Brother International SQ9050 Support Question
Brother International SQ9050 Support Question
Find answers below for this question about Brother International SQ9050.Need a Brother International SQ9050 manual? We have 4 online manuals for this item!
Question posted by younghouse39209 on November 29th, 2019
Machine Is Stuck In Reverse.
Sewing machine is stuck in reverse. Have cleaned it, turn it on and off, re-threaded it. How to fix. please send schematic. Something wrong in the inside.
Current Answers
Answer #1: Posted by marvintru on December 9th, 2019 7:12 AM
marvintru
Member since:
December 9th, 2019 Points: 13,190
Member since:
December 9th, 2019 Points: 13,190
Turn the machine off and hold the reverse button for 3-5 seconds. 7. Turn the machine back on and test to see if the machine will sew forward. If the problem persists, Contact Brother Customer Service for further troubleshooting by calling 1-877-Brother (1-877-276-8437) Monday through Friday, excluding holidays.
Related Brother International SQ9050 Manual Pages
Users Manual - English - Page 6
... equipped with character stitches 64
Selecting characters ...64 Checking characters ...66 Deleting characters ...66 Sewing the character stitches ...67
ADJUSTING STITCHES (for models equipped with character stitches 68
4. APPENDIX ...70
MAINTENANCE ...70
Cleaning the machine surface ...70 Cleaning the bobbin case ...70
TROUBLESHOOTING ...72 ERROR MESSAGES ...75
Operation beep (for models...
Users Manual - English - Page 8
... opposite direction.
Operation buttons
The operation buttons help you to sew" (page 29). Reverse stitches are sewn by keeping the button pressed down to sew in the sewing direction. For details, refer to "Starting to easily perform various basic sewing machine operations.
Pressing the button twice sews one stitch. Attach the appropriate presser foot for models equipped...
Users Manual - English - Page 10
...10 Needle set
11 Twin needle
12
Ball point needle (gold colored)
13 Cleaning brush
14 Screwdriver
15 Extra spool pin
16 Foot controller
Optional accessories
1.
2.
...XC4051-031 XE2137-001
8 Seam ripper
X54243-051
No.
KNOWING YOUR SEWING MACHINE
ACCESSORIES
The following machine models: HS-3000, SQ-9000, SQ9050, XR9500PRW.
● The screw of the presser foot holder is available...
Users Manual - English - Page 11
..., twisted, or bundled. Do not subject the cord to correctly operate the machine.
(For U.S.A. X The sewing lamp goes off when the
machine is being operated, turn off the sewing machine and unplug the power supply cord. Do not modify the plug in the outlet, reverse the plug. Electric shock may result in fire, electric shock, or damage...
Users Manual - English - Page 15
... fast) (for models equipped with
the sewing speed controller).
start/stop button). Slide the sewing speed controller to the right
h (to set the speed to be operated using the foot controller, connect the foot controller before turning on the machine.
● When the foot controller is turned after winding the thread around
the bobbin a few times...
Users Manual - English - Page 17
... used , the machine will make a clicking sound; a Cover b Slide button
Lower threading
Put the bobbin in so the thread comes out in the wrong direction, it may cause incorrect thread tension (page 31...cause the thread tension to sew, you could be incorrect or break the needle. Memo
● When the sewing machine is turned after winding the
thread around the bobbin, the machine will not ...
Users Manual - English - Page 18
...thread the machine as shown by turning a the handwheel toward you start to be used with the needle position button), and raise the presser foot lever.
Memo
● You can begin sewing immediately without drawing up the lower thread... the thread unrolls in the wrong direction, it may cause incorrect thread tension (page 31).
• Replace the cover so that the end of the thread comes ...
Users Manual - English - Page 20
... needle. a Needle bar thread guide
Thread the needle from right to
the needle bar thread guide. Lower the presser foot lever. The thread can only use needles in the range of the procedure in the wrong place, or is in a "Upper threading" to thread the machine to left hand, then feeding the thread with home sewing machine needles size 75/11100...
Users Manual - English - Page 22
...
b Needle position button
Pull on the wheel points up the lower thread
Lightly hold the end of both threads d and pull them toward you can begin sewing immediately without
cutting it there without drawing up the bobbin thread.
Draw up the lower thread by turning the
handwheel toward the back of the arrow, and leave it...
Users Manual - English - Page 24
...needle
Replace the needle as denim) with (needle position button), raise the needle by turning the handwheel a toward you (counterclockwise) so that has been determined to be skipped stitches...22 Before using the needle, place the flat side of the fabric, thread and needle is accidentally pressed and the machine starts sewing. Use the screwdriver and a needle that the
mark on the previous...
