Dell PowerConnect 2848 Support Question
Dell PowerConnect 2848 Support Question
Find answers below for this question about Dell PowerConnect 2848.Need a Dell PowerConnect 2848 manual? We have 2 online manuals for this item!
Question posted by clauicab on April 16th, 2014
How To Enable Sflow And Netflow On Dell Powerconnect 2848
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerConnect 2848 Manual Pages
User's Guide - Page 9
... installing, configuring and maintaining the PowerConnect 2808, PowerConnect 2816, PowerConnect 2824, and PowerConnect 2848 Webmanaged Gigabit Ethernet switches. Dell PowerConnect 28xx Systems User Guide
9 These PowerConnect devices are managed by Dell's OpenManage Switch Administrator. PowerConnect 2808
The following figure illustrates the PowerConnect 2816 front panel.
Introduction
This...
User's Guide - Page 10
... ports • 4 SFP combo ports (1000BASE-SX or 1000BASE-LX)
10
Dell PowerConnect 28xx Systems User Guide Figure 1-3. PowerConnect 2848 Front Panel
The PowerConnect 2848 supports the following figure illustrates the PowerConnect 2824 front panel. Figure 1-2. PowerConnect 2824 Front Panel
The PowerConnect 2824 supports the following ports: • 24 Gigabit Ethernet copper ports •...
User's Guide - Page 11
... user may enable or disable this mode, the device operates as a hub with default configuration, and
configuration cannot be changed. • Secure Mode - Dell PowerConnect 28xx Systems...Control or Back Pressure is active on the whole system. PowerConnect Models
Model
PowerConnect 2808 PowerConnect 2816 PowerConnect 2824 PowerConnect 2848
Copper Ports/ RJ-45 Connectors
Optical Ports/ GbE
8 ...
User's Guide - Page 12
...stations is Media-Dependent Interface (MDI) and the standard wiring for hubs and switches is available on 10/100/1000BASE-T Ethernet ports. Flow Control Support ... enabled for server-to take maximum advantage of this facility are frames with Crossover (MDIX). Jumbo frames are detected:
• Cable Type and Status • Cable Length • Fault-Distance
12
Dell PowerConnect ...
User's Guide - Page 13
...Dell PowerConnect 28xx Systems User Guide
13 The MAC addresses are stored in Managed and Secure Modes In Managed or Secure mode, the switch system always performs VLAN-aware bridging. When Multicast groups are statically enabled...
MAC Address Capacity Support The PowerConnect 2808, 2816, 2824 switches support a total of 8K MAC addresses, and the PowerConnect 2848 supports a total of the layer...
User's Guide - Page 14
...enables limiting the amount of Multicast, Broadcast and Unknown Unicast frames accepted and forwarded by the device from work stations configured for Multicast sessions, and which target port receives copies of incoming and outgoing packets from physical link disruption
14
Dell PowerConnect...server authentication. Link Aggregation The PowerConnect 28xx switches support up to four member ...
User's Guide - Page 15
... 30-60 seconds to full-duplex operation.
BootP and DHCP Clients DHCP (Dynamic Host Configuration Protocol) enables additional setup parameters to respond. 30-60 seconds is considered too long of a response time for the switch
Dell PowerConnect 28xx Systems User Guide
15 DHCP service is an on ports. The BootP client then continuously attempts...
User's Guide - Page 16
...Service (CoS) Features
The PowerConnect 28xx system enables users to view the results, using the Web management interface in the system.
16
Dell PowerConnect 28xx Systems User Guide ...queues. Ethernet Switch Management Features
Web-Based Management With a Web-based management interface, the Ethernet Switches' system can be captured across the entire network.
The switches support one of...
User's Guide - Page 20
...Dell PowerConnect 28xx Systems User Guide There are determined by the physical connection used. The system automatically detects the media used at any one time.
On the top right side of a combo port can switch... from the RJ-45 to the SFP (or vice versa) without resetting the device. NOTE: The system can be disabled. PowerConnect 2848 Front Panel
On the front ...
User's Guide - Page 21
... "Management Modes" on the side panel. Dell PowerConnect 28xx Systems User Guide
21
Fans are provided on page 49. Figure 2-8. The following physical dimensions:
• Height - 43.2 mm (1.70 in.) • Width - 440 mm (17.32 in) • Depth - 255 mm (10.04 in .) The PowerConnect 2848 switch has the following figure illustrates the back...
