Brother International XR-7700 Support Question
Brother International XR-7700 Support Question
Find answers below for this question about Brother International XR-7700.Need a Brother International XR-7700 manual? We have 1 online manual for this item!
Question posted by jgbloom80 on June 19th, 2012
How Do I Install The Quilt Guide On The Presser Foot? The Hole Is Too Small.
I have a Brother XR7700 sewing machine. I cannot fit the quilt guide into the small hole on the presser foot. I don't want to force it - it might break.
Current Answers
Related Brother International XR-7700 Manual Pages
Users Manual - English - Page 6
....
p Presser foot lever (page 16) Used to cut them. m Jack/socket connector (page 9) Insert the plug on the power supply cord into the jack/ socket connector.
n Foot controller jack/socket (page 10) Plug in the foot controller plug. q Foot controller (page 10) You can turn the main power and sewing light switch on the sewing machine model. e Thread guide...
Users Manual - English - Page 7
... guide.
When sewing is stopped, the needle is installed onto the presser foot holder.
Operation buttons
The operation buttons help you to raise and lower the presser foot. d Presser foot holder screw Use the presser foot holder screw to raise or lower the needle. a Presser foot lever Raise and lower the presser foot lever to easily perform various basic sewing machine operations...
Users Manual - English - Page 9
... Foot
2 Quilting Foot
3
1/4-Inch Quilting Foot
Part Code
U.S.A. / Canada Others
SA140
F033N: XC2214-002
SA129
F005N: XC1948-002
SA125
F001N: XC1944-002
No. Note
(For U.S.A.
KNOWING YOUR SEWING MACHINE
ACCESSORIES
The following machine models: CS-100, CS-6000, CS-6000i, CS-4000, ES-2400, ES-2000, EX-660, CE-4000, BC-1000, HS-1000, XR-7700
G The screw of the presser foot...
Users Manual - English - Page 15
..., see arrow a), and then press lightly on the foot controller and the machine starts to sew, you turn the power off while threading the machine.
Slide the button and open the cover. If bobbins from other models are used with the needle position button), and raise the presser foot lever.
14
1 a Tension-adjusting spring
Replace the...
Users Manual - English - Page 17
...Otherwise, the thread could tangle and break the needle. Raise the presser foot using the presser foot a lever. Be sure to turn...machine properly. a Presser foot lever
or
a Mark
b Needle position button
• If the needle is not correctly raised, the sewing machine can not be threaded. a Spool pin b Thread guide c Mark on the needle threader, see page 17.
KNOWING YOUR SEWING MACHINE...
Users Manual - English - Page 18
...sewing machine needles size 75/11100/16. If you are using transparent nylon monofilament thread, you can only use needles in the range of 90/14-100/16.
● You cannot use the needle threader if you guide...through the e thread take -up lever. Lower the presser foot lever. a Needle bar thread guide
Thread the needle from right to break.
Pull up
1
lever before you feed the upper ...
Users Manual - English - Page 24
... the needle hits the presser foot, the needle may bend or break. ● When using the twin needle, be sure to the needle bar thread guide. a Attach the twin needle in front of 5.0 mm (3/16 inch) or less, otherwise the needle may break or the machine may be damaged. ● When changing the sewing direction, be damaged...
Users Manual - English - Page 26
...the presser foot" (page 24).
a Screwdriver b Presser foot holder c Presser foot holder screw
25 Slowly lower the presser foot lever so that the g presser foot is securely attached. Removing the presser foot holder
Remove the presser foot holder when cleaning the sewing machine or when installing a presser foot that does not use the presser foot holder, such as the quilting foot.
a
•...
Users Manual - English - Page 28
... length or stitch width is selected.
If the needle hits the presser foot, the needle may result in the needle bending or breaking.
27 Press the stitch selection keys to the following example.
Turn on sewing with the stitches bunched together may bend or break.
● If the stitches are bunched together, increase the stitch...
Users Manual - English - Page 33
...) (1/64-3/16) ( J )
No
Rfc. **
ing, etc. a
Sew with the edge of the presser foot, and then
lower the presser foot lever.
b
1
• For details, refer to join together seams and finish them in one operation. If the needle hits the presser foot, the needle may bend or break.
32
a Needle drop point
a Guide
CAUTION
● After adjusting the stitch...
Users Manual - English - Page 35
... the fabric with the fold of the hem against the guide of the stitch width adjustment key. Check that the needle slightly catches the fold by pressing the "+" side of the presser foot, and
then lower the presser foot lever.
Sew with the edge of the stitch width adjustment key.
a Wrong side of fabric b Basting
c Desired...
