D-Link DKVM-8E Support Question
D-Link DKVM-8E Support Question
Find answers below for this question about D-Link DKVM-8E.Need a D-Link DKVM-8E manual? We have 1 online manual for this item!
Question posted by waseemakhtar759 on October 26th, 2019
Forget Password Any Easy Solution For Sovlve Password
Forget Password Any Easy Solution For Sovlve Password
Current Answers
Answer #1: Posted by waelsaidani1 on November 18th, 2019 10:55 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
Resetting your D-Link® router's Wi-Fi password is easy:
- Type your router's IP address -192.168.0.1- into your Web browser.
- At the login screen, select "Admin" from the drop down menu and enter your admin password.
- Once you access the Web configuration screen, click "Setup" in the top menu.
- Select the "Wireless Settings" link on the left-hand side.
- From there, click on the "Manual Wireless Connection Setup" button.
- Scroll down to the field representing my "Pre-Shared Key". If you don't see it, select a security mode from the dropdown menu at the bottom of the screen first.
- Type in a new password. (I use a hybrid WPA/WPA2 security mode.)
Related D-Link DKVM-8E Manual Pages
Product Manual - Page 1
DKVM-8E
8- Port Keyboard, Video, and Mouse Switch
User's Guide
Rev. 1.0
Product Manual - Page 3
... banks of DKVM-8E units
n Hot plug-Add PCs or remove connected PCs for naming each channel contains a microprocessor emulation to name and select computers
n Supports eight characters password protection and ... and monitor
n No software required, each PCs and selecting one of them.
Introduction
The DKVM-8E gives you the ultimate in control of 8 PCs from one keyboard, mouse and monitor. ...
Product Manual - Page 4
... n Recalls CAPS LOCK, NUM LOCK and SCROLL
LOCK keys' status for each computer automatically n Supports VGA, SVGA and MultiSync monitors n Supports up to install your DKVM-8E, please make sure that have serial mouse ports while using a PS/2 mouse only at console n Keyboard and mouse emulation for error-free boot ups n Microsoft...
Product Manual - Page 5
Item DKVM-8E Power Adapter
Qty 1 pcs. 1 pcs.
3 in -one Cable Kit to PC DB-9 to 6-pin Mini-DIN This manual
- 3 -
Remark Keyboard, mouse & monitor switch DC12V,1A 1 set : 3 feet 3-in-one Cable Kit to daisy chain 2 sets : 6 feet 3-in 1 KVM cable kit 3 sets
Mouse Adapter cable User's Manual Rack mount bracket Screw Rubber foot
4 pcs 1 pcs. 2 pcs. 8 pcs. 4 pcs.
Product Manual - Page 6
Front Panel Layout
Current Active Bank Display Current Active Port Display
Bank Select
Port Select
Power Switch
- 4 -
First the layout of front and rear panel will explain how to connect the console and the computers to the DKVM-4 switch unit. Hardware Installation
This section will be shown.
Product Manual - Page 7
Before attempting to connect anything to your computers and the DKVM-8E. Real Panel Layout
Console Port Connectors
Daisy Chain Port
PC Port Connectors
VGA monitor PS/2 ... order as shown, otherwise, keyboard and/or mouse errors may cause irreversible damage to the DKVM-8E or the computers, make sure everything is powered off .
Otherwise, plugging and unplugging cables may occur.
- 5 -
Product Manual - Page 8
... to
the sides of your
cables so that your monitor, connect it ideal mountable on the back of the KVM-08 labeled with your computers, DKVM-8E, keyboard,
mouse
and
monitor
are
distanced
properly. Using the attached cable, or the one included with the monitor symbol at the CONSOLE connector...
Product Manual - Page 9
Step 4 Connect the mouse to the DKVM-8E. Step 3 Connect the keyboard to the DKVM-8E. If you have an AT type keyboard, you will need an AT to PS/2 adapter.
Step 5
- 7 -
Product Manual - Page 10
...the PC connections will be made with the Male side to both of the PC and the rear panel of the DKVM-8E unit to the connector labeled VGA. Connect a VGA cable (15-pin HDDB Male / Male) with the monitor ...computer's mouse cable to the PC1 PS/2 mouse port on the computer, and the other end to the DKVM-8E. If using a serial mouse cable, connect one end to the PS/2 mouse port on the computer, and...
Product Manual - Page 11
... port on the computer, and the other end into an electrical receptacle. Back of PC Step 8 Double-check all of DKVM-8E. Make sure the keyboard and mouse cables go to the DKVM-8E. Now you will see the LED for the remainder of the computers. Using another PS/2 cable connect one end to...
