Brother International BES-1210AC Support Question
Brother International BES-1210AC Support Question
Find answers below for this question about Brother International BES-1210AC.Need a Brother International BES-1210AC manual? We have 13 online manuals for this item!
Question posted by embroidery on September 26th, 2012
My Power Is On But The Machine Is Doing Nothing
My power is turned on but the machine is doing nothing. What is wrong??
Current Answers
Related Brother International BES-1210AC Manual Pages
Instruction Manual - English - Page 4
... voltages are noticed, immediately turn off the power switch. Ssol
Do not connect the power cord until installation is complete, otherwise the machine may operate if the foot switch is not taken, incorrect machine operation may result. Then contact your nearest Brother dealer or a qualified technician. Avoid setting up the sewing machine near sources of children.
The...
Instruction Manual - English - Page 5
...cause vomiting and diarrhoea.
If any maintenance and
inspection of the sewing
If the power switch needs to wear protective goggles and gloves when handling the ...
A Maintenance and inspection of the electrical system.
0
Turn off the power switch before using the machine. Any problems in injury. BES-1210AC
III
Ask your Brother dealer or a qualified
electrician to...
Instruction Manual - English - Page 6
... or are difficult to the sewing
machine.
5 Direction of operation
IV
BAS-416A • BES-1210AC switch and unplug Gehauses
couper le contact
Antes de abrir esta
power cord before changing needle, cleaning.... Please follow the instructions on the sewing machine. Never touch or push the thread take up during operation as it may cause injury. Turn off main
Vor Offnen des
Pour ouvrir...
Instruction Manual - English - Page 12
...method Stitch length Storage medium
Thread trimming Needle thread breakage
Power supply Weight
Dimensions Options
• BES-1210AC Embroidery machine used Application Sewing speed Sewing area
Feed method Stitch length Storage medium
Thread trimming Needle thread breakage
Power supply Weight
Dimensions Options
2
9 needle embroidery machine Pattern embroidery Maximum 1200 spm ( 4 levels) V 300 mm...
Instruction Manual - English - Page 17
... will appear as shown on the power of the needle plate. When the needle bar case comes to turn or does not turn the shaft forcefully.
' CAUTION MOVING!
and "Press START key" are displayed
N Case PO5. BAS-416A BES-1210AC
7 The machine cannot operate under this condition.
1. If it . Turn the shaft © slowly. Error Set...
Instruction Manual - English - Page 28
... into the design floppy disk. Operation of the display.
DST
18
6.
Default sewing of patterns
Following is displayed on the Power.
(Fi le No. 01
2. stoGcnEAr,
STAFF
WE CREATE THE NEXT APPAREL GENERATION BROTHER INDLISTRA LTD. Turn on the lower row of Machine
1. Insert the design floppy disk. EEO •DELUDE= / Disk
(71: DOEIDOODO...
Instruction Manual - English - Page 36
... the machine is turned on the power. Pressing the key wi l l cancel sewing.
26
BAS-416A • BES-1210AC Restarting
In the following cases, sewing can be resumed. Co. 0 E
N- When the machine is automatically suspended because of a power loss during sewing, or if the power switch is suspended during sewing. Turn on after having been turned off during suspension or sewing:
Turning...
Instruction Manual - English - Page 37
... passed with the power off because of a power loss
Restart > START Sew. BAS-416A • BES-1210AC
27 Cancel" are displayed. Turning on the power. Sewing (CAUTION MOVING! Cancel > END
1. Turn on the power will display the main menu. Pressing the key will be erased and the restart cannot be done.
In case the power of the machine was cut off...
Instruction Manual - English - Page 47
... correct sewing. To display the hoop name for the tape reader or editing system to 4800 bps (The speed can be set to OFF when shipping. BAS-416A • BES-1210AC
37...data reading or sewing of a pattern (character), machine will continue reading or sewing until it is done.
If the power is inserted during data reading and sewing.
If another floppy disk is not turned off, functions ...
Instruction Manual - English - Page 48
....,`c4•5)
•
E EE E 7.. '
=E ...
.. If the power is 1000 spm)
To set sewing start point of editing system data to first stitch
To set sewing start point of editing system data to center of the machine should be turned off , functions do not change.
38
BAS-416A • BES-1210AC switch number SW1 SW2 SW3 SW4...
Instruction Manual - English - Page 56
...Select the number of paper tape reader, also.)
2. The machine will go into the data entry mode. * Up to select...1210AC Press the < < > key or < D> key. Press the key. Press the key or key to select paper tape type from paper tape
CAUTION MOVING!
