Bosch 4100 Support Question
Bosch 4100 Support Question
Find answers below for this question about Bosch 4100 - 10 Inch Worksite Table Saw.Need a Bosch 4100 manual? We have 1 online manual for this item!
Question posted by twisted7 on September 9th, 2012
Have A Bosch 4100 Table Saw And When You Feed Wood In The Blade Slows Down
The person who posted this question about this Bosch product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Bosch 4100 Manual Pages
Operating Instructions - Page 3
... tools, wood scraps, etc., except the workpiece and related feed or support devices for ripping widths of your saw in place for all "THRU-SAWING" operations (sawing entirely thru the work until it where neither the operator nor the casual observer is the same as that contact the rear of operation. General Safety Rules 2-5 2. Maintaining Your Table Saw...
Operating Instructions - Page 4
... down or support the workpiece, remove wood scraps, or for the operation being performed. NEVER use the maximum diameter blade for which the saw was designed.
NOTE AND FOLLOW SAFETY INSTRUCTIONS THAT APPEAR ON THE FRONT OF YOUR TABLE SAW.
4. DO NOT remove small pieces of the cutting tool rotates toward you stall or jam the...
Operating Instructions - Page 5
...can shock, burn or
electrocute.
! IMPORTANT: Servicing of tool. Extension Cords
! Use of work. If in Feet
25 50 100 150
3-6 6-8 8-10 10-12 12-16
18 16 16 14 18 16 14 12...(one blade is a design concept used to use of any way. THINK SAFETY SAFETY IS A COMBINATION OF OPERATOR COMMON SENSE AND ALERTNESS AT ALL TIMES WHEN THE TABLE SAW IS BEING USED.
! Double Insulated Tools
Double ...
Operating Instructions - Page 6
... Rules 2 Additional Safety Rules 3-5 Double Insulated Tools & Extension Cords 5 Table of Contents 6 Glossary of Terms 7 Tools Needed For Assembly 7 Getting To Know Your Table Saw 20, 22
Power Switch 20 Table 20 Base/Sub-Base 20 Blade Bevel Lock Handle 20 Table Extension 20 Table Extension Lock Handle 20 Elevation Wheel 20 Blade Bevel Scale 20 Rip Fence Scale 20...
Operating Instructions - Page 22
.... FIG. 1
19
21
2 10
18 12
59
20. TABLE INSERT Removable for fence settings with a greater level of three key elements: Adjustable (3 position) Riving Knife, Anti-Kickback Device, and Barrier Guard Device. DIGITAL CARRIAGE (MODEL 4100DG-09 ONLY)
22
Provides a digital readout for removing or installing blade or other cutting tools.
22. SMART GUARD...
Operating Instructions - Page 24
... missing, do not plug the power cord into a source of power. Model 4100 Table Saw is not removed.
4
7
2
3
1
8 24.
FIG. 3
5 6
Table of Loose Parts to raise blade if styrofoam is shipped complete in the power cord or
turn the switch on the table saw , plug in one with the illustration and the list of Loose Parts
ITEM...
Operating Instructions - Page 30
...Blade
IMPORTANT: The saw blade provided on this tool. Bosch offers an extensive line of .092" or more .
! The replacement blade's plate thickness must select a blade with a kerf width of Premium-Quality Professional Saw Blades...until the blade is .086" thick. When looking for this saw blades. The kerf of table and push down and secure in place. If the
replacement saw blades made ...
Operating Instructions - Page 38
Aligning Rip Fence
!
Your table saw is equipped with the desired dimension on lower scale 8, then re-tighten screw 9 (Fig. 24). WARNING
To prevent personal injury, always make sure the fence stayed parallel to the blade.
5. If rear is moved side to be non-self aligning (Fig. 23). Rip Fence Pointer Adjustment
The distance...
Operating Instructions - Page 42
...tilt until it touches the tips of the Saw Blade 2 -
Fully tighten Clamp Screws 8 with table saw blade.
! The Riving Knife 1 is near .100", use 2 thicknesses.
7. Raise the Saw Blade 2 to maximum height and set the bevel ... squareness of base). Place the Rip Fence 3 on the Bosch blade included).
if the kerf is thinner than the width of paper as a "Spacing Gauge"....
Operating Instructions - Page 44
... table saw ), (Fig. 31).
Main barrier guards, Anti-kickback device, and riving knife. The side barriers (one to the left and one to "catch" the material in
FIG. 31
FIG. 32
3 1
44. Attachment/Removal
(see page 26 for additional tools. Because of this process in the event of one another, maintaining maximum blade coverage...
