Cisco WS-C3560E-24TD-E Support Question
Cisco WS-C3560E-24TD-E Support Question
Find answers below for this question about Cisco WS-C3560E-24TD-E - Catalyst Switch.Need a Cisco WS-C3560E-24TD-E manual? We have 2 online manuals for this item!
Question posted by halclark on November 28th, 2012
How Many Btu's Does This Unit Generate
The person who posted this question about this Cisco product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Cisco WS-C3560E-24TD-E Manual Pages
Installation Guide - Page 31
...19 20
21 22
23 24 23X
14X 24X
10/100 inline-power ports
Figure 1-6 Catalyst 3548 XL Switch
1 2
GBIC module slots
28010
SYSTEM RPS
12 1X
34
56
78
9 10
11... hubs through standard RJ-45 connectors and Category 3, 4, or 5 cabling
78-6456-04
Catalyst 3500 Series XL Hardware Installation Guide
1-7 Port 3 is above port 4, and so on the Catalyst 3512, 3524, 3524-PWR, and 3548 XL switches ...
Installation Guide - Page 32
... the 10/100 ports on the Catalyst 3512, 3524, 3524-PWR, and 3548 XL switches provide protocol support for speed and duplex autonegotiation, compliant with IEEE 802.3u. Cisco IP Phones-connected to workstations, servers, routers, and Cisco IP Phones, be set to switches or hubs, use Category 3 and 4 cables, but these features. When...
Installation Guide - Page 47
...refer to a powered-on the Catalyst 3508, 3512, 3524, and 3548 XL Switches
The Cisco RPS 600 (model ...switch is also connected to the Cisco Redundant Power System Hardware Installation Guide.
78-6456-04
Catalyst 3500 Series XL Hardware Installation Guide
1-23 Chapter 1 Product Overview
Rear-Panel Description
Internal Power Supply Connector
The internal power supply is an autoranging unit...
Installation Guide - Page 55
... of the geographic location of the cluster members. This network also includes voice and data subnetworks, where Cisco IP Phones are created by clustering the Catalyst switches except the Catalyst 4908G-L3 switch.
You can group the switches into multiple clusters, as illustrated, or into a single cluster. Each 10/100 inline-power port on the...
Installation Guide - Page 61
... Care must be grounded. Statement 20
78-6456-04
Catalyst 3500 Series XL Hardware Installation Guide
2-3 Chapter 2 Installing and Starting Up the Switch
Preparing for short-circuit (overcurrent) protection. Statement 42
Warning...equipment is intended to be given to connecting units to work on /off switch. To prevent airflow restriction, allow at least 3 inches (7.6 cm) of 113°F...
Installation Guide - Page 66
...Catalyst 3500 Series XL Cabling and Setup • This Catalyst 3500 Series XL Hardware Installation Guide • Cisco IOS Desktop Switching Software Configuration Guide • Release Notes for the Catalyst 2900 Series XL and Catalyst...the unit does not exceed 113°F (45°C). If any item is such that -
Preparing for Installation
Chapter 2 Installing and Starting Up the Switch
•...
Installation Guide - Page 67
...unit in the rack.
• When mounting this unit in a rack, you must take special precautions to a rack - Chapter 2 Installing and Starting Up the Switch
Installing the Switch...ensure your safety:
• This unit should be attached to the switch - Figure 2-1 shows which mounting holes...Installing the Switch in a Rack
Warning
To prevent bodily injury when mounting or servicing this unit in a...
Installation Guide - Page 75
... the power cord to an AC power outlet.
Connect one end of the unit. As the switch powers on the switch. When the switch begins POST, the port LEDs turn amber for ports 2 to ensure that... the system completes a test.
78-6456-04
Catalyst 3500 Series XL Hardware Installation Guide
2-17
As each turn green. Powering On the Switch and Running POST
If your management station. To ...
Hardware Installation Guide - Page 2
... manual generates and may cause interference with the limits for a Class B digital device in accordance with the instruction manual, may result in a particular installation.
Catalyst 3560 Switch Hardware ... interference stops.
• Move the equipment to one of its affiliates in the United States and certain other company. (1002R)
Any Internet Protocol (IP) addresses used...
Hardware Installation Guide - Page 11
... chapter provides a functional overview of how you can be deployed outside the traditional wiring closet environment, such as backbone switches, aggregating 10BASE-T and 100BASE-TX Ethernet traffic from other switches. and 48-port Catalyst 3560 switches can connect devices like workstations, Cisco Wireless Access Points, Cisco IP Phones, and other network devices such as...
Hardware Installation Guide - Page 19
...the same time, up to workstations, servers, routers, and Cisco IP Phones, be sure to switches or hubs, use the mdix auto interface configuration command to the powered device. Never: When you select the ...connected. Therefore, you can connect a Cisco IP Phone or Cisco Aironet Access Point to a Catalyst 3560 PoE switch 10/100 or 10/100/1000 port and to a maximum power output of 370 W. The...
