2009 Chevrolet Impala Support Question
Find answers below for this question about 2009 Chevrolet Impala.Need a 2009 Chevrolet Impala manual? We have 1 online manual for this item!
Question posted by nalurider79 on July 15th, 2013
Can't Remove Keys From Ignition
The person who posted this question about this Chevrolet automobile did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by sabrie on July 15th, 2013 8:19 PM
Try this one.
If it is a floor shift models it is a broken wire on the solenoid on the right lower of the shifter. Take the console out by unsnapping the trim from around the shifter and removing it. Next take out the screws (7mm, 2 of them on either side of the shifter) and there are 4 moreof the same size inside the cubby in the console, exposed by lifting tthe cubby lid,emptying the crap out of it and lifting the felt up. Take all of the screws out and then move the shifter to the 1st gear position and remove a phillips headscrew on the front of the shifter to remove the shift handle. Now lift out theconsole. You will more than likely see the broken wire when you look at the lower right side of the shifter close to the floor. Repair this connection by cutting all 4 wires leading to the harnessplug and splicing 4 extra inches of wire to each and also repair the connection that broke out of the harness plug. The only option I found was to buy a fuel pump wire harness repair kit to get the connecters needed. The problem is that GM did not put enough slack in the wires leading to the shift interlock solenoid and when repeated drive to park shifting is done will stress this connection. Sometimes it will make it not disengage the shift interlock solenoid and you can not get it into drivefrom park, other times it breaks the wire for the key release. This should fix your problems, otherwise you have a problem with the BCM. SHould save you all a ton of GM service department spending. Thank you for following
If it is a floor shift models it is a broken wire on the solenoid on the right lower of the shifter. Take the console out by unsnapping the trim from around the shifter and removing it. Next take out the screws (7mm, 2 of them on either side of the shifter) and there are 4 moreof the same size inside the cubby in the console, exposed by lifting tthe cubby lid,emptying the crap out of it and lifting the felt up. Take all of the screws out and then move the shifter to the 1st gear position and remove a phillips headscrew on the front of the shifter to remove the shift handle. Now lift out theconsole. You will more than likely see the broken wire when you look at the lower right side of the shifter close to the floor. Repair this connection by cutting all 4 wires leading to the harnessplug and splicing 4 extra inches of wire to each and also repair the connection that broke out of the harness plug. The only option I found was to buy a fuel pump wire harness repair kit to get the connecters needed. The problem is that GM did not put enough slack in the wires leading to the shift interlock solenoid and when repeated drive to park shifting is done will stress this connection. Sometimes it will make it not disengage the shift interlock solenoid and you can not get it into drivefrom park, other times it breaks the wire for the key release. This should fix your problems, otherwise you have a problem with the BCM. SHould save you all a ton of GM service department spending. Thank you for following
www.techboss.co.za
Related Manual Pages
Similar Questions
Key Is Stuck In Ignition Switch, And Will Not Turn Back Far Enough To Remove Key
(Posted by eeldeearl 10 years ago)
How To Get Ur Keys Out Of Locked Car Safely On A 2009 Impala
(Posted by mahoehi 10 years ago)
How To Remove The Blower Motor Under The Glove Box That Controls Air Vents?
It is making a banging noise when car is unlocked or even just sitting. It stops after about 5 minut...
It is making a banging noise when car is unlocked or even just sitting. It stops after about 5 minut...
(Posted by akamrswolf 10 years ago)
Ringing Bells
after removing key and open door the bells keep ringing and then the automatic starter will not work...
after removing key and open door the bells keep ringing and then the automatic starter will not work...
(Posted by wrichuk 11 years ago)
Can I Do The 'key Dance' To Determine Trouble Codes(check Engine Light Is On) ?
(Posted by davidmoes67 11 years ago)