Dell PowerConnect 6248 Support Question
Dell PowerConnect 6248 Support Question
Find answers below for this question about Dell PowerConnect 6248.Need a Dell PowerConnect 6248 manual? We have 5 online manuals for this item!
Question posted by mapyr on April 22nd, 2014
Dell Powerconnect Access Denied! You Are Not Authorized To Enter Into Privilege
mode!
Current Answers
Related Dell PowerConnect 6248 Manual Pages
User's Guide - Page 46
...alternative to access configuration sub-systems. Privileged EXEC mode may occupy any location in the User EXEC mode. This level is reserved for tasks that do not change the switch configuration and ...setting up enable passwords.
46
Using Dell™ OpenManage™ Switch Administrator The Password: prompt now displays.
4. Configure the device and enter the necessary commands to the local ...
User's Guide - Page 47
...been modified during initial configuration.
To return from Privileged EXEC Mode to the User EXEC mode:
console>enable
Enter Password: ******
console#
console#exit
console>
Using Dell™ OpenManage™ Switch Administrator
47
To access and list the Privileged EXEC Mode commands: 1. To list the user EXEC commands, enter a question mark at the command prompt. For example...
User's Guide - Page 72
... port, or through Telnet, at least one user account must have a defined IP address, corresponding management access granted, and a workstation connected to the switch before using CLI commands.
72
Configuring Dell PowerConnect You can be defined. Configure the switch using the autoconfig feature, do not use on the console line only.
1. The Easy Setup Wizard...
User's Guide - Page 81
...and to configure Radius or TACACS+.
• Sets up the switch.
Configuring Dell PowerConnect
81 To save the configuration, enter:
console#copy running-config startup-config
Easy Setup Wizard
An Easy... the switch is setup with only the default factory configuration. The Easy Setup Wizard is given the highest privilege level (level 15).
• Enables CLI login and HTTP/HTTPS access to ...
User's Guide - Page 82
...mode. If there is activated. Functional Flow
The following functional flow diagram illustrates the procedures for this step if SNMP management is discouraged. If it is configured, the default access...permit SNMP access from all IP addresses.
• Sets up the default gateway IP address. Since a switch may be used for the Easy Setup Wizard.
82
Configuring Dell PowerConnect Once ...
User's Guide - Page 84
...Dell PowerConnect Example of prompts and responses associated with running as quickly as possible. The values used is accepted. You may also choose to allow all IP addresses to access...to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration, and gets you enter ...can skip the setup wizard, and enter CLI mode to select management unit)>
Applying Global ...
User's Guide - Page 85
... this account. To setup a user account:
Please enter the user name: admin
Please enter the user password: ********
Please reenter the user password: ********
Step 3:
Configuring Dell PowerConnect
85 The wizard automatically assigns the highest access level [Privilege Level 15] to this setting, and to access the switch. To manage the switch using SNMP (required for SNMP management by default...
User's Guide - Page 86
... (A.B.C.D) or enter "DHCP" (without the quotes) to access the CLI, Web interface, or SNMP interface for using the Dell Easy Setup... address you for the switch. console>
86
Configuring Dell PowerConnect To setup an IP address: Please enter the IP address of...enter the IP subnet mask (A.B.C.D or /nn): 255.255.255.0 Step 4: Finally, set up configuration file. You will now enter CLI mode...
User's Guide - Page 89
... is in a privileged EXEC mode (not in the interface configuration mode. Table 5-1. this case, there is no specific reference to enter the config sub tree. When you first log in, the CLI enters the root of line blocking prevention Flow Control Back Pressure
Default Setting 1G Auto-negotiation Enabled On (Enabled) On Off
Configuring Dell PowerConnect
89
User's Guide - Page 91
...access and configuration rights to the switch from the Boot menu. If a userdefined password is handled through the AAA (Authentication, Authorization, and Accounting) mechanism that manages user access rights, privileges, and management methods. Configuring Dell PowerConnect...time access to the switch. A priority of 15 must be invoked from the local terminal with no password entered. ...
User's Guide - Page 93
...Dell PowerConnect... services require level 15 access and connect directly to appear.
Configuring an Initial HTTPS Password To configure an initial HTTPS password, enter the following commands once ...Web browser enable SSL 2.0 or greater for the page content to the configuration level access. Enter the following commands:
console(config)#ip https authentication local NOTE: You should generate a...
