D-Link DMC-300SC Support Question
D-Link DMC-300SC Support Question
Find answers below for this question about D-Link DMC-300SC - Media Converter - External.Need a D-Link DMC-300SC manual? We have 1 online manual for this item!
Question posted by lesskosgei on April 16th, 2010
Dmc-300sc Converter Not Working
i have a DMC-300sc media converter which when i connect them back to back with a single mode fiber cord they don't communicate. I have also used a multimode cable connecting to a cisco catalyst 2950 gigabitethernet port and the port on the switch is not showing any LEDs. any one who might have experienced the same problem ? and probably a solution.
Current Answers
Answer #1: Posted by popns on June 22nd, 2010 11:52 AM
popns
Member since:
June 19th, 2010 Points: 3,310
Member since:
June 19th, 2010 Points: 3,310
Find details on the link http://www.dlink.com/products/?pid=596
You can se that DMC-300sc is 100BaseFX/TX multimode media converter. It means that you can not use singlemode fiber cable for connection. This is because emitting diode can not insert enough light into the fiber that has 9 microns core. Try with multimode cable with 50 or 62,5 microns core.
Regarding connection with gigabit Cisco, you can not connect it because DMC is 100BaseFX and Cisco has port that is 1000BaseFX so thay can not communicate with each other. You should use 100BaseFX multimode, plug in GBIC for Cisco.
Related D-Link DMC-300SC Manual Pages
User Guide - Page 1
10/100BASE-TX to 100BASE-FX
Media Converter User's Guide
Rev. 01 (JUN. 2002) 1907M110MM16003
RECYCLABLE
User Guide - Page 2
TABLE OF CONTENTS TABLE OF CONTENTS ... 2 INTRODUCTION 3
ABOUT MEDIA CONVERTER 3 PRODUCT FEATURES 3
INSTALLATION 4
SELECTING A SITE FOR THE EQUIPMENT 4 CONNECTING TO POWER 5 SLIDING SWITCH 5 CONNECTING TO POWER 6 INSTALLING IN A CHASSIS 6 LED INDICATOR 7
SPECIFICATIONS 8
RECYCLABLE Rev. 01 (Jan. 2002)
6012-9600128 1907M110MM16001
Printed In Taiwan
2
User Guide - Page 3
...-pressure & IEEE802.3x compliant flow control Full wire-speed forwarding rate Front panel status LEDs Used as a stand-alone device or with a chassis Hot-swappable when used with a chassis
3 single-mode fiber using SC, LC or MT-RJ connector;
About Media Converter
The Media Converter is a network technology specified by IEEE 802.3 10BASE-T, IEEE802.3u 100BASE-TX, 100BASE-FX standards...
User Guide - Page 4
... of the equipment. 5. Selecting a Site for the Equipment As with any electric device, you select should not exceed the electromagnetic field (RFC) standards for the Converter. The ambient temperature should place the equipment where it will not be between 32
and 104 degrees Fahrenheit (0 to extreme temperatures, humidity, or electromagnetic interference...
User Guide - Page 5
... the converter, and then attach the plug into a standard AC outlet with a voltage range from 100 to Power
1. Half Duplex
Full Duplex (default)
5 Connecting to 260 Vac. Sliding Switch There is a plug-and-play device. 2. This Converter is a sliding switch for duplex mode setting for more details. Refer to the table below for fiber port...
User Guide - Page 6
Step 3- Connecting to secure it.
6 Connect the supplied AC to DC power adaptor
with the chassis: Step 1- Plug in a Chassis
The Converter can be fit into a standard AC outlet. First, install the converter onto a carrier supplied with a power voltage of 7.5Vdc/1.5Amp to any of the vacant
slot. Unscrew and pull out the media converter
board. Step...
User Guide - Page 7
LED Indicator
The LED indicators give you instant feedback on status of the converter:
LEDs Power (PWR) 100 Mbps (100)
TX Port (TX) FX Port ... at 100Mbps on TX port Runs at 10Mbps on TX port Connection in full duplex mode FDX stands for FULL-DUPLEX Connection in half duplex mode Data collision
A valid network connection established
Not Linking Transmitting or receiving data ACT stands for Activity...
User Guide - Page 8
... ft) 100BASE-TX -2-pair UTP Cat. 5, up to 100 m (328 ft) 100BASE-FX -62.5/125um multi-mode fiber optic cable, up to 2 km 10/125um single-mode fiber optic cable, up to 75 km L120 × W88 × H25 mm 305 g External power adaptor 7.5V 1.5A 7.2W Max. Operating:0°C ~ 40°C (32°F ~ 104°F) Storage: -25...
Similar Questions
Default Ip To Login To Switch Des-1018mp?? Isn't This The 10.90.90.90 Ip Addres
Hi.Default IP to login to Switch DES-1018MP??Isn't this the 10.90.90.90 ip Address??
Hi.Default IP to login to Switch DES-1018MP??Isn't this the 10.90.90.90 ip Address??
(Posted by hrgolmoradi 1 year ago)
When I Power On Switch,all Led's Over Ethernet Ports Starts Glowing Continously
when I power ON Dlink DGS-3426 24 ports switch,all LED's over ethernet ports starts glowing continou...
when I power ON Dlink DGS-3426 24 ports switch,all LED's over ethernet ports starts glowing continou...
(Posted by riferakesh 2 years ago)
How To Connect Cisco Network Switch To D-link Des 1024d For Lan Connection
(Posted by srinivasdvm 11 years ago)
Dwl 3200 Ap
Hi I have a problem with my 2 dlink DWL 3200 Ap when conected to a switch they run smoothly for abo...
Hi I have a problem with my 2 dlink DWL 3200 Ap when conected to a switch they run smoothly for abo...
(Posted by beyond032002 11 years ago)
D-link 310gt Not Working With The Catalyst Cisco6509 Multilayer Switch
i am connecting this module with cisco 6509 multilayer switch.What it is not working.when i am check...
i am connecting this module with cisco 6509 multilayer switch.What it is not working.when i am check...
(Posted by rajnishkatoch123 11 years ago)