Bosch HGI8054UC Support Question
Bosch HGI8054UC Support Question
Find answers below for this question about Bosch HGI8054UC.Need a Bosch HGI8054UC manual? We have 2 online manuals for this item!
Question posted by Tingwinkl on June 14th, 2016
How Do You Install The Anti Tip Brackets To The Oven?
do the brackets have to be drilled into the wooden floor or can they be attached towards the top
Current Answers
Answer #1: Posted by waelsaidani1 on June 15th, 2016 2:52 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
Hello follow instructions here: http://www.prettyhandygirl.com/installing-anti-tip-bracket-for-your/
Related Bosch HGI8054UC Manual Pages
Installation Instructions - Page 3
...Overall Dimensions 5 Location Level and Plumb 5 Installation Hints 5 Electrical Requirements 5 Cabinet Requirements 6 Install Ventilation 6 Required Clearance 6 Prepare Walls and Floor 6 Countertop Requirements 6 Installation Procedure 7 Installation of the anti-tip bracket 7 Apply Foam Tape 7 Electrical Connection 7 Connect Electric Range Cord 7 Connect Electric Flexible Conduit 10...
Installation Instructions - Page 5
... or licensed by removing leveling legs, panels, wire covers, anti-tip brackets or screws, or any other servicing should not move more than 36 inches.
• Installer -
Improper installation, service or maintenance can cause injury or property damage.
Verify that the anti-tip bracket engages the range leg and prevents tip-over and be converted for guidance.
All other...
Installation Instructions - Page 6
...before using the range.
Children climbing on a separate branch circuit. Installation, electrical connections ...oven door for data plate location. Hidden surfaces may have sharp edges. Never allow children to play with a cord and plug, do not remove leveling legs, panels, wire covers or anti-tip brackets/screws.
Be sure your appliance is properly installed and grounded by installing...
Installation Instructions - Page 7
... kit be made by a qualified technician.. Your gas range model is not installed by a qualified installer or electrician. IMPORTANT SAFETY NOTICE: The California Safe Drinking ... to Liquified Petroleum Gas
.
9 WARNING Personal injury or death from electrical shock may occur if the range is designed to such substances. Any additions, changes or conversions required in order for this appliance to ...
Installation Instructions - Page 8
... (depending on mounting surface) • Level • Drill and Drill Bit (3/16" masonry bit for concrete
screws) •... installing the range, be sure to verify the cabinet dimensions are correct for lifting.
___ 4. Reinstall the oven... installations, cord is not necessary for Anti-Tip Bracket (Style
will vary depending on local code). Installation Checklist
Please refer to Protect Floor)...
Installation Instructions - Page 9
... stable location unitl you are ready to reinstall it from the closed during installation, remove the range oven door (see door removal/reinstallation in the Use & Care Manual maintenance section...of cardboard or cloth under the range during installation, could jeopardize the seal around the cooktop and may cause damage to countertops and floors during installation to move. MED LOW HIGH ...
Installation Instructions - Page 10
...
We recommend that the present electric service to data plate for the kW rating. Note: In Canada, the range is shipped from the floor. Most wiring codes require a separate circuit with the range power cord already installed. English 7 The 120 VAC outlet can be 120/240 volt, 30 amperes minimum. Verify that wiring to...
Installation Instructions - Page 11
...range.
Note: The slide-in the U.S. (In Canada, 12 mm clearance is at least 4" (10.2 cm). Install Ventilation
Bosch strongly recommends the installation... cabinet storage is recommended. In this range. For most noticeable with laminated cabinets....installed. The minimum clearance from range top to adjacent vertical walls must be at least 30" (76.2 cm). The range hood must be installed...
Installation Instructions - Page 12
... holes in the walls or floo. Ensure the anti-tip bracket is engaged when the range is not installed. Position the bracket as shown below in place. Do not use wood or anchorless concrete screws (included). Screws should provide fim attachment into solid wood or flooring. The range can tip the range over and be left open at the back of...
Installation Instructions - Page 13
... the appliance is to install the strain relief: Remove panel from the factory with your strain relief.
1. Once cord length/slack has been adjusted, attach strain relief per instructions ...) can be installed per instructions included with Ranges". Strain relief provided with cord. Frame grounded to neutral through hole and strain relief up to gas ranges). Tip: The knockout panel...
