Dewalt D55168 Support Question
Dewalt D55168 Support Question
Find answers below for this question about Dewalt D55168.Need a Dewalt D55168 manual? We have 4 online manuals for this item!
Question posted by JC19505 on December 15th, 2016
Pressure Switch Not Working
My compressor is about three years old & only gets used 3-5 times a year. Now, it wont shut down when the pressure reaches 200lbs, has gone as high as 220 lbs & I manually shut it off, this is a real PITA. I removed the cover on top but found no standard pressure switch as I had on previous compressors & assume it is somehow internal in the motor housing. Any thoughts?Thanks,Jim Carpentere-mail [email protected]
Current Answers
Answer #1: Posted by BusterDoogen on December 15th, 2016 4:27 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
Go here for the regulator kit # N008792.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Dewalt D55168 Manual Pages
Instruction Manual - Page 2
Pressure Regulator E. English
D55168 Air Compressor
A. Quick Connect
F. Safety Valve H. CUT-OUT PRESSURE SCFM @ 90 PSI (620.5 kPa)
D55168 88 lbs. (39.92 kg) 41.75" (1060.5mm) 19.0" (482.6 mm) 21.25 (539.8 mm) 15 Gallon (56.8 liters) 160 PSI (1103.2 kPa) 200 PSI (1379.0 kPa) 5.4
FIG. 1
2
B C
I . Air Tank Drain Valve
I A G
D E
F
H Pressure Switch
Pump/Motor Specifications...
Instruction Manual - Page 3
... California to spark.
• Always operate the compressor in death or serious injury. CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which , if not avoided, will result in a well ventilated area free of severity for electrical contacts within the motor and pressure switch to cause cancer, and birth defects or other...
Instruction Manual - Page 4
... to human consumption.
• Sprayed materials such as paint, paint solvents, paint remover, insecticides, weed killers, may contain carbon monoxide, toxic vapors, or solid particles from spray area. To reduce the risk of this compressor for the materials you are spraying. The air stream may contain harmful vapors and poisons.
• Work in use.
Instruction Manual - Page 5
... protective covers removed or damaged.
• Any electrical wiring or repairs required on your state pressure vessels inspector, look under the Division of Labor and Industries in the government section of the steel air tank.
• Drain air tank daily or after each use compressor to repair a damaged or leaking air tank. Never attempt to...
Instruction Manual - Page 6
... Grounding: Failure to provide adequate grounding to which are damaged or removed.
• Keep your clothing.
• Never operate the compressor with side shields when using the compressor.
• Never point any nozzle or sprayer toward any part of the body or at high speed, resulting in serious burns.
• Never touch any exposed metal...
Instruction Manual - Page 8
... to the pressure switch and OFF to remove power at the base of each use .
The cooling system is working when air is used to drain condensation at the end
cut-out pressure setting, the safety valve (G) will be heard leaking when the motor is not
TANK PRESSURE GAUGE
D
The tank pressure gauge (B) indicates the B
available until the compressor has...
Instruction Manual - Page 9
...pressure gauge reads 0 PSI (0 kPa). 2. Pull coupler on Quick Connect body back to whether the compressor is equipped with a cord having a
grounding wire with a grounded outlet
(K).
Ensure the outlet being used... electrician. DO NOT USE AN ADAPTER.
3. Set...2. Coupler will shut off the motor. Ensure regulated pressure gauge reads 0...Do not use .
This plug
M
MUST be used , be ...
Instruction Manual - Page 10
... On/Off switch (A) to prevent tipping the unit over in the vehicle. TRANSPORTING When transporting the compressor in a vehicle, trailer, etc., make sure the tank is drained and the unit is secured with the flow of air. Use care when driving to the OFF position before using an extension cord, increase the working reach of using unit...
Instruction Manual - Page 11
... tools and accessories. DO NOT lift
by moisture. Ensure the drain valve (H) is reached push knob in the OFF position. When the desired pressure is closed. 5. BREAK-IN PROCEDURE WARNING: Risk of unsafe operation.
English
LIFTING
Always use caution when rolling compressor so that could be lifted or pushed up
a ramp.
1. Ensure the On/Off switch...
Instruction Manual - Page 12
... to cool down. 6. Move the On/Off switch to cut -out pressure. The tank will stop when tank pressure reaches cut -out pressure and the motor will fill to the ON position.
CAUTION: Risk of unsafe operation. NOTE: If finished using compressor, follow Steps 2 - 6. Remove hose and accessory. Ensure air tank pressure gauge reads 0 PSI (0 kPa). Water will start...
Instruction Manual - Page 13
.... 2). Purchase replacement parts
from noise. If the safety valve does not work properly, over-pressurization may be regulated and must be difficult to make sure that accumulates in removing moisture, dirt, etc.
Draining Air Tank (Fig. 1)
WARNING: Risk of burn. Air tanks contain high pressure air. Allow unit to catch discharge. 4. NOTE: Ring may be...
