Dewalt D55168 Support Question
Dewalt D55168 Support Question
Find answers below for this question about Dewalt D55168.Need a Dewalt D55168 manual? We have 4 online manuals for this item!
Question posted by dewaltwalt on December 2nd, 2014
Service Manual For Dewalt D55168 Type 6?
The person who posted this question about this Dewalt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by AdachyBaby on December 7th, 2014 10:05 PM
AdachyBaby
Member since:
November 18th, 2014 Points: 23,160
Member since:
November 18th, 2014 Points: 23,160
You can probably find the document you are looking for at this page:
Related Dewalt D55168 Manual Pages
Instruction Manual - Page 2
... Specifications
Voltage: Single Phase 120V Minimum branch circuit requirement: 15 A Fuse Type: Time delay
Specifications
MODEL WEIGHT HEIGHT WIDTH LENGTH AIR TANK CAPACITY (GALLONS)... CUT-IN PRESSURE APPROX. Regulated Pressure Gauge D. Pressure Regulator E. CUT-OUT PRESSURE SCFM @ 90 PSI (620.5 kPa)
D55168 88 lbs. (39.92 kg) 41.75" (1060.5mm) 19.0" (482.6 mm) 21.25 (539.8 mm)...
Instruction Manual - Page 3
... OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)
Important Safety Instructions
WARNING: Do not operate this unit until you do this instruction manual for each ...risk of of California to the State of personal injury. Please read and understand this type of combustible materials, gasoline, or solvent vapors.
3 DANGER: Indicates an imminently hazardous situation...
Instruction Manual - Page 5
All pressure vessels should be performed by a DEWALT factory service center or a DEWALT authorized service center in serious injury or death by electrocution. Attachments ...IT
• Failure to properly drain condensed water from air tank, causing rust and thinning of air tools, spray guns, air operated accessories, tires, and other inflatables can result in accordance with national and ...
Instruction Manual - Page 6
... part of the body or at high speed, resulting in serious injury or death from the air hose and air tank before attempting maintenance, attaching tools or accessories. HOW TO PREVENT IT
• Always wear certified safety equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3) with guards or covers which the...
Instruction Manual - Page 7
... causing damage to the compressor and could lead to seri-
others.
• Become familiar with missing, broken, or unauthorized parts. Never operate compressor on this manual.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
7
English
• Attempting to operate compressor with damaged or missing parts or attempting to repair compressor with protective shrouds...
Instruction Manual - Page 9
... or disconnecting to ensure coupler is equipped with a cord having a
grounding wire with all local codes and ordinances.
2. English
MOTOR OVERLOAD PROTECTOR The motor has a manual thermal overload protector. INSTALLATION
Assembly
INSTALLING HOSES WARNING: Risk of unsafe operation. Firmly grasp hose in doubt as the
grounded plug.
Pull coupler on Quick...
Instruction Manual - Page 11
...are not closely followed. Ensure the drain valve (H) is put into service for the first time and when the check valve or a compressor pump... body, pull coupler back until you read and understand this instruction manual for pulling the unit up and down stairs
O
or steps. ... be lifted or pushed up
a ramp.
1. Some air tools and accessories may contain water condensation and oil mist.
Do ...
Instruction Manual - Page 12
... OFF position. The tank will be followed when maintenance or service is normal to desired setting. Some air operated tools or devices may contain water condensation and oil mist. Shut... cut -out pressure. After 15 minutes, close the drain valve by a DEWALT factory service center or a DEWALT authorized service center.
12 Compressed air will fill to escape and prevent air pressure build ...
Instruction Manual - Page 13
...switch (A) is in removing moisture, dirt, etc.
Risk of unsafe operation. Allow unit to
servicing.
1. Remove element from air tank. 6. Use ANSI S12.6 (S3.19) ear protection as...(A) is in accordance with the same type of valve.
Air tanks contain high pressure air. Remove filter cover (N) from your local dealer or authorized
N
service center. Always use
Every 100 hours...
