Craftsman 21805 Support Question
Craftsman 21805 Support Question
Find answers below for this question about Craftsman 21805 - 10 in. Table Saw.Need a Craftsman 21805 manual? We have 1 online manual for this item!
Question posted by dianeb252 on December 22nd, 2011
Drives
does this table saw have either belt dxriver or direct driver?
Current Answers
Related Craftsman 21805 Manual Pages
Operation Manual - Page 1
OPERATOR'S MANUAL
10 in. TABLE SAW Model No. 315.21 8050
_lJ WARNING: To reduce the risk of injury, the user must reed end understand the operator's manual before using this ...
Operation Manual - Page 4
...10 in ripping or crosscutting. Stay out of the motor could ignite fumes. • INSPECT TOOL CORDS PERIODICALLY. Through- Do not operate tool...support ]argo panels.
• REMOVE ALL FENCES AND AUXILIARY TABLES before cutting,
• NEVER TOUCH BLADE or other moving .... saw blade. If tool is equipped with or without yellow stripes is moving parts during
use.
• NEVER START A TOOL ...
Operation Manual - Page 5
... your hand to move into the cutting tool,
• USE ONLY RECOMMENDED ACCESSORIES listed in line with the path of accessories that no obstructions will
interfere with safe operation BEFORE performing any work using the table saw.
• ALWAYS TURN OFF SAW before it is attached to the saw.
• AVOID KICKBACKS (work with the...
Operation Manual - Page 9
...Resaw A cutting operation to reduce the thickness of the workpiece to the table surface. Riving Knife/Spreader/Splitter (table saws) A metal piece= slightly thinner than 90%
Non-Through Cuts Any ...strokes per minute), used to blade movement,
Freehand Performing a cut which abtade or cutting tool is being done, Worktable Surface where the warkpieee rests while performing a cutting, drilling, ...
Operation Manual - Page 11
...belt drive, is raised and lowered with, the height/bevel adjusting handwheeL Bevel angles are locked with the bevel locking lever.
,_ WARNING: Do not use this tool... saw is secured with a 36-tooth, 10 in which helps keep the blade guard down over the saw table ...angle for bevel angles easy. This saw table.
The easy-to use the tool.
11 MOTOR - This table extension at 90 ° and...
Operation Manual - Page 12
... switch button to start the tool.
TO TURN YOUR SAW OFF:
• Press the switch button down .
• Remove the switch key from accidentally starting ,
Always make sure your workplace is
not in use by an insert called the throat plate.
miter cuts, bevel cuts. POWER SWITCH
This saw table has rails on the...
Operation Manual - Page 14
...Blade Wrench 2
O. Rip Fence 1 D. Extension Table (right 1
K. Indicator (left 1
J. Screw (M4 x 10 ram 2
G. Dust Bag 1
N, End Plug (left
1
F. Hex Key 1
Ft Screw (M4 x 25 mm 2
H. Spider Leg Stand 1
I. Miter Gauge 1 C. The following items are included with Spreader and Anti-Kickback Pawls 1
B. Blade Guard with your table saw:
It E
M P
L
Fig. 1
A. Bevel...
Operation Manual - Page 15
... with this tool or create accessories not recommended for accuracy.
not your back, and get help .
Fig, 7
WARNING: Never stand directly in line with your legs, net your knees bent and lift with the blade or allow hands to a workbench or an approved leg stand. Failure to make sure the table saw is factory...
Operation Manual - Page 16
...Place the nylon nut into the slot and turn the locking knob clockwise to secure the table saw base on the end of the height/bevel adjusting handwheel and hold in the top of...HEIGHT/BEVEL ADJUSTINGHANDWHEEL
HEXNUT
BEVEL HANDLE
SCREW
WASHER
._;DCAP F_.10
Fig. 9
MOUNTING HOLES
The table saw must be of sufficient length to accommodate the saw base, lock washers, hax nuts, and the thickness of...
Operation Manual - Page 20
... in line with push st[cks. Never stand directly in electric shock. Use it will not fit the...tool for safely pushing a workplace through cuts. Refer to use the rip fence when rip cutting and the miter gauge when cross cutting. This helps prevent twisting the wood in one end and shaping for knots or nails before beginning a cut.
• When making and woodworking NOTE=This table saw...
Operation Manual - Page 22
... in . Feed the stock only to the mark previously made at 6 in., 8 in., 10 in . Completely lower the saw table.
_k WARNING: DO not locate the featherboard to completely stop rotating before removing the stock.
I... performed and lock the rip fence, Place the workpiece against the table or fence. Turn the saw blade area, Adjust the featherboard to apply resistance to the workpiece just forward of...
Operation Manual - Page 27
Failure to heed this tool. NOTE."To prevent unauthorized use, remove the switch key as shown in figure 34. • Let the blade ...make e test cut operations.
_ WARNING;
MAKING A CROSS CUT
See Figures 33 - 34.
_1, WARNING: Using the rip fence as saw table) behLnd the saw for the cut work,
• Make sure the wood is clear of the blade before turning on scrap wood first. Do not use ....