[Fi leNo.0 1
[n`
* ** ** *
1. Entering data from TAJIMA, BARUDAN and ZANGS.
6. Turn on the power. (Turn on the power of machine...
Instruction Manual - English - Page 59
Turn on the power of machine side.
3. ODD On line /Editor
[.:01 EICIEDIIIECIO. =El File Sel / Editor
ENTER I ...machine will go into the data entry mode.
4. After selecting the file name, press the < ENTER> key. EDE EEOOOOO17 /Editor
2. BAS-416A • BES-1210AC
49 CAUTION MOVING!
Entering data from BAS-PC/EM system
NOTE: The BAS-POEM is sold separately.
Turn on the power...
Instruction Manual - English - Page 76
...)
' it can show the messages with beep sound when starting next sewing. Enter the set from this setting
66
BAS-416A BES-1210AC Also, ON/OFF of thread breakage detection can be switched. • The bobbin thread counter can be set value
To exit from 0 to set before ...
Instruction Manual - English - Page 85
... automatically enter into flat frame mode. • When the power is turned on with the clamp switch being pressed in the flat frame mode, the machine will go into the air clamp mode. • For the BAS-416A • BES-1210AC, refer to page 9 of frame type on operation panel
Flat frame mode
Maximum...
Instruction Manual - English - Page 86
...power has been cut off.)
The way of operation
THREAD SENSOR .,
pr B.
T. Count : DE / ED \.5 T. When keys are kept in the machine... by the unit of 10 mm. * 0: Short S 80 : Long NOTE: When the PROM version is A or B for thread pulling ranges from the material at time of thread trimming while sewing... key twice.
3. BAS-416A • BES-1210AC Count: ED / ED
T TRM
=80
END...
Instruction Manual - English - Page 87
... and stitch counter, press the key three times. Not Sew
END
i
END
3. BAS-4164 • BES-1210AC
77 Count: EDElil l=
THREAD
' TRIMMING
I
-N
THREAD...Sew
1. T. END
/ B.
Co. Press the key to turn sewing on the operation panel whether to sew 0 mm stitch or not, which exists in the sewing data. (At the time of power having been input, the machine is always set to "sew...
Instruction Manual - English - Page 88
... alarm, in the case of the machine having been stopped due to operation
THREAD SENSOR
B.T. T. Count : 99 / 99 ALARM = BUZZAR
*
B. T. Co. u 1]
N No.IICIODEOCIEE
78
1. After setting is turned off.)
The way to thread breakage during sewing. (The value set will remain stored in the backup even when the power is completed, press the key...
Instruction Manual - English - Page 107
... position. Turn pulley till needle bar is displayed again, turn the power off . X ORG. Back-up data in sewing mode.
...page 34.)
Message in this mode. Input data has something wrong. Disk ERR.
Error
Damaged circuit board, sensor defective, cable... defective.
• X home position sensor is removed when machine runs in the memory disappears.
Error Messages
Refer to the...1210AC
97
Instruction Manual - English - Page 108
... on power. This data cannot be set machine to communication mode.
Contact your dealer.
Turn on thread
breakage detector. • Bobbin thread breakage • Bobbin thread has run out. Entered data has something wrong. Wait till communication ends.
98
BAS-416A • BES-1210AC Area Over B.Thread empty Thread breakage
Motor Lock
Cause
Without sewing data...
Instruction Manual - English - Page 112
...sewing area.
12. Upper shaft is over the area.
Turn the power off, and then while pressing the key, turn .
• Is thread tangled in the BAS-416A service manual.
13. Thread breakage detector functions and machine...stud operation normal? (Is spring tension proper?)
102
BAS-416A • BES-1210AC Check point
• Is thread take-up , then re-tighten it.
• Is position of...
Similar Questions
How Does One Set A Bes-1210ac To Trace A Design Before Sew Out?
(Posted by jerseytees 5 years ago)
What Is The Power Supply Of Brother Sewing Machine
(Posted by Aflichas 9 years ago)
Quattro 6000d Lemon?
My wife bought a new Quattro 6000D 2 1/2 years ago, has had it serviced by Brotheer (Moore's sewing)...
My wife bought a new Quattro 6000D 2 1/2 years ago, has had it serviced by Brotheer (Moore's sewing)...
(Posted by KDBJGH 10 years ago)
I Am Trying To Work The Machine But I Am Having Troouble?
(Posted by rolarrbarnes 11 years ago)
Machine Will Not Change Needle Position
The machine is locked up and will not change needle position.
The machine is locked up and will not change needle position.
(Posted by jstorts 11 years ago)