User's Guide - Page 94
...Mode XMODEM
Data Type Code
Destination Filename image2
Management access will be blocked for the duration of the transfer
Are you sure you want to start? (y/n) y
console#boot system image2
Software Download Through TFTP Server This section contains instructions for downloading switch...
switch.
94
Configuring Dell PowerConnect To download an image through a TFTP server.
The switch boots...
User's Guide - Page 95
Enter the command copy tftp://{tftp address}/{file name} image to copy a new system image to start? (y/n) y
Configuring Dell PowerConnect
95
The following is saved in the area allocated for the...Are you sure you want to the switch. The following is an example of the information that appears:
console#copy tftp://10.254.24.64/pc62xxr0v34.stk image
Mode TFTP
Set TFTP Server IP 10.254....
User's Guide - Page 105
... Configuration Process
This section provides the basic steps required to the workstation. 2. should be erased and the switch rebooted.
This section also describes accessing a switch for the first time with the switch. A browser application • One Null Modem F2F cable • Straight or cross UTP (category 5) cable(s)
Initial Connection 1. Configuring Dell PowerConnect
105
User's Guide - Page 111
... that the interface status changed to enter the Privileged EXEC screen mode as shown below: console#
01-Jan-2000 01:43:03 %LINK-I-Up: Vlan 1
01-Jan-2000 01:43:03 %LINK-I-Up: 1/xg1
01-Jan-2000 01:43:34 %STP-I-PORTSTATUS: Port 1/xg1: STP status Forwarding
Configuring Dell PowerConnect
111
This example uses port...
User's Guide - Page 112
... http authentication local
console(config)#ip https authentication local
112
Configuring Dell PowerConnect In this example, the Management station IP is not directly connected to be in STP forwarding mode before pinging the management station. time=0 ms
64 bytes from the switch to Privileged Exec mode: console(config)#ip address dhcp
console(config)#exit 5. a. Enable DHCP...
User's Guide - Page 113
Save the running -config startup-config
Configuring Dell PowerConnect
113 This ensures that the configuration just completed is the same if the switch is 15. console(config)#crypto certificate generate key_generate Generating RSA private key, 1024 bit long modulus console(config)#ip https server 8. console(config)#username Dell password Dell1234 level 15 console(config)#aaa...
User's Guide - Page 114
... connection. 3. In order to configure the switch to allow HTTPS server, and to the switch through the standard Web browser, the SSL (Secure Socket Layer) security protocol is used. The switch Dell OpenManage™ Switch Administrator displays.
114
Configuring Dell PowerConnect Configuring Secure Management Access (HTTPS) When managing the switch securely through HTTPS by a third party...
Release Notes - Page 25
... Mode to the Dell™ PowerConnect™ 6200 Series Systems CLI Reference Guide for 90 seconds. Default: Not applicable
Stacking/CX-4 Module Configuration
Title stack-port / {ethernet | stack}
Description This command is used to acknowledge the banner displayed on that it is a dot1x unaware client. Configurable Message of seconds that the switch waits before authorizing...
Release Notes - Page 27
...switch is reset, the configuration is enabled, then the user may not issue OSPF grace LSAs before the dead interval expires on ports after booting from LAG.
None. User cannot enter Privileged EXEC mode... enters an invalid interface, a generic error message will be prompted to read only access ...fails with large configuration. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Known ...
Similar Questions
You Are Not Authorized To Enter Privileged Mode Dell Powerconnect 6224
(Posted by wifeooceanl 9 years ago)
How To Enter Privileged Mode In Dell 6224 Switch
(Posted by vicchape 10 years ago)
Powerconnect 6248 You Are Not Authorized To Enter Privileged Mode
(Posted by zeb30WClark 10 years ago)
Dell Powerconnect 6248 Ssh You Are Not Authorized To Enter Into Privilege Mode
(Posted by Dragra 10 years ago)
Problem Of Conections On Dell 6248
Hi, good night, I have one switchdell6248and one router configuration forsegment vlans.Whose oncone...
Hi, good night, I have one switchdell6248and one router configuration forsegment vlans.Whose oncone...
(Posted by cjsanntos 11 years ago)