Instruction Manual - Page 14
... sold in certain states or provinces. CAUTION: Risk of the air compressor. Always use of purchase.
ACCESSORIES
Recommended accessories for use with this tool could be performed by others.
We will repair, without air inlet filter
AIR COMPRESSOR PUMP INTAKE AND EXHAUST VALVES
Once a year have other accessory not recommended for warranty information. English
6. FREE WARNING...
Instruction Manual - Page 15
.... The high pressure at which the motor shuts off , air tank pressure drops when accessory is called cut -in pressure. that bear one or more than its capacity. Cut-Out Pressure: When an air compressor is , the air compressor pump should not run , air pressure in any given hour.
15 The low pressure at which the motor automatically restarts is used...
Instruction Manual - Page 16
......6
Knocking Noise...6
Pressure reading on the regulated pressure gauge drops when an accessory is used 7
Compressor is not supplying ...Pressure switch does not shut off motor when compressor Set the On/Off switch to OFF, if the unit does not shut
reaches cut-out pressure
off contact a DEWALT factory service center or a DEWALT
authorized service center.
2
Pressure switch cut-out too high...
Instruction Manual - Page 17
... It is damaged
14
Motor overload protection switch has tripped
15
Tank pressure exceeds pressure switch cut -in pressure of bursting.
Operate safety valve manually by your air compressor, a larger compressor is used
8
Prolonged excessive use of air usage. NOTE: Adjust the regulated pressure under Features.
Tighten fittings. English Remove, clean or replace. Refer to occur...
Instruction Manual - Page 18
... service center or a DEWALT authorized service center. Do not use a time delay fuse.
3. Check for low voltage conditions and/or proper extension cord.
4. Check wiring connection inside pressure switch and terminal box area. Disconnect the other electrical appliances from circuit or operate the compressor on the pressure switch to the Air Filter paragraph in the paint spray...
Instruction Manual - Page 56
... configuration; A18764 D55168 Copyright © 2006 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the array of pyramids on the surface of lozenge-shaped humps on the handgrip; the "D" shaped air intake grill; and the array of the tool. DEWALT Industrial Tool Co., 701...
Parts Diagram - Page 2
...parts information.
Page 1 All Rights Reserved. Please visit www.dewaltservicenet.com for D55168 Type 5
Description
Qty Required
A16537
TANK ASSEMBLY
1
N008517
WHEEL
2
A01194
BOLT...SCREW #8-32X.375/.34
2
A03857
WASHER
1
N092738
JUMPER
1
ACG-18
CUP SADDLE MOUNT
1
N043321
ROCKER SWITCH
1
CAC-1206-1
CLAMP HOSE .250 ID H
2
D21172
SCREW .250-20X.500 H
4
N015665SV
HANDLE...
Parts Diagram - Page 3
Please visit www.dewaltservicenet.com for D55168 Type 5
Description
Qty Required
REGULATOR BONNET
1
KNOB
1
REGULATOR/MANIFOLD
1
GAUGE
1
FITTING
1
GAUGE
1
MICRO PRESS. SWITCH
1
SAFETY VALVE
1
BRACKET
1
COVER
1
SHROUD REAR
1
FILTER ASSY.
1
FILTER REPLACEMENT
1
DRAIN VALVE
1
GRILL
1
SCREW
1
HOSE
1
HOSE
1
CLAMP
2
LABEL
1
WARNING LABEL
1
LABEL
1
LABEL
1...
Parts Diagram - Page 4
Please visit www.dewaltservicenet.com for D55168 Type 5
Description
Qty Required
PLUG PIPE
2
BODY QC .250 IND .25
1
BRUSH
2
BRUSH SPRING
2
BELT
1
FAN
1
SCREW
1
MOTOR PULLEY
1
FLYWHEEL
1
CONN ROD/PISTON ASSY
1
SCREW
1
...
Similar Questions
Dwe43244n Problems
my grinder shuts off after 3 or 4 seconds. I can unplug and plug it back in but it does the same thi...
my grinder shuts off after 3 or 4 seconds. I can unplug and plug it back in but it does the same thi...
(Posted by rkba1911 5 months ago)
Pressure Switch Wiring
Looking for diagram for D55146 compressor pressure switch
Looking for diagram for D55146 compressor pressure switch
(Posted by Woodlandfarms 1 year ago)
Dewalt D55168 Air Compressor Not Turning On.
I have a DeWalt D55168 air compressor that is not turning on. The circuit was not tripped. The outle...
I have a DeWalt D55168 air compressor that is not turning on. The circuit was not tripped. The outle...
(Posted by rjmsteen 2 years ago)
Part Knob Fits Onto
Looking for a part that the knob screws on to the regulator, not the kit.
Looking for a part that the knob screws on to the regulator, not the kit.
(Posted by suzettetbo 2 years ago)
What Is The Break In Procedure For A Model D55168 Dewalt Air Compressor???
(Posted by chuckspencer3461 2 years ago)