill and lost location of wires were they go on trigger. please help thanks mik...
replaced trigger in drill and lost location of wires were they go on trigger. please help thanks mik...
(Posted by monsterrobotshop 6 years ago)
I Need The Electrical Wiring Diagram For My Dewalt Dw505 Hammer Drill. Mike
(Posted by jmandrews49 10 years ago)
Motor Works, But No Gear Turning Occuring
My DW505 stopped working this weekend. When I hold the switch down it works as normal and then when ...
My DW505 stopped working this weekend. When I hold the switch down it works as normal and then when ...
(Posted by mdziadziomaui 10 years ago)