Operation Manual - Page 33
.... THROAT PLATE
BLADE GUARD
'READER
REXWRENCH
Fig. 44 33
BLADE
/
Fig. 46 Raise the saw blade, raise the blade guard, and remove the throat plate_
• Make sure the bevel ... accessory blade, follow the instructions provided with a flaming square and make sure the tool is securely tightened. The table saw to make sure it turns freely.
• Lower the sew blade and reinstall ...
Operation Manual - Page 36
...use any aerosol or petroleum solvents,
LUBRICATION
This saw dust from slipping during power tool operation or when blowing dust. A A WARNING...; Periodically check all clampS, nuts, bolts, screws, and belts for tightness and condition.
Use of the miter gauge. &#... from underneath the table and in position.
• Check the blade guard assembly. • TOmaintain the table surfaces, fence,...
Operation Manual - Page 39
CRAFTSMAN 10 in damage to the drive system possibly causing electrical shock or electrocution, Any repairs requiring disassembly of your tool require safety testing aad should only be performed by a Sears Service Center. TABLE SAW - k MODEL NUMBER 315.218050
36 45
co
I
34 C B
D
2O
SEE_OTE"A"
_IL WARNING: Lmproperelectrical repair of the table saw can resu]t in .
Operation Manual - Page 40
... to be found on the data plate attached 1o the cabinet.
May Be Purchased Locally
=
NOTE: =A" - TABLE SAW - The assembly shown represents an important part of a double insulated product can result in 2
Screw, Pan Hd. (M4 × 10 ram 2
*Standard Hardwere Item - i
_WARNING: Improper repair of the double insulatedsystem. Any repairS requ r ng...
Operation Manual - Page 41
•
CRAFTSMAN 10 in damage to the dnve system possibly causing electrical shock or electrocution. Any repairs requiringdisassembly of the table saw can result in . TABLE SAW - MODEL NO. 315.218050
21
53
56
22
23 24
8
4 2
46" [J
42
43
51
31
36
\
54
-37
G
,_L WARNING. Improper electrical repair of your ...
Operation Manual - Page 42
...May Be Purchased Locally
42 MODEL NO. 315.218050
.... TABLE SAW - PART NUMBER
DESCRIPTION
QTY.
0121010919 0134010224 410138743
0121O10906 ...Screw (M4 x 16 ram 2 Power Cord Clamp 2
" Self Tapping Screw (8-16 x 1/2 in 2 Pin (4.8 x 1/2 in . Screw (M4 x 10 mm 4 Velero Tape ...2
* Washer (5.2 x 24 x 2"1 2 Power Cord Bushing 1 Name Plate ...1
Warning Label ...1 Knob Label, Leg ...4 Dust ...
Operation Manual - Page 43
CRAFTSMAN 10 in 2
Front Block Slider ...1
Rip Fence Slider ...2 Front Block Slider ...1
• Washer (D16 × 25 x 1,6T 2 Rip Fence Assembly Ilncl. 1-22 1
"Standard Hardware Item - TABLE SAW -
FIGURE A: RIP FENCE ASSEMBLY 2
6
17 21
16
KEY
PART
NO.
May Be Purchased Locally 43 NUMBER
1
411071001
2
412011030
3
012101031O
4
0121010915
5
412011030
6
0121011801
7
...
Operation Manual - Page 44
...2 3
12 13
14
KEY NO.
1 2 3 4 G 6 7 8 9 10 11 12 13 14
k,
PART NUMBER
0121010222 412012705 412080702 9121015330302 0131010109-126 0101010917 0101010918 0121010803 0131O10329...x 16 x 1.5 1
NyTonNut ...1 Label ...1
Miter Gauge ...1 Center Pin (1/4 in 1 Index Pin ...1
* Tapping Screw (M4 x 10 ram 1 Indicator (M3 x 12 ram 1 Indicator Deck ...2
Tapping Screw, Pan Hd. (M4 x 12 mm 2 • Hex Nut...
Similar Questions
Changing Table Saw Motor To 240v
I have a 10" Craftsman table saw model #152221140. Lost the cover to the wiring which has the diagra...
I have a 10" Craftsman table saw model #152221140. Lost the cover to the wiring which has the diagra...
(Posted by mridude 9 years ago)
Table Saw Switch Malfunction
Today I pushed my switch on the table saw and it didn't turn off! I had to unplug the table saw. I s...
Today I pushed my switch on the table saw and it didn't turn off! I had to unplug the table saw. I s...
(Posted by gringoticahouse 11 years ago)
What Is A Sears Electronic 10'table Saw Worth
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
(Posted by mastercook76 11 years ago)
Miter Gauge Substitute On 137218070 Craftsman
Are there better miter gauges that will work on the137218070 Craftsman 10" table saw. The original i...
Are there better miter gauges that will work on the137218070 Craftsman 10" table saw. The original i...
(Posted by anoka114 12 years ago)
Is A Table Saw Motor From A Model 21807 Compatible With Other Saws?
will the 3HP 15 amp motor from a model 21807 mount properly on a model 137.248880 table saw (both ar...
will the 3HP 15 amp motor from a model 21807 mount properly on a model 137.248880 table saw (both ar...
(Posted by deannarandy 13 years ago)