Operating Instructions - Page 46
...2
4 3
31
Blade Bevel Control
Loosen blade bevel lock handle 1...table extension.
!
FIG. 36
4 2
5 46. The Anti-Kickback Device can be locked in its full height).
To secure table...table (while the blade is at desired angle and tighten blade...Table Extension
To extend the table, raise the table extension lock handle 4 (Fig. 35) and slide table...table insert, raising the blade to its full height...
Operating Instructions - Page 48
... fence 9 or parking plate 10.
Position the 4100 table saw 's rip fence 9 to make rip cuts without using a high quality 9 Volt Alkaline Battery. Put the battery into its package.
The 4100 table saw 's blade and the working side of the fence before the operator makes a rip cut.
Battery cover 7: (not shown) opens to show inch (3 mode variations) or metric...
Operating Instructions - Page 58
... the 4100 table saw. CLEANING AGENTS: Do not use any cuts that do not use the fence, the digital carriage should always be
set at 0 bevel).
1) Pull up to be removed, unplug the saw and unplug the power cord before cleaning. The digital carriage cannot be in the "parking position".
DIGITAL CARRIAGE PARKING POSITION
10...
Operating Instructions - Page 60
... Not Extended
The rip fence pointer shows the distance from the blade to table.
When cutting the workpiece, line up to mark and locate exactly where the blade will enter
the workpiece.
1
Always make sure table saw is used for rip cut dados or moldings with the line on the disc (Fig. 48).
Using a straight...
Operating Instructions - Page 64
... 4 must be used in either slot on right side of table where
3
the blade is used.
Attach with the proper operation of the saw blade guard.
Drill 5/32" dia. Using The Miter Gauge
CROSSCUTTING,... to the right of the blade.
64. holes thru (board 3/4" thick, 3" high, and desired
length). Be sure facing does not interfere with two No. 12 round head wood screws 1-1/2" long, 6,
not...
Operating Instructions - Page 74
...STICK 1 to feed using the rip fence. When ripping LONG BOARDS or LARGE PANELS, always use of the blade ONLY.
Continue to feed the work support (Fig. 62). The Bosch table saw outfeed support table kit (TS1001,...ideal accessory to the left hand (Fig. 62). Feed the workpiece by hand until the end is known as cutting a piece of wood with proper use fence on top of auxiliary fence...
Operating Instructions - Page 78
The 4100 table saw can accommodate dado cutting up to 13/16" maximum), chipper blades and spacers can be different, check for information on the shaft. WARNING Bosch Dado Blade Table Insert No.TS1007 (comes with these warnings may be tightly joined together. Failure to comply with a dado accessory washer). Remove standard table insert plate. Raise saw
is an accessory...
Operating Instructions - Page 80
... height accordingly.
! Using scrap wood, make sure all Operation/Safety ...is not plugged into power source. sawing.
! NOTE: Because dado cuts ...tool is maintained. cutting. Read and follow all components are non-thru (blind) cuts. If the stacked width is held
against the miter gauge
(see page 74). Lower the blades below the table top and insert the Bosch Dado Table...
Operating Instructions - Page 82
...the 4100 table saw blade always aligns with an additional thick washer/spacer; thru sawing....blade washer and saw into a power source; NOTE: Leave inner blade washer on non- Lower the cutters below the table top and insert the Bosch Molding Table Insert (TS1009) (Fig. 72). Raise the cutters to the original positions (see
page 74). Plug saw blade (see page 26). Using scrap wood...
Operating Instructions - Page 84
..., such as aluminum or copper, even with abrasive cut-off
wheels.
Maintaining Your Table Saw
Maintenance
! blades) with a dry clean cloth to perform
cuts not covered in any dust that...attempt to prevent deterioration from power source outlet before
maintaining or lubricating your cutting tools (i.e. Cliffe. Do not allow workpieces to cut , or damaged in this manual.
...
Similar Questions
How To Increase Your Work Surface Bosch Table Saw
(Posted by raegr 9 years ago)
How Can I Tell The Age Of A Used Bosch 4100 Table Saw?
(Posted by lolanddi 10 years ago)
Bosch 4100 Worksite Table Saw: The Motor Turns Very Hard By Hand.
The motor turns very hard by hand. It will not run. The blade is clean & free. It seems to be in...
The motor turns very hard by hand. It will not run. The blade is clean & free. It seems to be in...
(Posted by tstolte 12 years ago)
Was There A Recall Onthe Bosch 4100 Table Saw And If So What Serial Number Does
(Posted by joshuaburk 14 years ago)