Dell PowerConnect 6224 Support Question
Dell PowerConnect 6224 Support Question
Find answers below for this question about Dell PowerConnect 6224.Need a Dell PowerConnect 6224 manual? We have 5 online manuals for this item!
Question posted by pcrumgsub on November 25th, 2013
How To Backup A Switch Config On A Powerconnect 6224
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerConnect 6224 Manual Pages
Command Line Interface Guide - Page 1322
...SID)
Model Identifier Management Preference Code Version
Description
This field displays the index into the database of the show supported switchtype 1 Switch Type 0x73950001 Model Identifier 6224 Switch Description PowerConnect 6224 Management Preference 1 Expected Code Type 0x100b000 Supported Cards:
Card Index (CID 3 Model Identifier PCM8024 The following table describes the fields in...
Command Line Interface Guide - Page 1339
... affected by the "clear config" command. The priority of one backup switch over another. (Range: 0-12)
Default Configuration The switch priority defaults to the hardware management preference value of the switch to configure the ability of 1. System Management Commands
1339 Examples console(config)#stack
console(config-stack)#standby 2
switch priority
Use the switch priority command in Global...
User's Guide - Page 19
... proceeding, read the release notes for RJ-45 or SFP interfaces. The Dell PowerConnect 6224P adds support for RJ-45 or SFP interfaces. The Dell™ PowerConnect™ 6200 series are provided with hot swappable stack members. The Dell PowerConnect 6224 switch supports 24 1000Base-T copper ports and 4 "combo" ports for power-over-Ethernet (PoE...
User's Guide - Page 59
...10GBase-T module, or a CX4 module. RS-232 management port
DC power
AC power
Figure 4-7. PowerConnect 6224P and 6248P Rear Panel
Dual 10G slots for XFP, CX4, or stacking modules
Dual 10G ...Panel
Each PowerConnect 6200 series switch provides an RS-232 maintenance port, on the rear of the switch.
RS-232 management port
DC power
AC power
Hardware Description
59
PowerConnect 6224, 6248,...
User's Guide - Page 62
... to 576 front panel ports. Power Supplies
The 6200 series switches have one of the short stacking cables into either of the stacking ports of the switch rear. Stacking
You can stack up to 12 PowerConnect 6224 and/or 6248 switches, supporting up to connect the switches. See Figure 4-13.
1. Connect one internal power supply which...
User's Guide - Page 549
... and the management unit in order to forward packets using OSPF routes while a backup switch takes over management unit responsibility.
The restarting router relearns the network topology from the...show ip ospf
Description Displays OSPF route redistribution summary data. In helper mode, a switch continues to advertise to be redistributed by OSPF. • Redistribute -
The OSPF ...
User's Guide - Page 669
...restarts, or both. Helpful neighbors continue to forward packets using OSPFv3 routes while a backup switch takes over management unit responsibility. The operator may initiate a failover in the CLI...8226; OSPFv3 Commands The following table summarizes the equivalent CLI commands for stacked switches. Displaying OSPFv3 Route Redistribution Summary Using CLI Commands
For information about the CLI...
Release Notes - Page 3
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Introduction
This document provides specific information for the Dell PowerConnect 6200 Series switches, firmware version 3.2.0.6. You MUST follow the procedure set forth in the Dell PowerConnect 6200 Series Release 3.2 Upgrade Procedure included in your switch becoming inoperable. It is recommended that the same version of this ...
Release Notes - Page 4
...the functionalities listed, please refer to a backup location before performing this firmware. NOTE: OMNM 4.1 will not discover the switches running firmware version 2.x or earlier.
...
Downgrading from 3.2.0.6 to version 4.2. Hardware Supported
PowerConnect 6224 PowerConnect 6248 PowerConnect 6224F PowerConnect 6224P PowerConnect 6248P
2
System Firmware Version 3.2.0.6 Denotes a ...
Release Notes - Page 5
... fault on the console. Upon changing the role of a module, a reboot of the switch will be configured to either role (Ethernet or Stacking). In order to support this feature,...name. System Firmware Version 3.2.0.6
Page 3 This feature is configurable via an HTTP session. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Added Functionality in this Release ¾ Non-Stop Forwarding
...
Release Notes - Page 7
... DSCP for MLD Proxy and is used to share information between neighboring devices (routers, bridges, access servers, and switches).
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ MLD Snooping (RFC2710)
In IPv4, Layer 2 switches can use IGMP Snooping to limit the flooding of multicast traffic by dynamically configuring Layer 2 interfaces so that rejects...
Release Notes - Page 13
... Restricted TCN - In forwarding state, the link may create a loop in alternate or backup roles. When a port is no longer receives BPDUs, MSTP considers this MIB on previous...Spanning Tree Update - 802.1Q-2005
Spanning Tree now supports IEEE802.1Q-2005. Loop Guard - PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Changed Functionality in this parameter will not flush its MAC address ...
Release Notes - Page 15
...flow control is enabled by default. If your previous configuration had flow control disabled, you upgrade a switch to ip mroute.
snmp-server enable traps is now available from 64 to 256. The ip ... about in a number of the flags for backward compatibility. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ Trap Configuration
In previous versions of the software, configuration ...
Release Notes - Page 19
...reload. Added the no form for syslog description in the respective APIs. The switch must be rebooted for the cutthrough configuration to be deleted for logging syslog.
... cannot be deleted.
Process SET_ASSET_TAG event while in running -config on the DUT. Logging messages show UTC time only.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Issues Resolved
The following ...
Release Notes - Page 21
...groups not visible in upper case letters.
Cannot select the protocol group on the Switching > VLAN > ProtocolGroup web page.
Properly initialized the variable.
Unknown characters being ...no default radius server.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Description Cannot enter Daylight Saving Time from Web interface.
Switch gives error message when entered...
Release Notes - Page 25
.... Dot1X
Title dot1x timeout guest-vlan-period
Description
Use this command in Interface Config Mode to set the number of the command to acknowledge the banner displayed on.... Default: Disabled by default.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
RADIUS Accounting Servers
Title radius-server host acct
Description The switches do not support creating accounting server...
Release Notes - Page 27
...saved config....backups of a LAG. If the configuration is saved and the switch...switch reboots and attempts to 100% packet loss OSPF Dead interval expires on ports after booting from LAG. System Firmware Version 3.2.0.6
Page 25 Issue with large configuration. This is not a problem if VLAN configuration is performed while the port is not a member of their configuration files. PowerConnect 6224...
Release Notes - Page 31
... is used for the interface being configured.
ip default gateway is for the management interface and ip default route is a known limitation of the PowerConnect 6200 series switches.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
LACP
Description LAGs Supported
VLAN
Description vlan association mac command limitations
User Impact Number of LAGs supported:
•...
Release Notes - Page 33
...Version 3.2.0.6
Page 31 The value for all ports shows up as expected
Copies backup image of master to set the value for the msgauth command. Web-based ... The chart displays a count rather than a rate.
agentStpPortRootGuard object
Use agentStpCstPortRootGuard instead.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Management
CLI
Description radius-server mode commands do not ...
Configuration Guide - Page 79
... that this interface the backup. Routing Configuration
79 console(config-if-vlan50)#ip vrrp 20 mode
console(config-if-vlan50)#exit
Using the Web Interface to Configure VRRP Use the following screens to the interface that will recognize. To enable VRRP for VRRP. To configure the interface for the switch • Routing > VRRP > Virtual...
Similar Questions
How To Backup Startup-config Dell Powerconnect 6224
(Posted by Taca 10 years ago)
Cannot Delete Backup Image On Powerconnect 6248
(Posted by lanbfit 10 years ago)