Cub Cadet FT 24 Support Question
Find answers below for this question about Cub Cadet FT 24.Need a Cub Cadet FT 24 manual? We have 2 online manuals for this item!
Question posted by rodgermc on April 13th, 2014
Where Does Spring Of Forward Tine Engagement Cable Attach?
The person who posted this question about this Cub Cadet product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Cub Cadet FT 24 Manual Pages
Operation Manual - Page 1
...) Printed In USA
CUB CADET LLC, P.O. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Front Tine Tiller - Model FT24
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
Operation Manual - Page 4
...Be careful when tilling in the ground and propel the tiller forward. After striking a foreign object, stop the engine and make certain the tines and all times.
11. Repair any damage before starting ...in this is hot or running .
20. i. Do not touch.
15. Use only attachments and accessories approved by attempting to the instructions found in place and operating properly.
19. ...
Operation Manual - Page 7
... Gage Assembly
Assembly
2.
Hook the "Z" end of the forward clutch cable (A) into the reverse tine engagement lever Fig. 3-2.
7 Assembly & Set-Up
3
Contents of tiller are determined from
behind the equipment in the operating position.
Hook the "Z" end of the reverse clutch cable (B) into the forward tine engagement lever Fig. 3-2.
References to kink cables while attaching.
Operation Manual - Page 10
...Use maximum engine speed when tilling.
Controls and Features
4
Reverse Tine Engagement Lever
Handle
Throttle Control
Forward Tine Engagement Lever Handle Knob
Depth Stake
Tiller Tines
End Cap
Engine Controls
Figure 4-1
Tines and End Caps
See the separate Engine Operator's Manual for seeding. Forward Tine Engagement Lever
The forward tine control lever is located on top of the upper...
Operation Manual - Page 11
Operation
5
Starting the Engine
WARNING!
Attach the spark plug wire to prevent accidentally starting cold a engine.
5. Make sure that the tine clutch control is standing in front ... plug wire and ground it is unattended. Setting the Depth
Yoke Forward
Place the wheel yoke so that wheels are forward (nearest to tines) for deep tilling and cultivating. closest to Back
Place the wheel...
Operation Manual - Page 13
... of hard untilled spots, allowing a better stand of the garden and then by removing the outer tines completely from the tiller. The tine width can be done by working depth. Figure 5-5
Other ...instructions on removing the tines. Your tiller may be reduced to the full working the length of grass to permit cultivation between the rows. Operation
13 One of lawn area for mixing it...
Operation Manual - Page 14
... case and cause serious damage to the Separate Engine Operator's Manual packed with light oil. Tine Shafts
Remove the tine assemblies and lubricate the tine shafts at least once a season with your tiller. See Fig. 6-1.
Reverse Tine Engagement
Cable
Forward Tine Engagement
Cable
Figure 6-1
1. Hex Nut
Figure 6-2 14 Maintenance
Engine
Refer to clean your tiller. Adjust either the...
Operation Manual - Page 15
...
15 3.
Check again for correct tension on the cable.
If the tines turn toward rear, adjust the reverse tine engagement cable to increase or End Caps
decrease tension on cables. Retighten the lock nut against the cable collar. The tines should not turn forward, adjust the forward tine engagement cable to prevent tilled soil from overflowing
onto unwanted areas...
Operation Manual - Page 16
NOTE: When storing any springs, bearings, and cables.
16
Section 6- Lubricate the tiller as fertilizer. Do not store next to prevent rust.
5. Wipe tines with oiled rag to corrosive materials, such as described in a clean, dry area. Off-Season Storage
If the tiller will result in shortened life and ...
Operation Manual - Page 18
... idler pulley and then
from the engine and transmission pulleys. To reassemble the new belt, follow the instructions in Fig. 7-4.
Return Spring
Screws
Figure 7-3
3.
Service
Engine Pulley
Figure 7-6 6. Forward Drive Belt
4. Remove the return spring.
See Fig. 7-6. the engine pulley. Take note of the notch on the bottom of the engine pulley. The...
Operation Manual - Page 19
...cable not adjusted properly 4. Belt worn and/or stretched
Remedy
1. Clean fuel line 4. Clean, adjust gap or replace 8. Refer to ON position 6. Adjust carburetor as instructed in tines 2. Forward... overheats Tines do not engage
Tines skip over ground Wheels do not engage
Cause
1. Drain fuel tank, refill with proper oil 2. Fill crankcase with fresh fuel 6. Replace tine clevis ...
Operation Manual - Page 20
... and Description
642-0002 642-0003
Inner Right Hand Tine Inner Leftt Hand Tine
642-0023 642-0024
Outer Left Hand Tine Outer Right HandTine
714-0149B 711-0415
Cotter Pin Clevis Pin
754-0428 754-0429
Forward V-Belt, Reverse V-Belt
746-0918 749-0953
Forward Cable Reverse Cable
734-1268
Wheels, 8" x 1.75"
98079-56846 Spark Plug...
