Dell PowerConnect 5424 Support Question
Dell PowerConnect 5424 Support Question
Find answers below for this question about Dell PowerConnect 5424.Need a Dell PowerConnect 5424 manual? We have 3 online manuals for this item!
Question posted by hoskali on December 13th, 2013
What Is The Default Logon For Powerconnect 5424
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerConnect 5424 Manual Pages
Command Line Interface Guide - Page 33
.... Command Groups
The system commands can be accessed from a VT100 terminal connected to the Getting Started Guide and User Guide for configuring the Dell™ PowerConnect™ switch, details the procedures and provides configuration examples.
The CLI is structured, describes the command syntax, and describes the command functionality.
The first time you...
Command Line Interface Guide - Page 294
...the incoming traffic on the
specified interface. • rate-limit - Note: For PowerConnect 5400 devices, the calculated rate includes the 20 bytes of ingress traffic on that ...Interface
Configuration command is not enabled on a port. (Range: 3.5M - 1G )
Default Configuration The default configuration is disabled. Syntax • show qos interface User EXEC mode command displays interface QoS...
Command Line Interface Guide - Page 414
... ACL. • dva - The device supports DVA and ACL.
Default Configuration By default the device supports iscsi. Command Mode Priviledged EXEC mode
414
System Management...
System location:
System MAC Address:
00:00:b0:00:00:00
Sys Object ID:
1.3.6.1.4.1.674.10895.3020
PowerConnect 5400
Type:
Main Power Supply
ok
Status
Redundant Power
ok
Supply Status:
Fan 1 Status:
OK
Fan 2...
User's Guide - Page 4
3 Installing the PowerConnect Device 31
Installation Precautions 31 Site Requirements 32 Unpacking 32
Package Contents 32 ...Pinout Information 36 RJ-45 Connections for 10/100/1000BaseT Ports 36 Port Default Settings 37 Auto-Negotiation 37 MDI/MDIX 38 Flow Control 38 Back Pressure 38 Switching Port Default Settings 38
4 Starting and Configuring the Device 39
Configure the Terminal 40...
User's Guide - Page 13
... this product. When one is connected the other is disabled.
The combo ports are designated as combo port alternatives to the last four Ethernet ports. PowerConnect 5424 Front Panel
Figure 1-2. PowerConnect 5424 and 5428 Back Panel
Introduction
13 Introduction
CAUTION: Before proceeding, read the release notes for installing, configuring and maintaining the...
User's Guide - Page 20
SNMP Version 3 Access to the switch using SNMPv3 provides additional security features that defines current and ...download via TFTP. RMON is defined, each model having it's own security levels. Configuration File Download and Upload PowerConnect device configuration is an extension to specific areas of community entries is a standard MIB that cover message integrity, authentication...
User's Guide - Page 25
...
25 Figure 2-1.
RS-232 console based port The following ports: • 24/48 Copper ports -
RJ-45 ports designated as Gigabit ports • Terminal port - PowerConnect 5424 Front Panel
The front panel contains ports1-24/48, which is used to an RJ-45 port is a single logical port with the following figure...
User's Guide - Page 26
PowerConnect Back Panel Port Description
The device back panel contains connectors for debugging, software download, etc. The default baud rate is designated as illustrated in the Figure 2-2. Figure 2-2. Device Ports
SFP Ports The Small Form Factor Plugable (SFP) port is a hot swappable optical ...
User's Guide - Page 31
... in the System Information Guide included in the
system documentation. Installing the PowerConnect Device
31 To determine the possibility of overloading the supply circuits, add together... the front, sides, and back of all switches installed on the same circuit as explained in the Dell Documentation. Installing the PowerConnect Device
This section contains information about device unpacking,...
User's Guide - Page 37
...port by default is disabled) abilities to the same speed and duplex mode. Installing the PowerConnect Device
...hub) to another. If connecting a NIC that does not support auto-negotiation or is a mechanism established between them. Auto-negotiation is not set to its transmission rate, duplex mode and flow control (the flow control by default.
RJ-45 Pin Number Allocation for switching...
User's Guide - Page 38
...be halted to half duplex mode. By default, this feature is enabled. The receiving side may occupy a link so it becomes unavailable for hubs and switches is disabled. When the MDI/MDIX (... Back Pressure
Default Setting 10/100/1000BaseT copper: auto-negotiation full duplex Enabled No tagging Off (disabled on ingress) Off (disabled on ingress)
38
Installing the PowerConnect Device MDI/...
User's Guide - Page 43
... and password The Setup Wizard guides you through the initial switch configuration, and gets the system up , or if the... device through the device CLI mode. You can be managed (by default,
every port is a member of a VT100 terminal
device. 01-Jan.... If this product.
NOTE: Obtain the following : • The PowerConnect device was never configured before and is used to use the Setup Wizard...
User's Guide - Page 60
... area at the bottom of the feature components.
Led Indicators
Component
Name
Port Indicators
Green
The port is currently active.
The branches in the PowerConnect OpenManage Switch Administrator.
The information buttons provide access to information about the device and access to display the full name of the different device features. For more...
User's Guide - Page 62
...When finished, exit the session with a default password, and can be managed over a telnet session.
62
Using Dell OpenManage Switch Administrator All CLI commands can be virtually ... Enter the device's IP address (as defined in the CLI) in . The Dell PowerConnect OpenManage™ Switch Administrator home page opens.
NOTE: Passwords are both case sensitive and alpha-numeric. 4 ...
User's Guide - Page 280
...2 Select a port in the Port Field. 3 Modify the remaining fields. 4 Click Apply Changes. Used for hubs and switches. • Current MDI/MDIX- MDIX (Media Dependent Interface with Crossover) -
Modifying Port Parameters 1 Open the Port...port of a LAG. • PVE (Uplink)- When two hubs/switches are connected to each other, or two end stations are connected to each other ports within the...
Getting Started Guide - Page 15
... correctly.)
The initial device configuration is through which the device is to be managed (by default,
every external and internal port is a member of a VT100 terminal
device. (Press the... The boot process runs approximately 90 seconds.
Booting the Switch
To boot the switch, perform the following assumptions:
• The PowerConnect device was never configured before, and is in the same...
Getting Started Guide - Page 16
... Configuring the Device Consult the PowerConnect 5400 Series User's Guide for assistance in configuring the device using the setup wizard and configure the switch manually through the initial device ... interactive guidance through the device CLI mode. Would you like to any time by default.
The Setup Wizard configures the following fields. • SNMP Community String and SNMP...
Getting Started Guide - Page 52
...V Uživatelské příručce pro zařízení PowerConnect 5400 Series naleznete pomoc pro konfiguraci zařízení pomocí CLI. Would...switch configuration, and gets you up a SNMP version 2 account, see the user documentation). The system will prompt you accept the default value. By pressing Enter, you with a default answer.
To manage the switch...
Getting Started Guide - Page 106
... by entering {CNTRL+Z]. The system will prompt you accept the default value. Would you like to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration, and gets you prefer. SNMP IP SNMP
IP VLAN 1
VLAN 1 IP
CLI PowerConnect 5400 CLI. You can also skip the setup wizard, and...
Getting Started Guide - Page 124
... Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration, and gets you up and running easily and quickly. The system will prompt you accept the default value.
By pressing Enter, you with a default answer. CLI CLI PowerConnect 5400 SNMP SNMP IP IP IP IP
Welcome to skip the setup...
