Brother International XL-5600 Support Question
Brother International XL-5600 Support Question
Find answers below for this question about Brother International XL-5600.Need a Brother International XL-5600 manual? We have 4 online manuals for this item!
Question posted by annchrisredding on September 27th, 2013
Bobbin Retaining Ring
SOmehow (kids) the bobbin retaining ring was lost on my machine for the Brothers XL -5600. Is it possible to get a replacement for this?
Current Answers
Related Brother International XL-5600 Manual Pages
Users Manual - English - Page 2
...10. This sewing machine is used by the manufacturer as threading the needle, changing the needle, threading the bobbin, or changing the presser foot. 15. Do not allow this machine to be supervised... to break. 12. Always unplug the machine before you change the light bulb. Replace the bulb with any other user servicing adjustments mentioned in this machine if it has a damaged cord or...
Users Manual - English - Page 4
... Lengths for Stitches 11 Stitch Length Dial ...13 Stretch Stitching ...13 Stitch Width Dial ...14 Reverse Sewing Lever ...14 Drop Feed Lever (if the machine is equipped with a drop feed lever 14
THREADING THE MACHINE 15
Winding the Bobbin ...15 Lower Threading ...16 Upper Threading ...18 Using the Needle Threader (models equipped with a needle...
Users Manual - English - Page 5
... lowers the presser foot. KNOWING YOUR SEWING MACHINE
PRINCIPAL PARTS
1 Bobbin-winding assembly (page 15) This winds the thread onto the bobbin, which you (counterclockwise) to raise and lower the needle. F Main power/sewing light switch (page 7) You can push this to control the sewing speed, and to start and stop sewing. G Foot controller receptacle (page 6) Plug...
Users Manual - English - Page 7
..., or damage to be used for the power source. Pulling on the cord. If the cord or plug is not to them. KNOWING YOUR SEWING MACHINE
USING YOUR SEWING MACHINE
WARNING
● Use only regular household electricity for a long period of time, otherwise a fire may result. Always grasp the plug to
remove it from...
Users Manual - English - Page 8
... foot off (toward the "I" mark) 2 Turn off the foot controller, the machine will start and you may bend or break and cause injury.
● Never sew with Models XL-5500/XL-5600/XL-5700/ XL-5510/XL-5610/XL-5710.
.
Other needles may be used with a bent needle. Main Power/Sewing Light Switch
This switch turns the main power and...
Users Manual - English - Page 9
...break or the machine may be damaged.
Using other any presser feet may be used with this machine. Release the foot... YOUR SEWING MACHINE
Raise the needle bar to its highest position by turning 1 the balance wheel toward the 5 back of the sewing machine may... Screwdriver
• Do not use the correct presser foot for smooth sewing. To check if the needle is bent or dull.
3
Changing the...
Users Manual - English - Page 11
... 20 21
■ 17 Stitches
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
■ 15 Stitches
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15
10 KNOWING YOUR SEWING MACHINE
THE CONTROLS
Pattern Selection Dial
To choose a stitch, simply turn the pattern selection dial in either direction. To select the first stitch when the last...
Users Manual - English - Page 13
KNOWING YOUR SEWING MACHINE
■ 17 Stitches Pattern
1
Stitch Name
1-STEP AUTOMATIC BUTTONHOLE
Recommended Width
[mm (inch)]
3-5 (1/8-3/16)
2
STRAIGHT STITCH
0-5 (0-3/16) (Changes needle position)
3
ZIGZAG STITCH
0-5 (0-3/16)
4
BLIND HEM ...
Users Manual - English - Page 15
... sewing for backtacking and reinforcing seams. To sew in reverse, push the reverse sewing lever in as far as possible and...sew forward. When monogramming, embroidering, darning or sewing on the dial represent the stitch width. Stitch Width Dial
Depending on the stitch selected, you lightly push the foot controller. To sew forward, release the reverse sewing lever. KNOWING YOUR SEWING MACHINE...
Users Manual - English - Page 16
... not operate correctly. Using of the clutch engaging when beginning to the machine.
● The bobbin was designed specifically for this sewing machine.
Put the bobbin onto the bobbin-winding shaft 3 and slide the bobbin-winding shaft to the
Note
● The machine stops automatically when the bobbin is not in the right place, the thread may cause damage...
Users Manual - English - Page 17
... it may break the needle.
1
2
1 Wound evenly 2 Wound poorly
1
2
1 Wound evenly 2 Wound poorly
● The bobbin was designed specifically for this sewing machine.