Operation Manual - Page 24
...from the installation or use of any part, accessory or attachment not approved by Cub Cadet for whom it was purchased... without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to applicable manufacturer...(excluding its Normal Wear Parts as : batteries, belts, blades, tines, wheels and tires. CUB CADET LLC MANUFACTURER'S LIMITED WARRANTY FOR
...
Parts Manual - Page 7
...Tine Assembly, LH, Outer Tine Assembly, RH Inner Tine Assembly, Left Inner Tine Assembly, Right Forward Clutch Cable Reverse Clutch Cable Flat Pulley, 6"
Ref. Model Series 390
Ref. Part Number 23. 950-0892 24... Washer, 525" x 1.5" Hex Jam Nut, 1⁄2-20 Return Spring Reverse Bracket Lock Washer, 5⁄16 Hex Bolt, 5⁄16-24 x .625" Engine Inner Pulley Reverse Engine Pulley Bell Washer, ....
Parts Manual - Page 9
... Lock Tine Shield Bracket, Tine Shield Idler Bracket Assembly Hex Head Screw, 5/16-18 x 3.00 Hex Head Screw, 5/16-24 x .625 Hex Head Screw, 3/8-24 x 1.00
Ref. Part Number 23. 710-3005 24. 711...340 x .872 x .060 Flat Washer, 1.26 x 1.87 x .150 Bell Washer, .396 x 1.140 x .095 Forward Clutch Cable Pulley Adaptor Spacer, .64 ID x 2.4 Belt, 4L x 41.9 LG Pulley 1.88 OD Pulley 6.00 OD Inner Engine Pulley...
Parts Manual - Page 11
...786-04092 22. 786-04104 23. 786-04352A 24. 786-04355A 25. 786-04356 26. 786-...Spring Shoulder Screw, .405 x .435 5⁄16-18 Shoulder Screw, .498 x 1.635 Stop Screw Tiller Flap Rod Spacer Side Shield Rear Tine Shield Reverse Stop Arm Drag Bar Tine Shield Mounting Bracket Tine... Plug End Bell Washer, .340 x .872 x .060 Reverse Cable Forward Cable Clutch Bail Spacer, .322 x .625 x 2.00 Handle Crank ...
Parts Manual - Page 13
... Spacer V-Belt, 4L x 25.375 Long V-Belt, 3L x 29.125 Long Engine Pulley Transmission Pulley Cable Roller Idler Bracket, Forward Cover Plate Idler Bracket, Reverse Mounting Frame, RH Mounting Frame, LH Pulley Bracket Pulley Shield Tine Assembly, LH Tine Assembly, RH Clevis Pin, .375 x 1.75
13 Part Number 1. 634-04736
634-04735 734-04163A...
Parts Manual - Page 17
...Clevis Pin Hex Nut, 3⁄8-24 13" Articulating Tine Shoulder Bolt Bell Washer, .515" ID x 1.14" OD Shoulder Bolt Tine Adapter Assembly, 18" Internal Cotter Pin Lock Washer Tine Adapter Plate Cap Washer, Flat... Nut, 1/4-20 Flangelock Nut, 3/8-24 Hexlock Nut, 5/16-18 Stud, 5/16-18 x .75 Small Tee Knob Foam Grip, .970 x 11.0 Grip, .1875 x 1.00 Battery Clamp, 5/16 Cable Tie, 8.5 LG End Plug Washer...
Parts Manual - Page 19
... Hex Head Screw, 1/2-13 x 5.50
† If Equipped
19 Part Number 22. 756-0971 23. 756-0972 24. 756-1162 25. 786-0064A 26. 786-0185A 27. 786-0187 28. 786-0193 29. 934-04365A 30. 936... 1/2 Flat Washer, .25 ID x .93 OD Spring Washer, .317 ID x .625 OD Hub, .636 ID x 1.00 OD x .94 Bell Washer, .396 ID x 1.14 OD Shoulder Nut, 7⁄16-20 Clutch Cable Idler Pulley Rod V-Belt Flat Idler w/ Flange, 3....
Parts Manual - Page 21
...-0570 - 986-04074B
Description Gear Spur, 16T Shaft Seal, 1.0 Shaft Seal, .75 Positioner Gear Bracket Tapered Cap Plug Compression Spring, .230 OD Washer, Flat, 1.03 x 1.62 x .03 Washer, Lock, 7/16 Washer, Flat,.474 x .879 ... 21. 717-0853A 22. 717-1582A 23. 717-1583 24. 717-1584 25. 717-1585 26. 717-1587
Description Shaft Assembly, Tine, 18T Shaft Assembly, Jack Shaft Assembly, Shift Input Shaft ...
Similar Questions
The Tines On The Tiller Seem To Be Frozen And Will Not Engage Or Turn
(Posted by Woodlandchimney5 1 year ago)
Engaging Forward Drive
how can I engage forward or reverse drive without engaging the times on the VT100
how can I engage forward or reverse drive without engaging the times on the VT100
(Posted by Whlaney 8 years ago)
The Shifter Was Very Hard To Shift And Would Not Go To Front Tine Forward. When
(Posted by beverlinwb 11 years ago)