Hardware Installation Guide - Page 28
... supply voltage is an autoranging unit that are diode-OR-ed into a single power block. Rear Panel Description
Chapter 1 Product Overview
The Catalyst 3560-8PC and Catalyst 3560-12PC-S rear panels have an AC power connector and heat sinks. (See Figure 1-18.)
Figure 1-18
Catalyst 3560-8PC and Catalyst 3560-12PC-S Switch Rear Panel
250607
1 2
1 Heat...
Hardware Installation Guide - Page 35
...safety:
• This unit should be accessible at...unit is rated not greater than: 5 A Statement 1005
Warning
To prevent bodily injury when mounting or servicing this unit...unit in the rack. Ensure that the system... power is the only unit in the rack.
• When mounting this unit in a partially filled ... protection. and 48-Port Switches)
Preparing for Installation
Warning Do not work ...
Hardware Installation Guide - Page 36
...and key or other means of a suitably installed ground conductor. Statement 1024
Warning This unit might have more than one power supply connection. Before you are made aware of ... the restricted access location are uncertain that could cause bodily injury. Statement 1074
Catalyst 3560 Switch Hardware Installation Guide
2-4
OL-6337-07 Use the statement number provided at the...
Hardware Installation Guide - Page 37
...unit does not exceed 113°F (45°C). You can be up to 328 feet (100 meters). • The cables meet the specifications in a closed or multirack assembly, the temperature around the switch...such as radios, power lines, and fluorescent lighting fixtures.
Catalyst 3560 switch SFP ports use shorter lengths of the switch should be sure to front and rear panels meets these ...
Hardware Installation Guide - Page 39
... rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in a rack, you must take special precautions to the Catalyst 3560 Switch, page 2-8 • Mounting the Switch in a Rack, page 2-10 • Attaching the Cable Guide, page 2-11
Warning
To prevent bodily injury when mounting...
Hardware Installation Guide - Page 59
... before mounting or servicing the unit in the fixed wiring. Statement 1022
OL-6337-07
Catalyst 3560 Switch Hardware Installation Guide
3-3 Statement 1008
Warning
This unit is removed from the bottom...than: 5 A Statement 1005
Warning
To prevent bodily injury when mounting or servicing this unit in a partially filled rack, load the rack from the DC circuit. Statement 1004
Warning...
Hardware Installation Guide - Page 60
... protection: 10/100/1000 Ethernet. Statement 1073
Warning Installation of security. Statement 1074
Catalyst 3560 Switch Hardware Installation Guide
3-4
OL-6337-07 Never defeat the ground conductor or operate the... connections must always be aware of the hazard. Statement 1024
Warning This unit might have more than one power supply connection. Statement 1030
Warning Ultimate disposal ...
Hardware Installation Guide - Page 61
...-panel indicators. - OL-6337-07
Catalyst 3560 Switch Hardware Installation Guide
3-5
If the switch is such that - Installation Guidelines
When you stack the switches or place them side by side. ...switch should be greater than normal room temperature. • The heat sinks and the bottom of this product is in Appendix A, "Technical Specifications." • Airflow around the unit...
Hardware Installation Guide - Page 64
...Desk or shelf 2 Screws
Step 3 Peel the adhesive strip off the bottom of the unit. This ensures that the two side-by-side slots face the front of the desk ...the accessory kit. Installing the Switch
Chapter 3 Switch Installation (8- Catalyst 3560 Switch Hardware Installation Guide
3-8
OL-6337-07 Note Wait before you attach the rubber feet.
and 12-Port Switches)
Desk or Shelf Mounting
•...
Similar Questions
Reset Switch Password
Could you advise how to reset cisco switch SR224
Could you advise how to reset cisco switch SR224
(Posted by downpose 3 years ago)
Need For Ios For 'cisco Catalyst Series 3500 Xl Switch'
I erased my switch's flash and I don't have ios to upload back to switch, would you tell me where I ...
I erased my switch's flash and I don't have ios to upload back to switch, would you tell me where I ...
(Posted by walidshabb 8 years ago)
Cisco Slm248g4ps - Small Business Smart Switch
This Switch does not have reset button, and i need to rest it !!!!!!i bout it second hand, and not h...
This Switch does not have reset button, and i need to rest it !!!!!!i bout it second hand, and not h...
(Posted by xmarkegypt 11 years ago)
Cisco 4506e Switch.
Cisco 4506E model Switch can support Fully routing including OSPF/BGP/EIGRP etc. with fully PBR(Poli...
Cisco 4506E model Switch can support Fully routing including OSPF/BGP/EIGRP etc. with fully PBR(Poli...
(Posted by manojpushpam 12 years ago)
How To Update Linksys Switch Firmware?
i have linksys switch SLM224G business series 24-port 10/100port Gigabit Smart Swirtch. Now i want t...
i have linksys switch SLM224G business series 24-port 10/100port Gigabit Smart Swirtch. Now i want t...
(Posted by rajasaqib86 13 years ago)