Open the shuttle cover behind the extension 2 table on the foot controller and the machine starts to break. Actual size
11.5 mm (7/16")
CAUTION
● Make sure you could be injured...
Users Manual - English - Page 19
...switch to "O". Pass the thread through the slit by pulling it toward you thread the machine properly, otherwise the thread could tangle and break the needle. Pull up lever to its... is in the wrong place, or is set incorrectly, the thread may tangle on this pin. KNOWING YOUR SEWING MACHINE
Upper Threading
1 2
4 3
1 Spool pin 2 Thread guide
CAUTION
● Make sure you (counterclockwise)...
Users Manual - English - Page 21
... as usual. (It is off when threading the needle by hand. The hook will pull the thread through the slit in the range of the sewing machine.
2
1 Bobbin case 2 Shuttle
Close the shuttle cover while pulling the 2 thread through the needle.
1
2 1
1 Hook 2 Thread
Quick Thread-Setting System FAST START...
Users Manual - English - Page 23
...Possible Problems If the Tension Is Wrong
Upper tension is "5".
22
2
1
2
1
1 Reverse 2 Surface
654
Note
● The lower thread tension has been adjusted at the factory for general use the needle threader to
thread the twin needle.
KNOWING YOUR SEWING MACHINE...then adjust the bobbin thread tension as explained below . For most sewing applications, no adjustment is too loose. If the...
Users Manual - English - Page 25
... a small needle (for the upper (spool) and lower (bobbin) threads. ● For clear nylon thread, always use needle 90/14 - 100/16. CAUTION
● Make sure you follow the needle, thread, and fabric combinations listed in the table. KNOWING YOUR SEWING MACHINE
CHART OF SEWING FABRICS, NEEDLES AND THREAD COMBINATIONS
Fabric Type
Mediumweight fabrics...
Users Manual - English - Page 41
... nearest service center. Needle is not threaded properly
in the shuttle hook. Page 18
No
Bobbin is incorrectly inserted.
Lower threading is bent or not sharp.
Page 18
No Page 16
...-18 No
Wrong needle is too
tight.
KNOWING YOUR SEWING MACHINE
Performance Checklist
Whenever sewing difficulties are encountered, first review the manual section about the operation that you are using ...
Accessory Catalog - Page 5
... stop at desired distance from the edge of the center guide. 3. Place each edge of two pieces of zipper. Sew holding coil to join them. Sew. Pin tucks: 1. SA184 All Brother home-use sewing machines
Ring Bearer Pillow & Hankerchief
Innov-is great for precise and easy joining of the fabric against the guide on the presser...
Accessory Catalog - Page 9
...
Useful for easy reference. Thread Cassette Wide Tables
Brother General Sewing Accessories
16
Thread Cassette
For sewing machines with /without a free-motion guide grip.
Conveniently placed ruler for quilting and other for your creation. One package includes ten bobbins.
11.5 mm 1/2"
SA156 ABCDEFGHIP
SA155 JKLMNO
9.2 mm 3/8"
Bobbins and Bobbin Clips
10 reusable high-quality and high...
Accessory Catalog - Page 15
While starting to sew, press the needle position button twice to pull the bobbin thread
to the machine. 2. Requires Low Shank Adapter for free-motion, outline quilting, etc.
1. Place the fabric beneath the presser foot. 4.
Walking Foot/Open Toe Walking Foot
Brother Quilting
Feet
28
Walking Foot/Open Toe Walking Foot
The feed dogs on...
Accessory Catalog - Page 36
... unique attachment to get needle felting effects easily on heavy weight materials such as canvas, polar fleece and fake fur. Brother Sewing Machine Attachments for PQ Series
69
Heavyweight Foot Ver y Narrow Foot Bobbin for PQ Series
Heavyweight Foot
An improved larger foot print assures better contact of wool roving or yarn on fabric...
Similar Questions
Xl5600 Brother Sewing
The balance wheel does not turn at all. What can I do to fix this problem?The
The balance wheel does not turn at all. What can I do to fix this problem?The
(Posted by patricif47 7 years ago)
How To Align Bobbin Case In Sewing Machine Brother Cs6000i
(Posted by carrCwb 9 years ago)
How To Replace A Needle On A Singer Sewing Machine Brother Ls 1217
(Posted by jarjeand 10 years ago)
The Thread Gets Tangeled In The Bobbin
what needs to be checked? I have tried just about every suggestion in the booklet.
what needs to be checked? I have tried just about every suggestion in the booklet.
(Posted by Anonymous-130873 10 years ago)
