Bosch DS150I Support Question
Bosch DS150I Support Question
Find answers below for this question about Bosch DS150I.Need a Bosch DS150I manual? We have 1 online manual for this item!
Question posted by Jevo6545 on January 29th, 2020
Wiring To A 2 Door Ip Controller
What wiring is required to get this to work
Current Answers
Answer #1: Posted by Troubleshooter101 on March 5th, 2020 9:28 AM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,030
Member since:
September 30th, 2015 Points: 2,927,030
A typical access control system set up will have these four main components: card reader/keypad, door contact, request toexit and lock power device connectivity. What this composite cable does is to simply
Please check this link below:
https://www.getkisi.com/guides/cables-and-wires
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Related Bosch DS150I Manual Pages
Installation Guide - Page 1
... to Plug Orientation (Default Switch Settings)
The DS150i is also available in a light grey (DS150i) or a black (DS151i) enclosure. control units, power supply and locks). The latch time features two modes of the door or doors to 64 sec.
Where aesthetics are made and inspected. Figure 4: Relay Contact Wiring
The arrows on the ceiling or wall...
Installation Guide - Page 2
... the detector first sees motion. Hint: This setting works best when used for .... Figure 5: Wiring the Bridge Rectifier
DS150i Relay Contact (non-spike protected)
DS150i Relay Contact (... require the bridge rectifier or diode as a magnetic door ...door lock or electric door strike). If enabled, the LED operates normally when motion is ready to be installed in conjunction with an access control...
Installation Guide - Page 3
... settle. 3. After confirming proper operation, replace the cover and walk test
one more time to ensure the coverage has not changed.
6.0 Other Information
Single Door Use: The pattern can be masked to obtain the proper
coverage.
Apply power to Figure 7). 5.0 Setup and Testing
1. Test the unit by walking directly through...
Installation Guide - Page 4
.../NFPA 70 and part 1 of the Canadian Electrical Code CSA C22.1, Safety Standard for each of standby time required. Push to Exit Alarm will Sound
Push to Exit Alarm will Sound
K,L I,J
K,L I,J
G,H E,F
A,B ...of 4 While the gap is no internal standby battery. Install a DS150i over each hour of the two doors and wire the
outputs so either detector permits exiting. Two Form "C" contact sets...
Similar Questions
Dip Switch Settings Configuration Diagram For Bosch Ds150i
Could you please email me the dip switches configuration diagram of Bosch Model DS150I. The diagram ...
Could you please email me the dip switches configuration diagram of Bosch Model DS150I. The diagram ...
(Posted by procesoorda 8 months ago)
Wire Digram Of Bosch Isn-sm-50
i need the wire digram that to connnect the bosch isn-sm-50 and test it
i need the wire digram that to connnect the bosch isn-sm-50 and test it
(Posted by abdohaju 11 years ago)
Sensitivity Settings On Ds835 Motion Sensor
I need to know if the sensitivity of DS835 can be adjusted
I need to know if the sensitivity of DS835 can be adjusted
(Posted by hemmathur 11 years ago)
Connection Details
How to connect Bosch DS937 motion sensor to switch on the light?
How to connect Bosch DS937 motion sensor to switch on the light?
(Posted by kememk 11 years ago)