Instruction Manual - Page 14
... INTAKE AND EXHAUST VALVES
Once a year have been made or attempted by a DEWALT factory service center, a DEWALT authorized service center or other accessory not recommended for all service calls: Model Number Serial Number Date and Place of purchase. CAUTION: The use with this tool could be performed by others.
Snap filter cover to accessories or damage...
Instruction Manual - Page 16
... On/Off switch to OFF, if the unit does not shut
reaches cut-out pressure
off contact a DEWALT factory service center or a DEWALT
authorized service center.
2
Pressure switch cut-out too high
Contact a DEWALT factory service center or a DEWALT authorized service center.
3
Tube fittings are not tight enough
Tighten fittings where air can perform some corrective actions, and...
Instruction Manual - Page 17
Operate safety valve manually by your air compressor, a larger compressor is needed to Motor Overload Protection under Features. ...bursting. If it is higher than the CFM or pressure supplied by pulling on ring.
English Contact a DEWALT factory service center or a DEWALT authorized service center. It is normal for some pressure drop to occur when an accessory is used, adjust the regulator...
Instruction Manual - Page 18
.... Check for proper fuse.
Check wiring connection inside pressure switch and terminal box area.
if the valve does not open, replace switch.
1. Contact a DEWALT factory service center or a DEWALT authorized service center.
Reset circuit breaker.
Do not use a time delay fuse.
3. Disconnect the other electrical appliances from circuit or operate the compressor on the...
Instruction Manual - Page 56
the array of the tool. the kit box configuration; DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286 (AUG06) Form No. A18764 D55168 Copyright © 2006 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; and the array of lozenge-shaped humps on the surface of pyramids on...
Parts Diagram - Page 2
Parts list, pricing, and availability subject to change. Please visit www.dewaltservicenet.com for D55168 Type 5
Description
Qty Required
A16537
TANK ASSEMBLY
1
N008517
WHEEL
2
A01194
BOLT .375-16X2.38 UN
2
SSF-8111-ZN
NUT .375-16 HEX WHIZ
2
SST-5314-1
BUMPER ...
Parts Diagram - Page 3
... LABEL
1
LABEL
1
LABEL
1
LABEL POWER CORD TRI
1
WARNING LABEL
1
LABEL
1
SPEC INFO LABEL
1
COPYRIGHT© 2005. All Rights Reserved. Please visit www.dewaltservicenet.com for D55168 Type 5
Description
Qty Required
REGULATOR BONNET
1
KNOB
1
REGULATOR/MANIFOLD
1
GAUGE
1
FITTING
1
GAUGE
1
MICRO PRESS. Item Number
27 27 27 28 29 30 31 32 33 35...
Parts Diagram - Page 4
Please visit www.dewaltservicenet.com for D55168 Type 5
Description
Qty Required
PLUG PIPE
2
BODY QC .250 IND .25
1
BRUSH
2
BRUSH SPRING
2
BELT
1
FAN
1
SCREW
1
MOTOR PULLEY
1
FLYWHEEL
1
CONN ROD/PISTON ASSY
1
SCREW
1
IDLER ...
Similar Questions
Dewalt D55168 Air Compressor Not Turning On.
I have a DeWalt D55168 air compressor that is not turning on. The circuit was not tripped. The outle...
I have a DeWalt D55168 air compressor that is not turning on. The circuit was not tripped. The outle...
(Posted by rjmsteen 2 years ago)
Part Knob Fits Onto
Looking for a part that the knob screws on to the regulator, not the kit.
Looking for a part that the knob screws on to the regulator, not the kit.
(Posted by suzettetbo 2 years ago)
Part Number For Compression Ring On D55168 T5
Ok I have a D55168 T5 The compression ring in the sleeve has a blown spot so I need to replace it I ...
Ok I have a D55168 T5 The compression ring in the sleeve has a blown spot so I need to replace it I ...
(Posted by Anonymous-159859 7 years ago)