Users Manual - English - Page 26
... damaged. ● When changing the sewing direction, be sure to back. Put the second spool of the needle bar thread guide. a First spool b Second spool
Use the thread from front to raise the needle before turning the fabric. Thread the left needle from the first spool to thread c the machine to the thread take -up lever.
Other needles...
Users Manual - English - Page 29
...(page 28). For details on the machine" (page 9).
Turn on the machine. Before operating the sewing machine, read the following precautions.
2
CAUTION
● While the machine is finished, cut the threads.
2 SEWING BASICS
SEWING
Basic sewing operations are described below to sew.
1
Turn on the sewing machine. General sewing procedure
Follow the basic procedures below .
Attach...
Users Manual - English - Page 31
... 29).
b
a Presser foot lever
Place the fabric under the presser foot, pass c the thread under the presser foot, and then
pull out about 5 cm (2 inch) of the machine. Continuing to sew with your left hand, turn the handwheel toward you (counterclockwise) so that the needle does not touch the presser foot.
If the needle...
Users Manual - English - Page 32
... (reverse/reinforcement stitch button) sews reinforcement stitches, 3 to 5 stitches on top of the machine, k and then pass the threads through the thread
cutter to the left or right to "STITCH SETTINGS" (page 35).
30 a Sewing speed controller
Slowly press down on the wheel points up. (With models equipped with (needle position button), raise the needle by turning...
Users Manual - English - Page 37
...)
No
Rfc.
*Do not use reverse stitching.
**Select a stitch width of 5.0 mm (3/16 inch) or less, otherwise the needle may break or the machine may
be damaged. ● When ...Center
Triple stretch stitch
Stretch stitch
J
01
01
01
01
01
01
Attaching zippers, basic 01 stitching, and sewing
gathers or pintucks, etc.
3.5 (1/8)
0.0-7.0 (0-1/4)
2.5 (3/32)
0.2-5.0 (1/64-3/16)
Y*e*s ( J )...
Users Manual - English - Page 52
... toward you h (counterclockwise) to cut the upper thread and the bobbin thread at the beginning of the fabric, and
then tie it is positioned at low speed, press (reverse/reinforcement stitch button) to the shortest setting by g pressing the stitch length adjustment key.
Start sewing. When you . Turn the handwheel toward the rear of the...
Users Manual - English - Page 57
Reverse stitches cannot be quilted...strike the presser foot and cause injury.
● Be sure to turn the handwheel toward the front of the machine to "Removing the presser foot holder" (page 26).
Do not...Hook the connecting fork of the presser e foot, and then evenly guide the fabric while
sewing. Quilts can easily be sewn using the optional walking foot and the optional quilting guide....
Users Manual - English - Page 61
...-1/4)
2.5 (3/32)
1.5-4.0 (1/16-3/16)
No
No
Rfc.
*Select a stitch width of fabrics, such as with this sewing machine.
Smocking stitching and decorative stitching
5.0 (3/16) 1.6 (1/16)
0.0-7.0
1.0-4.0
(0-1/4) (1/16-3/16)
Ye*s ( J )
...50 stitches model 40 stitches model Twin Needle Walking Foot Reverse (Rev.)/ Reinforcement (Rfc.)
Stitching
Various decorative stitches can be sewn with tricot
5.0...
Users Manual - English - Page 72
...therefore, it should be injured.
CAUTION
● Make sure you unplug the machine before cleaning the machine, otherwise injuries or an electric shock may get an electric shock or be cleaned periodically. APPENDIX
4 APPENDIX
MAINTENANCE
Simple sewing machine maintenance operations are described below. After cleaning it once with a wet cloth, wipe it . CAUTION
● Unplug the power...
Users Manual - English - Page 77
... operation.
4
The reverse/reinforcement stitch button or needle Move the bobbin winder
position button was pressed while the bobbin winder shaft to sew.
75
Be sure to check for four seconds and the machine automatically stops. ERROR MESSAGES
If an operation is performed incorrectly before the sewing machine is set up because the thread is tangled...
Similar Questions
Pe 500 Embroidery Machine Can Only See Bobbin Thread
(Posted by forrcoolth 9 years ago)
How Do I Get Upper Thread That Has Broken Off Inside, Out Of The Machine?
My upper thread has broken and when pulling the thread off the spool to rethread, it broke off insid...
My upper thread has broken and when pulling the thread off the spool to rethread, it broke off insid...
(Posted by lindyloufreespirit 10 years ago)
My Bobbin Will Not Turn In My Sq9050 Sewing Machine, Why?
(Posted by Doc1maka 10 years ago)
Brother Sewing Machine Sq9050 What Type Bobbin
(Posted by Marbl 10 years ago)
How To Oil My Brother Sewing Sq9050 Machine
(Posted by leoeliogd 10 years ago)