Installation Instructions - Page 15
... be connected via flxible conduit. Replace the nut/washer on each terminal post.
4. For installations other than those in place to anchor the internal wiring attached to expose the
terminal block. 3. Attach the white wire to 20 in range at the breaker box. 2. Remove the green grounding screw from the factory with this method...
Installation Instructions - Page 17
... box.
Don't forget to avoid damage.
2.
It is now complete. Install male 1/2" or 3/4" flare union adapter on the elbow fitting to relight the pilot on other gas appliances when you turn the gas back on range and at knockout pa-nel on .
Attach Connector
Note: DO NOT plug in /lbs) Torque (Nm)
6
35...
Installation Instructions - Page 18
... this section. Wipe off supply line gas shutoff valve and tighten connections. 5.
The configuration of the installation. The gas connection is complete. It is to be conducted by the installer according to the instructions given in the range if connections may have been disturbed during rigid pipe testing.
1. Connect to regulator here
B
Pipe...
Installation Instructions - Page 19
... in power cord. 2. NOTICE
To avoid risk of cooktop trim (B). Take care not to the range oven door, do not lift, push or pull the range by the anti-tip bracket. Plug in right back corner. Tip: Remove the range warming drawer to crimp the flexible electrical connector. Also verify that both back legs are resting solidly on...
Installation Instructions - Page 20
...The drawer should insert easily.
Open and close , verify that the oven light comes on the housing to preheat. 4. Test for detailed operation... ignitor/spark module clicks. Otherwise, continue with the rails attached to be straight, not crooked. Open door all the way...the drawer housing.
3. Turn on the bracket.
6. Select the BAKE mode. See the Use and Care Manual...
Installation Instructions - Page 21
... service for the correct fuel. Yellow Flames: Further adjustment is normal during the initial start-up. Yellow Tips on Outer Cones: Normal for more information. 4. If the flame is completely or mostly yellow, verify ... color.
Allow unit to the low setting. 3.
Otherwise, the installation is complete. Soft Blue Flames: Normal for more information.
4.
After adjustment, retest.
Installation Instructions - Page 5
...the regulator, the inlet pressure must be 5' in length (Exception: Maximum connector length in Massachusetts installations is 3'). Pop out the plastic stem in the cap and turn
breaker off at least 1" ...supply line. Use this kit to the gas supply. Observe the following: Be sure the range is reached. shut off the outside propane tank gas valve to disconnecting the electrical power.
...
Installation Instructions - Page 6
...4. If your range is dual fuel your conversion is located inside the oven cavity at the top right (visible with 5 screws.
Use 1/2 inch (13 mm) wrench to "Test the Installation" on burner ..., placement can be properly positioned on page 4. Tighten until it stops (bypass screw is attached to the top of card for Propane Use
1. Replace screws. Place natural gas orifices in Use...
Installation Instructions - Page 7
... leak detection fluid to the next step until it through the access hole in the gas connection between the shutoff valve and the range. Retest for leaks by the installer according to reinsert all leaks are eliminated. 4. When leak check is complete (no bubbles appear), test is located below the air shutter...
Installation Instructions - Page 8
...flame goes out, does not carry over properly, adjust the bypass jet. Dual Fuel appliance installation is located on page 3. The air shutter is complete when correct color, carryover and size ...right color. If any flame burns yellow, contact Service.
Test each cooktop burner. Yellow Tips on Outer Cones: Normal for proper lighting, proper flame characteristics on the low setting and...
Similar Questions
Gas Range Exploded. Anyone Else Have Problem?
Gas range, model HGS7152UC exploded. I live in New York. Anyone else have problem. This model was re...
Gas range, model HGS7152UC exploded. I live in New York. Anyone else have problem. This model was re...
(Posted by ehn144ony 7 years ago)
Bosch Convection Range And Oven Combo How To Reset A Fault Code Of Er22
We own a Bosch range and oven combo HES7252U. The stove top module keeps displaying the following er...
We own a Bosch range and oven combo HES7252U. The stove top module keeps displaying the following er...
(Posted by nmcbncr20 8 years ago)
Bosch Dual Fuel Range/oven Model # Hd17152u/03
The oven will not heat up after trying several different heating settings.
The oven will not heat up after trying several different heating settings.
(Posted by dellga01 9 years ago)