Product Manual - Page 12
...10 - If you switch PC ports on the KVM at this moment, it may check to the stand alone switch, DKVM-8E still needs a power adapter for proper connections before going to the trouble shooting section of this is OK, use the... after the system has booted up process. Although the PCs connected to DKVM-8E are under their boot-up . You may cause the unpredictable behavior or shut down the PC.
Product Manual - Page 13
...-set. keep the default eight zero (00000000) value. Usage
The power on state of DKVM-8E
When you are not familiar with the operation of OSD manual, please don't change the password -
Otherwise, if you have set the password and unfortunately forget the password, you will ask for the password, the default password value is eight zero -" 00000000 ". i.e.
Product Manual - Page 14
... PC ports. With reset command, the PC ports of master DKVM-8E to assign a new ID to initial state --- Only power off DKVM-8E can reset KVM switch. When you add a new DKVM-8E as a slave bank, please use reset button of DKVM-8E will flash. Check the password, but also re-check all of eight PCs ports and...
Product Manual - Page 16
... using the numeric keys on the keypad are not available as a hot key command.
and port no . If you set up scan mode command already, DKVM-8E issue one beeper for confirmation every time when one of Auto Scan Mode, press any key or SPACE bar. Scroll Lock +
Scroll Lock +
=BBeeper
Note...
Product Manual - Page 17
... other end for the console port (white color block) of bank 1 KVM switch.
2. Connect Keyboard, Mouse and Monitor to daisy chain DKVM-8E. Rom re-flash command need take 1~2 minutes. 2.Not including password
Scroll Lock +
Scroll Lock +
=FSearch the same PC name
F I N D : ¦
Note: Search PC name starting from 1st PC port
Scroll...
Product Manual - Page 18
... daisy chain the KVM Switches.
. :
MASTER (Bank 1) SLAVE (Bank 2) SLAVE (Bank 3)
SLAVE (Bank 8)
Bank:1 Bank:2 Bank:3 Bank:8 Maximum 8 Levels
Hot Plug
The DKVM-8E supports "Hot Plug" function for easy addition or removal of PCs. Please use the attached 3 feet 3-in-one Cable Kit to daisy chain more bank as follows:
1. 3. A PC can...
Product Manual - Page 20
...
04
0 ¤ SYSTEM 05 0 SYSTEM 06
0 SYSTEM 07 0 ¤ SYSTEM 08
xOSD: 10 SEC. You will see the following small window on your monitor. zCHANGE PASSWORD
ySCAN:10 SEC.{CONSOLE ON/OFF
|ESC: QUIT
ENTER:
TAB: NEXT
INSERT: EDIT
Ç/È: SELECT PORT
PgDn / PgUp: BANK SELECT
u The 1ST line bar...
Product Manual - Page 21
...is 10 sec and the maximum scan time is eight digits. z "CHANGE PASSWORD" allows the user to change the
password used to 99 sec. The maximum password is 99 sec.
w The sun symbol "¤ " beside the PC...modify it from 05 sec to access all PC systems connected. y "SCAN TIME" is powered on your typed password.
- 19 - After you select this item and then press the Enter. x The "OSD: 10 SEC" ...
Product Manual - Page 22
...When you select "CONSOLE OFF"(factory default is OFF state), a password must be entered to retype the password again for password authentication. If you reset the KVM switch, or there is matched...NEW PASSWORD COMPLETE
ESC: QUIT
ENTER : COMPLETE
{ "CONSOLE ON/OFF" lets you finish using the KVM switch, please do not forget to set to OFF for rechecking your
previous key-in password is...
Product Manual - Page 23
When editing is finished, press the "Enter" key to select items like Bank, OSD, SCAN, CHANGE PASSWORD, CONSOLE ON/OFF, etc... When you finish the set up of PC name and get out of monitor.
After you have selected the PC port ...
Similar Questions
How Can I Reset My Password For Dlink 815 If I Forget My Password
(Posted by AmySklhuf 9 years ago)
Re-set Password For Dkvm-8e
Hello,plase send reset password of DKVM-8E switch to
Hello,plase send reset password of DKVM-8E switch to
(Posted by mahmoud485 11 years ago)
How Do You Reset The Password On A Dkvm-8e
how do you reset the password on a DKVM-8E
how do you reset the password on a DKVM-8E
(Posted by Anonymous-47962 12 years ago)
Need To Turn Console On For Dkvm-8e 8-port Kvm Switch
Need to turn concole on for DKVM-8E 8-port KVM switch
Need to turn concole on for DKVM-8E 8-port KVM switch
(Posted by pcknight 12 years ago)
Problems With Password For Camera In Setup Wizard.
I tryed to install the Dlink dcs 932L camera. Conneting it to my network went well. The wizard shows...
I tryed to install the Dlink dcs 932L camera. Conneting it to my network went well. The wizard shows...
(Posted by ccvrouwe 12 years ago)