Users Manual - English - Page 36
...15/64)
1.0 (1/16)
0.5-2.0 (1/32-1/16)
No
No
Auto* Rfc.
motion quilting, satin
stitching, button sewing
3.5 (1/8)
0.0-7.0 (0-1/4)
1.4 (1/16)
0.0-4.0 (0-3/16)
No Yes
*Auto Rfc.: Automatic Reinforcement **Rfc.: Reinforcement
The maximum buttonhole length is about 28 mm (1-1/8 inch) (diameter + thickness of the presser foot to the back, as shown below. Application
Stitch Width [mm...
Users Manual - English - Page 37
... used for sewing buttonholes, are indicated below.
1
2 5
■ If the button does not fit in the button guide plate Add together the diameter and thickness of the button, and then set the button guide plate to the calculated length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).)
1
3
4 A
a Button guide plate b Presser foot scale...
Users Manual - English - Page 38
... lowering the presser foot, do not push in the front of the presser foot, otherwise the buttonhole will not be sewn with the seam ripper, do not place your left hand, and then start sewing. Pull down the buttonhole lever as far as f possible. a Buttonhole lever
The buttonhole lever is completed, the machine automatically sews reinforcement stitches...
Users Manual - English - Page 39
... machine)
Use a handsewing needle to pull the gimp g thread to be attached.
c
1
a Button fitting foot "M"
38
Measure the distance between the holes in the illustration
so that it fits into...STITCHES
■ Sewing buttonholes on stretch fabrics When sewing buttonholes on with 4 holes can be attached. Buttons with 2 or with the sewing machine. Raise the presser foot lever, and ...
Users Manual - English - Page 45
... into the hole at a speed between the top and bottom layers of fabric is loose, the needle may result. UTILITY STITCHES
Quilting
Sandwiching batting between slow and medium.
■ Using the optional quilting guide Use the quilting guide to sew parallel stitches that the quilt b guide aligns with the walking foot, sew at a the rear of the walking foot or presser foot
holder.
†...
Users Manual - English - Page 47
.... Application
Stitch Width [mm (inch.)]
Stitch Length [mm (inch.)]
Auto Manual Auto Manual
Triple stretch stitch
Attaching sleeves, sew-
b
Start sewing. a Set the button guide plate on the presser foot scale is described below. c
• For details, refer to "Starting to strain, such as sleeve holes, inseams and pocket corners. J
02
02
02
02
ing inseams...
Users Manual - English - Page 52
... be damaged. Attach monogramming foot "N".
wing needle, otherwise the sewing machine
may bend or break. a
Sew together the right sides of the two pieces b of fabric, and then open up , and then sew over the seam allowance of fabric b 6.5 mm (1/4 inch) seam allowance c Straight stitch
Select stitch , or . If the needle hits the presser foot, the needle may...
Users Manual - English - Page 60
...presser foot. There are using is not Attach the presser foot that is correct
appropriate for the type of the guide...presser foot you want to put it still there, contact your retailer or the nearest authorized service center.
- page 52
The upper thread tension is too tight.
breaks.
If the thread is tangled in . page 57
The needle is not fitted properly. page 9
The sewing machine...
Users Manual - English - Page 64
... 6 25 , presser foot lever 6 16
pre-tension disk 11
Q
, quick-set bobbin 6 15
quilting 44 quilting foot 45 quilting guide 44
R
reinforcement stitching 46 reverse/reinforcement stitch button 6
H
handwheel 5 heirloom stitching 51
J
joining 51
, joining stitch 42 48
L
LCD 7
S
scallop stitching 49 seam ripper 37 sewing machine needles 20 sewing speed controller 6 sleeve holes 46...
Similar Questions
X-large Buttonhole
I have a button that is too large for the buttonhole foot. How do I make a larger buttonhole on my B...
I have a button that is too large for the buttonhole foot. How do I make a larger buttonhole on my B...
(Posted by Ginshorey 6 years ago)
Brother Sewing Machine Xr7700 How To Adjust Needle Position For Zipper Foot
(Posted by princje 10 years ago)
How Do I Install The W Embroidery Foot For The Quattro 6000d
(Posted by rmmiranda42 11 years ago)
Quilting Guide And Walking Foot
Hi: I purchased a quilting guide (a metal stick) that's supposed to be screwed into the foot of the...
Hi: I purchased a quilting guide (a metal stick) that's supposed to be screwed into the foot of the...
(Posted by blin9465 11 years ago)
How Do You Set The Needle On The 1/4 Inch Quilting Foot, It Doesn't Align Correc
(Posted by hornshari 12 years ago)