User's Guide - Page 22
...2-2. Diagnostics has failed. Fan LED (2824/2848 only)
On the PowerConnect 2824 and PowerConnect 2848 front panel there is a Managed Mode LED monitoring the switch node as well as indicating diagnostic test results... Green Solid Off
Description The switch is a Power LED. The following figure illustrates the RJ-45 10/100/1000BASE-T LEDs.
22
Dell PowerConnect 28xx Systems User Guide Fan LED...
User's Guide - Page 23
...hold the button for changing between modes, press the button normally. Switch Ventilation Fan
The PowerConnect 2848 switch has three fans and the PowerConnect 2824 switch has one fan for resetting the device. Figure 2-9. The port is.... The port is occurring. Dell PowerConnect 28xx Systems User Guide
23
Green Flashing Activity is currently transmitting in Full Duplex mode. ...
User's Guide - Page 24
...hubs, routers, or other switches are connected through standard RJ-45 connectors to Half Duplex, Full Duplex, and Auto.
1000BASE-T Cable Requirements
All Category 5 UTP cables that are used for 10/100/ 1000BASE-T Ethernet Port
Pin No 1 2 3 4 5
Function TxRx 1+ TxRx 1TxRx 2+ TxRx 2TxRx 3+
24
Dell PowerConnect.../1000BASE-T ports is set to the switch physical interface ports, located on the...
User's Guide - Page 25
...two SFP transceivers combo ports, and the PowerConnect 2848 switch supports four SFP transceivers combo ports for ...control interfaces. AC coupled.
PowerConnect 2824 switch supports SFP diagnostics. Receiver ground (common with transmitter ground) Receiver ground (common with transmitter ground) Receiver ground (common with transmitter ground)
Dell PowerConnect 28xx Systems User Guide
...
User's Guide - Page 33
...Windows XP, and Windows Vista service packs. The console port enables a connection to a terminal desktop system running VT100 terminal emulation ... the console. d Set flow control to 9600 baud. Dell PowerConnect 28xx Systems User Guide
33 b Set the data rate ....com for the terminal. c Set the data format to a switch or server.
2 Make sure each connection is required: •...
User's Guide - Page 35
...Table 3-1. If the cabling is wired to the Rx pair on one transmission device (switch or hub) to another. Both the straight through cables must be connected to Rx, a link...TxRx 1-
3
TxRx 2+
4
TxRx 2-
5
TxRx 3+
6
TxRx 3-
7
TxRx 4+
8
TxRx 4- Table 3-2. Dell PowerConnect 28xx Systems User Guide
35 RJ-45 Connections for the twisted-pair ports, Tx pair on one cable end must be used...
User's Guide - Page 36
... for switching ports. Back Pressure
The device supports back pressure for additional traffic.
36
Dell PowerConnect 28xx Systems User Guide It can be enabled per ...hubs and switches is known as MDIX.)
Flow Control
The device supports 802.3x Flow Control for ports configured with a device 10/100/1000BaseT port that is a mechanism established between two link partners to enable...
User's Guide - Page 37
... state Port tagging Flow Control Back Pressure MDIX (not user-configurable)
Default Setting 10/100/1000BaseT copper: auto-negotiation full duplex Enabled No tagging On Off (disabled on ingress) On (relevant to coppers ports only)
Dell PowerConnect 28xx Systems User Guide
37
Switching Port Default Settings
The following table gives the port default settings.
User's Guide - Page 55
... can be determined by viewing the actual device. Using the Switch Administrator Buttons
This section describes the buttons found on -line support and online help containing information to the page currently open.
Dell PowerConnect 28xx Systems User Guide
55 Blue
The port is currently enabled. For example, if the IP Addressing page is open...
Getting Started Guide - Page 7
... • PowerConnect 2824 • PowerConnect 2848 The PowerConnect 2800 series can be mounted in and start using it. The PowerConnect management features are ideal for the latest documentations and software updates. The switch is necessary. Site Preparation
Site Requirements
The PowerConnect 2808/16/24/48 devices can be used to Managed, as described in the Dell™ PowerConnect™...
Similar Questions
How To Setup User Login For Enable Command On Powerconnect?
(Posted by cnifrien 9 years ago)
Does Dell Make An Sfp Module For The Powerconnect 2848 For 10g For Singlemode?
Does Dell make an SFP module for the PowerConnect 2848 for 10G for SingleMode fiber? Want to connect...
Does Dell make an SFP module for the PowerConnect 2848 for 10G for SingleMode fiber? Want to connect...
(Posted by jimmurray39132 11 years ago)